Winkler audio CDP-2104 User manual

CDP2100

www.winkleraudio.cz side 1 from 20

CD – MP3 PLAYER CDP2100 series.

User’s guide

CDP2100

www.winkleraudio.cz side 2 from 20

Table of Contents:

Introduction: ............................................................................................................................... 3

Getting Started: .......................................................................................................................... 4

Maintenance Tips: ...................................................................................................................... 4

Accessories Supplied: ................................................................................................................ 4

Optional Accessories: ................................................................................................................. 4

CD Unit: ..................................................................................................................................... 5

Control Unit: .............................................................................................................................. 5

Display: ...................................................................................................................................... 6

Step1: Connect ........................................................................................................................... 6

Step2: Start-up ............................................................................................................................ 7

CD Audio Play back: ...................................................................................................... 7

MP3 CD Playback: .......................................................................................................... 8

Functions and Programming: .......................................................................................... 8

REPEAT function: .......................................................................................................... 8

A-PAUSE function: ......................................................................................................... 8

Programming: .................................................................................................................. 9

Storing your own tracks sequence to program: ............................................................... 9

Program editing: .............................................................................................................. 9

Cancellation of all programs: .......................................................................................... 9

REMOTE: ..................................................................................................................... 10

Step3: Basic Setting ................................................................................................................. 11

Description of the Setup Menu Items ............................................................................ 11

MIDI function: ......................................................................................................................... 12

Connection ................................................................................................................ 12

Mixing Console MIDI Control:................................................................................. 12

MUTE functions Control: ......................................................................................... 13

Control by FADER .................................................................................................... 13

MUTE functions Control and by FADER ................................................................. 13

MUTE functions + FADER STOP............................................................................ 13

Technical Data: ........................................................................................................................ 14

Service and Sales centre : ......................................................................................................... 15

Provisions of Warranty: ........................................................................................................... 16

NOTES: .................................................................................................................................... 18

CERTIFICATE OF WARRANTY: ......................................................................................... 19

CDP2100

www.winkleraudio.cz side 3 from 20

Introduction:

Double CD player is intended for handling the musical recordings in form of CD-AUDIO

and MP3 (MP1&2 Layer3). This device was proposed for needs of theaters and concert

circuits, where settings characteristics and safety are the main requirements. Computer

DVD mechanics with antishock system, which can play back any CD, are used as CD

players. The control was proposed according to requirements of sound engineers and was

tested in long term full operating conditions. Considerable advantage is display

CD-TEXT in two rows – album interpreter, album name – song interpreter, song name.

All necessary data are well displayed on two big enlightened display panels.

The CD player is divided into two device boxes for easy operation and installation, 2U

CD unit and 2U control unit. Unit connection is implemented by cable (CAN9pin). Audio

signal outputs are separated for each CD player and are brought out on the back panel of

CD unit in formats Analog asymmetric, Analog servo symmetric and Digital S/Pdif. For

easy connection with mixing desks, which enable operation through MIDI, the CD player

is equipped with interface MIDI/IN and MIDI/THRU. There is connector Remote on

back panel for needs of simple remote control.

CDP2100

www.winkleraudio.cz side 4 from 20

Getting Started:

Maintenance Tips:

Particular parts of device are sensitive to environment effects, especially to temperature,

moisture and dustiness. To clean device use soft and dry cloth – do not use alcohol,

thinner or benzine. Read instructions carefully before use chemical impregnated cloth.

In the interest of ensuring long term audible experience, adhere to following instructions.

 The laser optics of DVD device can be soiled with dust and dirt that can disable

disk play back. According to device using frequency and surrounding, use

cleaning set for scanning optics of DVD approximately once a year. Read

instructions carefully before use.

 Do not put down device on amplifiers or other systems, which can heat. High

temperature can harm device.

 Before device move make sure that there is no disk inside. Otherwise, you risk

that device and disk can be damaged

 Do not cover the built-in ventilator holes on the back panel.

 Back-up power supply for setting retention is involved. In case of the loss of

setting and programs change floating battery (type: B-CR2430A). Average life

time of battery is 3 years. It is better to entrust the change of battery to special

service. Isolate device from power supply while manipulating.

Accessories Supplied:

Check completeness of accessories supplied.

1) 2U CD unit

2) 2U Control unit

3) 2m connecting cable between CD unit and Control unit (Canon 9pin-Canon

9pin)

4) Power cable

5) Test CD

6) User’s guide

7) Warranty

Optional Accessories:

Not part of delivery, but available on demand.

1) Link cable CINCH/CINCH 3m

2) Link cable XLR-M/XLR-F 3m

3) Link cable S/PDIF CINCH/CINCH 3m

4) Cable remote control

5) MIDI cable DIN5p x DIN5p 3m

CDP2100

www.winkleraudio.cz side 5 from 20

CD Unit:

CD unit contains 2 CD drives named CD A and CD B. To turn on the device press button

“Power”. For opening CD use button “Eject”.

CD - A CD - B

EJECTEJECT

POWER

I

0

Control Unit:

Control unit combines control items for operating the CD player.

CD - A CD - B

1) Stop

2) Previous song/piece

3) Play/Pause

4) Next song/piece

5) Program and function buttons

6) Rotary step driver for program functions

7) Display panels

CDP2100

www.winkleraudio.cz side 6 from 20

Display:

910 11

12

Display description:

1. CD interpreter – song interpreter (MP3 – file name)

2. Total playing time of CD

3. Number of pieces on CD

4. Operate position: Play, Stop, Pause ( , , )

5. Functions: (previous and next song), (hift within the song),

(shift in files – only MP3)

6. Functions: , , , , ,

, ,

7. Program display Pr 01/06 (program number / total number of program steps used)

8. CD format display = CD audio, = data CD MP3

9. Time from the beginning of song

10. Time remaining till the end of song

11. Playing song / total number of pieces on CD

12. CD title – song title

13. MIDI On

Step1: Connect

All terminal connectors are situated on the back of the CD unit.

DIGITAL

S/PDIF

CD-A

CD-B

CD-A CD-B

ANALOG OUT

L L

R R

RE MOT E

INTHRU

MID I CO NTR O L

PANE L

POWE R

INO UT

ANALO G SERVO BALANC ED OUTP UT

CD-A CD- B

L R L R

SERIAL NO : TYPE: CDP-2 101

CDP-2 102

CDP-2 103

CDP-2 104

200706210401

1 2 3 4 5 6 78

1. S/PDIF output CD A and CD B (2x CINCH)

2. Analog output CD A and CD B (4x CINCH)

3. Remote – remote control (DIN 8pin)

4. MIDI THRU (DIN 5pin)

5. MIDI IN (DIN 5pin)

6. Connecting the control unit

7. Analog servo symmetrical output CD A and CD B (4x XLR – Male)

8. Power cable (IEC Male) – (IEC Female)

1234

567

8

CDP2100

www.winkleraudio.cz side 7 from 20

Control unit – back side:

1

2007080014

Firstly connect through the control unit (connector 1) and CD unit (connector 6), then

connect power cable and turn on the device. Connect through your audio system and CD

unit with requested cable and continue according to operating instructions.

Step2: Start-up

This device is ready after produce, so it does not need any settings. After insertion of

audio CD and choosing function Play, device plays back your selected CD.

For professionals the “Test CD” is enclosed. The test signal both for checking correctness

of connected cables (test Left channel and Right channel) and settings the whole network

(1 kHz, 0dBu) is recorded on this Test CD.

CD Audio Play back:

1. Turn on device by power supply switch (POWER) on the CD unit.

2. Press button “Eject” at chosen drive (“Eject” appears on display)

3. Insert CD and press button Eject again, “Loading” appears on display.

4. In case of right CD, on display appear table of total number of songs (for example

T12 means that there are songs), total playing time and interpreter and title if the

CD contains CD-TEXT. In case of defective or incompatible CD, “No Audio”

appears on display. In this case press button “Eject” and take out CD.

5. Pressing button PLAY/PAUSE you start up or stop playing CD.

6. To move in songs/pieces forwards and backwards use buttons SKIP (2 and 4), or

turn the wheel (6)

7. Pressing the wheel (6) you switch between function SKIP or SEEK, function

SEEK stops playing and enable shifting within the song for 1-30s according to

adjustment in “Setup menu”. Function SEEK is not supported in MP3.

8. Button (1) STOP stops playing.

1 2 3 4

CDP2100

www.winkleraudio.cz side 8 from 20

Warning – advice:

If the function PLAY/PAUSE is chosen, motor of CD drive is still going. Therefore

choose function STOP in case you do not use CD player for a longer time. Motor of

CD player will have turned off till 2 minutes. You economize the CD drive this way.

MP3 CD Playback:

Functions are the same as with playing CD Audio, only with the difference of pressing

the wheel (6), when you switch between folders ( – Skip Folder) instead of shift

within the track. Other control is the same as with CD Audio. The function shift within

the track (SEEK) is not supported. Mode Multisession is not supported while reading file

system CD ISO9660. The system plays audio tracks located in first session. Output

S/PDIF is inactive while playing MP3.

Functions and Programming:

1 2 3 4 5 6 7 8 9

1. Turning on/off the program

2. Backward move in program

3. Forward move in program

4. Saving the program step

5. Deleting the program step

6. Insertion the program step

7. Setup menu (setting the basic functions of CD player), temporarily turn on/off the

“MIDI” function in section “Play and Pause”

8. Repeat (tracks or discs) – only if A-Pause is not tuned on. If A-Pause is turned on,

it switches the functions A-pause, A-pause(E), A-pause(B).

9. Turning on/off A-PAUSE

REPEAT function:

By pressing button (8) you choose between function - playing the whole disk

from the beginning to the end, and function – repeating one track,

– repeating the whole disk ( repeating folder in MP3),

– playing disk in CD-A and then playing disk in CD-B, in case of setting this

function on both CD players, the playing order is followed: CD1 – CD2 – CD1

….following CD must be prepared in mode STOP, in case of other function

(PLAY/PAUSE) playing next CD does not start up.

A-PAUSE function:

To turn on/off A-Pause function use button A-Pause ON/OFF (9). The basic setting of

A-Pause means that the player stops after playing each track before starting playing next

one. If you press button PLAY/PAUSE during the playing, it will hold up playing and by

follow-up pressing PLAY/PAUSE, the playing will continue to the end of track.

CDP2100

www.winkleraudio.cz side 9 from 20

Using button (8) you switch between courses of function A-pause:

 by pressing PLAY/PAUSE during playing it holds up playing and by

follow-up pressing PLAY/PAUSE the playing will continue to the end of track.

 by pressing PLAY/PAUSE during playing it stops playing and CD

player will set to next track.

 by pressing PLAY/PAUSE during playing it stops playing and CD

player will set to the start of playing track, if the track plays to the end, the player

will stop when next track.

It is possible to switch from CONTINUE function to A-PAUSE function, and conversely.

If you skip between functions during playing, take into account small delay due to

changing the playing mode.

Programming:

Programming is instrumental to store the sequence of playing tracks of particular CD. CD

player enables saving as much as 100 CDs into memory. The algorithm used for CD

identification eliminates allocation of the program to wrong CD (in case of two identical

CDs, algorithm recognizes them as one CD disc and assigns them the same program).

Program memory of CD-A and CD-B is merged, it means that your CD program made in

drive CD-A is possible to play in CD-B with right program. It is possible to pre-set as

much as 99 program steps for one CD (according to CD Audio standards, where max. 99

tracks are permitted).

Storing your own tracks sequence to program:

1. Press button PLAY/PAUSE, icon Pause appears on display

2. By buttons previous, next track or by wheel SKIP choose the track, e.g. track n.2

and press button STORE (4), the track will be saved into program and on display

appears T02-01/01 (T02= your chosen track, 01/01number of program/total

number of program steps used). Repeating procedure 2. you store other tracks.

3. To delete wrong record press button DELETE (5).

4. If you forget about some track and need to put it in the program, use button (2)

and (3) to choose the position in program, where you want to insert the track and

press button INSERT (6), your chosen track will be inserted in front of selected

position in program.

Program editing:

If you need to adjust already existing program, process is followed:

1. Turn off the program by pressing button ON/OFF, yellow control lamp is not on.

2. Choose place in program by buttons (2) and (3).

3. Use buttons DELETE (5) and INSERT (6) to adjust the program.

Cancellation of all programs:

You can cancel all of the programs from the memory pursuant to instructions in chapter

“Basic settings” article 3.

Program activation

Press button STOP, the icon “ ” appears. Activate the program by button Program

ON/OFF, the yellow control lamp lights up. Press PLAY/PAUSE and start up CD

playback according to program. If you have the automatic playback turned on in basic

CDP2100

www.winkleraudio.cz side 10 from 20

settings, so after placing the already programmed CD, the player automatically switches

to mode STOP while function CONTINUE, or to mode PAUSE while Function A-

AUSE.

You cancel the function of the program in mode STOP by pressing the button ON/OFF

(1), the yellow control lamp switches off.

Warning

The digital output S/PDIF has not implemented functions MUTE-OUT, and so some

frame at beginning of next song can be replayed when shifting in program or between

tracks. Therefore use solely analog outputs for professional operation.

REMOTE: remote control through the use of cable (not part of delivery)

In case you need remote control, the cable remote control is proposed. It contains two

buttons PLAY/PAUSE and yellow, green LED diodes for position signaling. Remote

control is plugging in REMOTE (DIN8pin) on the back side panel of CD unit. In SETUP

MENU you can set, that by pressing the button, you start or stop playback, or only start

playback, or the remote control is turned off.

Connecting the connector DIN8p REMOTE

Limiting resistors for LED diodes are in device. Use low power LED diodes max 2mA.

Buttons and LED are connected towards GND. If the player is in function STOP, no

control lamp lights.

1. button (play/pause) CD-B

2. GND

3. +yellow LED(PAUSE) CD-A

4. +GREEN LED (PLAY) CD-B

5. +YELLOW LED (PAUSE) CD-B

6. NC

7. button (play/pause) CD-A

8. +green LED (PLAY) CD-A

1

2

3

4 5

6

78

Pohled na zásuvku

DIN 8P

CDP2100

www.winkleraudio.cz side 11 from 20

Step3: Basic Setting

SETUP MENU

1/4

2/4

3/4

4/4

Descriptions - Factory configuration – in red

1

SEEK RESOLUTION

1-30s

step resolution of the wheel SEEK in 1 – 30 seconds

2

REMOTE MODE

Play/Pause

Play

No

cable remote function

3

DELETE ALL CD PROGRAM

NO

YES

delete all CD program from memory

4

CD-A SET PROGRAM ON - CD LOAD

NO

YES

activation function start after insertion CD

5

CD-B SET PROGRAM ON - CD LOAD

NO

YES

activation function start after insertion CD

6

CD-A SET MODE POWER ON

CONTINUE

APAUSE

APAUSE (E)

APAUSE (B)

activate the function after turning on

7

CD-B SET MODE POWER ON

CONTINUE

APAUSE

APAUSE (E)

APAUSE (B)

activate the function after turning on

8

SET LINKING OUTPUT CD A-B

NO

YES

turn on/off mergence the output CD A, B into A – only analog outputs

9

RESET DEFAULT SETTING

NO

YES

delete all memory and set factory configuration

10

MIDI

YES

NO

Turn on MIDI

11

MIDI Channel

LEARN-1-16

setting MIDI channel

12

MIDI Control CD A

MUTE

FADER

MUTE+FADER

STOP

selection of start/stop function CD A operating via MUTE – FADER

13

MIDI Control CD B

MUTE

FADER

MUTE+FADER

STOP

selection of start/stop function CD B operating via MUTE – FADER

14

Mixing Console MIDI Control

Allen&Heath

Yamaha TABLE

Yamaha

NRPN

0-127(64)

Setting type MIXING CONSOLE - or setting bounds of MUTE switching

15

CD-A-MIDI MUTE Control No.

LEARN-1-127

LEARN-0-

3FFF

setting channel MUTE number for CD A

16

CD-B-MIDI MUTE Control No.

LEARN-1-127

LEARN-0-

3FFF

setting channel MUTE number for CD B

17

CD-A-MIDI FADER Control No.

LEARN-1-127

LEARN-0-

3FFF

setting FADER number for CD A

18

CD-A-MIDI FADER Control Up

LEARN-1-127 (3)

1-3FFF (3)

setting FADER position number for start, greater than Dn.

19

CD-A-MIDI FADER Up Delay

0-2520ms

Setting delay start CD near function FADER UP

20

CD-A-MIDI FADER Control Dn

LEARN-0-126

0-3FFE

setting FADER position number for pause 0 -126, less than Up.

21

CD-B-MIDI FADER Control No.

LEARN-1-126

LEARN-0-

3FFF

setting FADER number for CD B

22

CD-B-MIDI FADER Control Up

LEARN-1-127 (3)

1-3FFF (3)

setting FADER position number for start, greater than Dn

23

CD-B-MIDI FADER Up Delay

0-2520ms

Setting delay start CD near function FADER UP

24

CD-B-MIDI FADER Control Dn

LEARN-0-126

0-3FFE

setting FADER position number for pause 0 -126, less than Up.

Description of the Setup Menu Items

To get to the setup menu press key (7). To move in menu up and down move the wheel (6), to

choose the function and to confirm it press the wheel (6) [Enter].

1. SEEK RESOLUTION – through function SEEK you set the period (1 – 30s) after which

you will be moving within the track

2. REMOTE MODE - Selecting Remote function "Play/Pause" - the remote control

button will start playing and when they re-pressing will stop (or skip to the next track

according functions under A-Pause). 'PLAY' - the remote control button will start

playing and further acts under chosen function A-Pause, Continue, re-press does not

affect the play. "No" - remote function is turned off.

3. DELETE ALL CD PROGRAM – this will clear all programmed order of all CDs from

internal memory. If you want to choose this function, no CD can be inserted in; otherwise

this function is ignored. By the wheel choose Yes/No and confirm by pressing the wheel

(6) [Enter].

4. CD-A SET PROGRAM ON – CD LOAD – This function provides automatic turning

on after insert CD. The function turns on automatically, if the program accordant with CD

was found. If the program is not found, function will not turn on. Choose yes/no to set

this program.

5. CD-B SET PROGRAM ON - CD LOAD – the same as point 4.

6. CD-A SET MODE POWER ON – if you choose this function, the device after starting

feeding will set chosen item: [Continue] playing whole CD without stopping, [A-PAUSE]

stopping after playback the track, [A-PAUSE(E)] stopping after playback the track - if

you press PAUSE during playback, it stops playback and sets to next song, [A-

CDP2100

www.winkleraudio.cz side 12 from 20

PAUSE(B)] stopping after playback the track – if you press PAUSE during playback, it

stops the playback and sets to beginning of playing track.

7. CD-B SET MODE POWER ON – the same as point 6

8. SET LINKING OUTPUT CD A-B – this function provides merger of analog outputs

CD-A and CD-B into output CD-A (S/PDIF does not merge, it is still separated). Useful

in case of few inputs at your audio device. Turning on this function, the player, which

was turned on first by pressing button Play starts playing (icon _ appears in right corner

of display ). Other output of CD player is disconnected. If you press Play at this

player, the icon appears, the audio output is disconnected. If you want to playback

from the other player, you have to choose Pause or Stop on first player. To turn on/off

this function choose YES/NO.

9. RESET DEFAULT SETTING – this function sets the device into factory configuration

and deletes all program memories. If you want to choose this function, no CD can be

inserted in; otherwise this function is ignored. By the wheel choose Yes/No and confirm

by pressing the wheel (6) [Enter].

10. MIDI turn on/off (Yes/No), possible to turn off by key (7) while Play/Pause

11. -24. setting the control through MIDI. Described in sole chapter.

MIDI function:

To PLAY/PAUSE operating from mixing consoles supporting protocol MIDI is implemented the

operating function via MUTE key or FADER in CD player.

Connection

Connect the mixing console with CD player MIDI through cable and set the output MIDI channel

on mixing console in accordance with operating instructions (mostly channel 16). Set the same

number of channel in setup menu of CD player in item MIDI Channel. If you do not know MIDI

channel, choose function LEARN MODE, confirm by pressing the wheel and press any MUTE

key on mixing console.

Mixing Console MIDI Control:

Set mixing console which you use.

a. Allan&Heath GL/ML series – uses standard MIDI protocol to PLAY/PAUSE operating

by function MUTE from mixing console. This protocol complies with most of analog

consoles, which have MUTE operating through MIDI interface. Function PLAY/PAUSE

(via MUTE) is implemented to the address of NOTE ON, which is the function MUTE on

particular inputs by most mixing consoles.

Notice transmission NOTE ON:

notice NOTE ON – 9n cc vv

n = console MIDI channel number

cc = console channel number

vv = 3FH – PLAY, 7FH – PAUSE

2. YAMAHA Digital cons. TABLE – uses standard instructions MIDI TABLE. To

START/PAUSE operating via function MUTE and FADER are used instructions

described in manual to digital console YAMAHA. This protocol obliges to most of digital

consoles even to other producers. TABLE protocol limitation is to 32 MUTE commands

and 32 FADER commands.

3. Yamaha Digital Cons. NPRN – is special MIDI protocol developed to operating digital

mixing consoles and Yamaha peripherals. This protocol enables full addressing of all

functions of mixing console with no limits

CDP2100

www.winkleraudio.cz side 13 from 20

4. 0 – 127 – this item enables to set switching threshold between PLAY/PAUSE at standard

MIDI protocol. For decision making is commonly used < 64 set off, and > 64 set on. If

you have this decision level set another way at your console, change this value by turning

the wheel (6) and confirm by pressing (enter).

MUTE functions Control:

If you want to control CD player by MUTE function, set up CD-A-MIDI MUTE Control No. to

LEARN MODE (function Learn Mode choose by pressing key 7) and press the wheel (6), notice

LISTENING appears, then press button MUTE on mixing console. If you have MIDI channel

selected properly, the address of MUTE function (1-127 TABLE/0-3FFFNRPN) should appear at

display, confirm this figure by pressing the wheel (6). To set up the other CD repeat the procedure

at CD-B-MIDI Control No.

Control by FADER

To set up the start through FADER, set CD-A-MIDI FADER Control No. to LEARN MODE

(Learn Mode function choose by pressing key 7) and press the wheel (6), notice LISTENING

appears, then shift FADER on mixing console from one extreme position to other, number of

FADER appears at display, confirm it by pressing the wheel (6). Then set values CD-A-MIDI

FADER Control Up and CD-A-MIDI FADER Control Dn according to your request for

position in which the CD should start up or stop (<1 PAUSE, >3 PLAY). The function Learn

mode is implemented In CD-A(B)-MIDI FADER Control Up (Dn) (only Yamaha NRPN), set

FADER to required position and press (7) and Enter, slightly move Fader – the number of

position will be recorded, and confirm by Enter (6). To set up the other CD repeat the procedure

at CD-B-MIDI Control No….provided that Up is grater than Dn. If this function is selected, the

notice “please move FADER to Min/Max” appears after turning on the player, which waits until

meeting this requirement. In CD –A(B)-MIDI FADER Up Delay you set CD start delay while

choosing Fader Up. Time-delay can be set in range 0 – 2520ms (2,5s) after 40ms.

MUTE functions Control and by FADER

There are some limitations to control CD player by MUTE and FADER together. To exclude

contradictory command chaining the special logic based on command sequence is set up. The CD

player performs only the commands from mixing consoles therefore take care while first setting

MUTE and FADER after starting power supply. Mixing consoles get these commands only

while change of condition, therefore if you turn on CD player after setting Mute function on

mixing console, CD player does not take it into account. CD player logic works in the way that if

the MUTE is set on and you push FADER from minimal position, the playback does not turn on

and vice versa. Startup of playback comes in these cases: FADER out of minimum position – you

turn off MUTE, MUTE off and push FADER from minimal position. To stop playback the

process is analogical. If you have chosen this function, the notices “Please press key MUTE

control” , “Please move FADER to Min/Max” appear after turning on the player and waits until

meeting this requirement, otherwise starts could not work.

MUTE functions + FADER STOP

There is everything same as with function MUTE; in addition the player stops while shifting

FADER to minimal position. Start via FADER is not supported. There is no logic applied at this

function.

CDP2100

www.winkleraudio.cz side 14 from 20

Technical Data:

Frequency response .…………………………… 20Hz – 20kHz +-2dB

Analog Output Level - CINCH .…………....…….. 0,775V

Analog Output Level- XLR (servo balanced) ...….. 1,5V

Hum & Noise..……………….…………………….-97dB

Digital Output S/Pdif …………………………..….CINCH (only audio CD)

AES/EBU - 2x XLR Balanced 110ohm, 75 Ohm (unterminated). HD/SD Sync, AES-11, or

Wordclock (48/96 KHz) (only CDP2105)

Laser Device LTE-ON IT (SONY) - DVD-ROM

Dimensions CD Unit 19“ ………………………….483x90x300

Dimensions Control Unit19“…………………...….483x90x38

Power ………………………………………………90-260V/47-63Hz

Fuse……………………………….…………….….T2A/250V

Net Weight… ……………………………………...7,0kg

Weight of CD Unit..…………..……………………5,5kg

Weight of Control Unit ..…………………..…..…..1,5kg

Operation free-air Temperature Range ……..….….15~40°C

Storage Temperature Range ….……………………0~50°C

Backup battery ……………….………………..…. B-CR2430A

Maximum length control cable (Remote) …….…. 100m

Maximum length connecting cable …………….…. 3m (CD Unit <–> Control Unit)

Wiring connectors connecting cable troop CD and Control device CAN9 female:

1-1,2-2,3-NC,4-4,5-5,6-6,7-7,8-8,9-9 cross - section wire 1,2,4,5 on current loading 1A.

MPEG 2.5 LAYER III AUDIO DECODER

 All features specified for Layer III in ISO/IEC 1172-3 (MPEG1 Audio)

 All features specified for Layer III in ISO/IEC 13818-3.2 (MPEG2 Audio)

 SUPPORTING ALL THE MPEG 1 & 2 SAMPLING FREQUENCIES AND THE

EXTENSION TO MPEG 2.5: 48/44.1/32/24/22.05/16/12/11.025/8KHz

 ACCEPTS MPEG 2.5 LAYER III ELEMENTARY COMPRESSED BITSTREAM

WITH DATA RATE FROM 8Kbit/s – 320Kbit/s

CDP2100

www.winkleraudio.cz side 15 from 20

Service and Sales centre :

List of authorized services:

CHRUDIM:

MediaTech spol. s r.o.

Topolská 952

537 05 Chrudim

www.mediatech.cz

[email protected]

Tel.: +420 469 631 555

PRAHA:

AVC Praha s.r.o.

Ocelářská 1

190 00 Praha

www.avcpraha.cz

[email protected]

Tel.: +420 283 892 728

BOSKOVICE:

DISK Multimedia, s.r.o.

Sokolská 13

680 01 Boskovice

www.disk.cz

[email protected]

Tel.: +420 516 802 472(3)

BRNO:

Petr Winkler

Oblá 3

634 00 Brno

www.winkleraudio.cz

[email protected]

Tel.: +420 607 514 509

CDP2100

www.winkleraudio.cz side 16 from 20

Provisions of Warranty:

The company WinklerAudio (hereafter WA) provides the final consumer the guarantee

under the conditions mentioned below:

1. Product was purchased within the retail network in Czech Republic and the

product is used in accordance with appropriate service instruction, technical

norms or safety rules valid in Czech Republic.

2. To claim under this warranty the device installation must be made by agent in

cases of product which demands such installation due to its character.

3. To claim under this warranty the product must be taken before the end of

guarantee period to the dealer where the product was purchased or any other

business premises in which the claim acceptation is possible regarding to range of

sales line or services supplied or eventually turn to place of business. After fault

detection the product can be devolved on authorized service station. In case of

impractical transport of the device, especially concerning special installation, the

repair can be executed direct at consumer’s place, if it conforms to the consumer’s

provisions. Seller’s liability is to give the guarantee in written form (certificate of

warranty) to products, to which WA gives guarantee. In some cases, the seller can

issue proof of purchase instead of certificate of warranty. When claiming the

product it is necessary to put forward the proof of purchase including these

items: name and surname, name and the business firm of the seller, identification

number; in case of corporate – name, identification number and quarters; in case

of individual – name, surname, domicile and certificate of warranty (if purchaser

received it from seller). The warranty validity is not affected by neglecting of

duties concerning issue of certificate of warranty.

4. This warranty does not cover the following:

 any defect or damage that occurs due to fire, water, static electricity, irregular

voltage sources, accident, improper use, wear and mechanical damage

 any defect that occurs due to pollution of device reader and its cleaning

 any defect that occurs due to unprofessional installation, modification, repair or

mishandling (such as an operation performed that is not mentioned in the service

instruction or other section of the instruction, in technical norms or safety rules

valid in Czech Republic)

 any defect or damage that occurs due to transport, which was caused by improper

manipulation (such as an operation performed that is not mentioned in service

instruction or other section of the instruction, in technical norms or safety rules

valid in Czech Republic)

 cleaning and providing regular maintenance

 exhausted batteries, decreased capacity of battery or flown out electrolyte

5. Wear of product and its parts caused by common use (storage battery capacity

decrease, wear of ear peace, wear of mechanical parts, displays, etc.) is not subject

to this warranty and is not considered as contrariety to contract of purchase in

accordance with §616, article 3 of Civil Code (law n.40/1964 Collection as

amended by the subsequent novel, CC hereafter).

6. If some parts of the product are during the guarantee period changed for items

which are not agreed by WA and are not suitable for the product for quality and

safety reason or the product is taken to parts or repaired by non-authorized person,

the purchaser loses his rights to claim. The purchaser also loses these rights in

case of damage or change of items which are instrumental to identification of

product or data identification on certificate of warranty.

CDP2100

www.winkleraudio.cz side 17 from 20

7. The claim of product defect which can be adequately fast corrected will be solved

by defect remove (repair) or change the part of product (according to §616, art.4

CC). Controversial claims need special examination of defect by authorized

service WA (§19, art.4, Law about Consumer’s Protection).

8. Purchaser who sets up a claim to guarantee repair does not have claim for return

of parts of device which were changed.

9. Guarantee period for all products is 24 months (unless WA sets longer period for

the given product) from the time of taking over the product by purchaser. If the

product has to be put to the operation by another subject than the seller, the

guarantee period will start while putting the product to operation provided that

purchaser ordered this setting to operation at latest by three days from product

taking over and accorded cooperation properly and in time. Customer takes note

of that he can not ask the change of product or withdraw from purchase contract

after elapsed guarantee period stated in CC (legal duration guarantee).

10. Purchaser’s rights (which are related to purchase according to special enactments)

are not hurt by providing the warranty.

 actual list of authorized service centers intended for providing guarantee and

after guarantee repairs are stipulated on the web site:

http://www.winkleraudio.cz

CDP2100

www.winkleraudio.cz side 18 from 20

NOTES:

You can find service instructions on the web site: www.winkleraudio.cz in section

“Support”(Podpora) – “Manuals”. Actual list of service centers are in section “Support” –

“Service centers”

CDP2100

www.winkleraudio.cz side 19 from 20

CERTIFICATE OF WARRANTY:

The seller: (name and surname, name and the business firm of the seller, identification

number; in case of corporate – name, identification number and quarters; in case of

individual – name, surname, domicile)

……………………………………………………………….

……………………………………………………………………………………………..

Serial number(s): CD………………………………CP…………………………………..

Date of sale:………………………………

Stamp of the seller – signature:

CDP2100

www.winkleraudio.cz side 20 from 20

Last up - dating of the day: 21.1.2009,11:55:43

Winkler audio CDP-2104 User manual

This manual is also suitable for

Winkler audio CDP-2104 User manual

Other documents