CDP2100
www.winkleraudio.cz side 2 from 20
Table of Contents:
Introduction: ............................................................................................................................... 3
Getting Started: .......................................................................................................................... 4
Maintenance Tips: ...................................................................................................................... 4
Accessories Supplied: ................................................................................................................ 4
Optional Accessories: ................................................................................................................. 4
CD Unit: ..................................................................................................................................... 5
Control Unit: .............................................................................................................................. 5
Display: ...................................................................................................................................... 6
Step1: Connect ........................................................................................................................... 6
Step2: Start-up ............................................................................................................................ 7
CD Audio Play back: ...................................................................................................... 7
MP3 CD Playback: .......................................................................................................... 8
Functions and Programming: .......................................................................................... 8
REPEAT function: .......................................................................................................... 8
A-PAUSE function: ......................................................................................................... 8
Programming: .................................................................................................................. 9
Storing your own tracks sequence to program: ............................................................... 9
Program editing: .............................................................................................................. 9
Cancellation of all programs: .......................................................................................... 9
REMOTE: ..................................................................................................................... 10
Step3: Basic Setting ................................................................................................................. 11
Description of the Setup Menu Items ............................................................................ 11
MIDI function: ......................................................................................................................... 12
Connection ................................................................................................................ 12
Mixing Console MIDI Control:................................................................................. 12
MUTE functions Control: ......................................................................................... 13
Control by FADER .................................................................................................... 13
MUTE functions Control and by FADER ................................................................. 13
MUTE functions + FADER STOP............................................................................ 13
Technical Data: ........................................................................................................................ 14
Service and Sales centre : ......................................................................................................... 15
Provisions of Warranty: ........................................................................................................... 16
NOTES: .................................................................................................................................... 18
CERTIFICATE OF WARRANTY: ......................................................................................... 19
CDP2100
www.winkleraudio.cz side 3 from 20
Introduction:
Double CD player is intended for handling the musical recordings in form of CD-AUDIO
and MP3 (MP1&2 Layer3). This device was proposed for needs of theaters and concert
circuits, where settings characteristics and safety are the main requirements. Computer
DVD mechanics with antishock system, which can play back any CD, are used as CD
players. The control was proposed according to requirements of sound engineers and was
tested in long term full operating conditions. Considerable advantage is display
CD-TEXT in two rows – album interpreter, album name – song interpreter, song name.
All necessary data are well displayed on two big enlightened display panels.
The CD player is divided into two device boxes for easy operation and installation, 2U
CD unit and 2U control unit. Unit connection is implemented by cable (CAN9pin). Audio
signal outputs are separated for each CD player and are brought out on the back panel of
CD unit in formats Analog asymmetric, Analog servo symmetric and Digital S/Pdif. For
easy connection with mixing desks, which enable operation through MIDI, the CD player
is equipped with interface MIDI/IN and MIDI/THRU. There is connector Remote on
back panel for needs of simple remote control.
CDP2100
www.winkleraudio.cz side 4 from 20
Getting Started:
Maintenance Tips:
Particular parts of device are sensitive to environment effects, especially to temperature,
moisture and dustiness. To clean device use soft and dry cloth – do not use alcohol,
thinner or benzine. Read instructions carefully before use chemical impregnated cloth.
In the interest of ensuring long term audible experience, adhere to following instructions.
The laser optics of DVD device can be soiled with dust and dirt that can disable
disk play back. According to device using frequency and surrounding, use
cleaning set for scanning optics of DVD approximately once a year. Read
instructions carefully before use.
Do not put down device on amplifiers or other systems, which can heat. High
temperature can harm device.
Before device move make sure that there is no disk inside. Otherwise, you risk
that device and disk can be damaged
Do not cover the built-in ventilator holes on the back panel.
Back-up power supply for setting retention is involved. In case of the loss of
setting and programs change floating battery (type: B-CR2430A). Average life
time of battery is 3 years. It is better to entrust the change of battery to special
service. Isolate device from power supply while manipulating.
Accessories Supplied:
Check completeness of accessories supplied.
1) 2U CD unit
2) 2U Control unit
3) 2m connecting cable between CD unit and Control unit (Canon 9pin-Canon
9pin)
4) Power cable
5) Test CD
6) User’s guide
7) Warranty
Optional Accessories:
Not part of delivery, but available on demand.
1) Link cable CINCH/CINCH 3m
2) Link cable XLR-M/XLR-F 3m
3) Link cable S/PDIF CINCH/CINCH 3m
4) Cable remote control
5) MIDI cable DIN5p x DIN5p 3m
CDP2100
www.winkleraudio.cz side 5 from 20
CD Unit:
CD unit contains 2 CD drives named CD A and CD B. To turn on the device press button
“Power”. For opening CD use button “Eject”.
CD - A CD - B
EJECTEJECT
POWER
I
0
Control Unit:
Control unit combines control items for operating the CD player.
CD - A CD - B
1) Stop
2) Previous song/piece
3) Play/Pause
4) Next song/piece
5) Program and function buttons
6) Rotary step driver for program functions
7) Display panels
CDP2100
www.winkleraudio.cz side 6 from 20
Display:
910 11
12
Display description:
1. CD interpreter – song interpreter (MP3 – file name)
2. Total playing time of CD
3. Number of pieces on CD
4. Operate position: Play, Stop, Pause ( , , )
5. Functions: (previous and next song), (hift within the song),
(shift in files – only MP3)
6. Functions: , , , , ,
, ,
7. Program display Pr 01/06 (program number / total number of program steps used)
8. CD format display = CD audio, = data CD MP3
9. Time from the beginning of song
10. Time remaining till the end of song
11. Playing song / total number of pieces on CD
12. CD title – song title
13. MIDI On
Step1: Connect
All terminal connectors are situated on the back of the CD unit.
DIGITAL
S/PDIF
CD-A
CD-B
CD-A CD-B
ANALOG OUT
L L
R R
RE MOT E
INTHRU
MID I CO NTR O L
PANE L
POWE R
INO UT
ANALO G SERVO BALANC ED OUTP UT
CD-A CD- B
L R L R
SERIAL NO : TYPE: CDP-2 101
CDP-2 102
CDP-2 103
CDP-2 104
200706210401
1 2 3 4 5 6 78
1. S/PDIF output CD A and CD B (2x CINCH)
2. Analog output CD A and CD B (4x CINCH)
3. Remote – remote control (DIN 8pin)
4. MIDI THRU (DIN 5pin)
5. MIDI IN (DIN 5pin)
6. Connecting the control unit
7. Analog servo symmetrical output CD A and CD B (4x XLR – Male)
8. Power cable (IEC Male) – (IEC Female)
1234
567
8
CDP2100
www.winkleraudio.cz side 7 from 20
Control unit – back side:
1
2007080014
Firstly connect through the control unit (connector 1) and CD unit (connector 6), then
connect power cable and turn on the device. Connect through your audio system and CD
unit with requested cable and continue according to operating instructions.
Step2: Start-up
This device is ready after produce, so it does not need any settings. After insertion of
audio CD and choosing function Play, device plays back your selected CD.
For professionals the “Test CD” is enclosed. The test signal both for checking correctness
of connected cables (test Left channel and Right channel) and settings the whole network
(1 kHz, 0dBu) is recorded on this Test CD.
CD Audio Play back:
1. Turn on device by power supply switch (POWER) on the CD unit.
2. Press button “Eject” at chosen drive (“Eject” appears on display)
3. Insert CD and press button Eject again, “Loading” appears on display.
4. In case of right CD, on display appear table of total number of songs (for example
T12 means that there are songs), total playing time and interpreter and title if the
CD contains CD-TEXT. In case of defective or incompatible CD, “No Audio”
appears on display. In this case press button “Eject” and take out CD.
5. Pressing button PLAY/PAUSE you start up or stop playing CD.
6. To move in songs/pieces forwards and backwards use buttons SKIP (2 and 4), or
turn the wheel (6)
7. Pressing the wheel (6) you switch between function SKIP or SEEK, function
SEEK stops playing and enable shifting within the song for 1-30s according to
adjustment in “Setup menu”. Function SEEK is not supported in MP3.
8. Button (1) STOP stops playing.
1 2 3 4
CDP2100
www.winkleraudio.cz side 8 from 20
Warning – advice:
If the function PLAY/PAUSE is chosen, motor of CD drive is still going. Therefore
choose function STOP in case you do not use CD player for a longer time. Motor of
CD player will have turned off till 2 minutes. You economize the CD drive this way.
MP3 CD Playback:
Functions are the same as with playing CD Audio, only with the difference of pressing
the wheel (6), when you switch between folders ( – Skip Folder) instead of shift
within the track. Other control is the same as with CD Audio. The function shift within
the track (SEEK) is not supported. Mode Multisession is not supported while reading file
system CD ISO9660. The system plays audio tracks located in first session. Output
S/PDIF is inactive while playing MP3.
Functions and Programming:
1 2 3 4 5 6 7 8 9
1. Turning on/off the program
2. Backward move in program
3. Forward move in program
4. Saving the program step
5. Deleting the program step
6. Insertion the program step
7. Setup menu (setting the basic functions of CD player), temporarily turn on/off the
“MIDI” function in section “Play and Pause”
8. Repeat (tracks or discs) – only if A-Pause is not tuned on. If A-Pause is turned on,
it switches the functions A-pause, A-pause(E), A-pause(B).
9. Turning on/off A-PAUSE
REPEAT function:
By pressing button (8) you choose between function - playing the whole disk
from the beginning to the end, and function – repeating one track,
– repeating the whole disk ( repeating folder in MP3),
– playing disk in CD-A and then playing disk in CD-B, in case of setting this
function on both CD players, the playing order is followed: CD1 – CD2 – CD1
….following CD must be prepared in mode STOP, in case of other function
(PLAY/PAUSE) playing next CD does not start up.
A-PAUSE function:
To turn on/off A-Pause function use button A-Pause ON/OFF (9). The basic setting of
A-Pause means that the player stops after playing each track before starting playing next
one. If you press button PLAY/PAUSE during the playing, it will hold up playing and by
follow-up pressing PLAY/PAUSE, the playing will continue to the end of track.
CDP2100
www.winkleraudio.cz side 9 from 20
Using button (8) you switch between courses of function A-pause:
by pressing PLAY/PAUSE during playing it holds up playing and by
follow-up pressing PLAY/PAUSE the playing will continue to the end of track.
by pressing PLAY/PAUSE during playing it stops playing and CD
player will set to next track.
by pressing PLAY/PAUSE during playing it stops playing and CD
player will set to the start of playing track, if the track plays to the end, the player
will stop when next track.
It is possible to switch from CONTINUE function to A-PAUSE function, and conversely.
If you skip between functions during playing, take into account small delay due to
changing the playing mode.
Programming:
Programming is instrumental to store the sequence of playing tracks of particular CD. CD
player enables saving as much as 100 CDs into memory. The algorithm used for CD
identification eliminates allocation of the program to wrong CD (in case of two identical
CDs, algorithm recognizes them as one CD disc and assigns them the same program).
Program memory of CD-A and CD-B is merged, it means that your CD program made in
drive CD-A is possible to play in CD-B with right program. It is possible to pre-set as
much as 99 program steps for one CD (according to CD Audio standards, where max. 99
tracks are permitted).
Storing your own tracks sequence to program:
1. Press button PLAY/PAUSE, icon Pause appears on display
2. By buttons previous, next track or by wheel SKIP choose the track, e.g. track n.2
and press button STORE (4), the track will be saved into program and on display
appears T02-01/01 (T02= your chosen track, 01/01number of program/total
number of program steps used). Repeating procedure 2. you store other tracks.
3. To delete wrong record press button DELETE (5).
4. If you forget about some track and need to put it in the program, use button (2)
and (3) to choose the position in program, where you want to insert the track and
press button INSERT (6), your chosen track will be inserted in front of selected
position in program.
Program editing:
If you need to adjust already existing program, process is followed:
1. Turn off the program by pressing button ON/OFF, yellow control lamp is not on.
2. Choose place in program by buttons (2) and (3).
3. Use buttons DELETE (5) and INSERT (6) to adjust the program.
Cancellation of all programs:
You can cancel all of the programs from the memory pursuant to instructions in chapter
“Basic settings” article 3.
Program activation
Press button STOP, the icon “ ” appears. Activate the program by button Program
ON/OFF, the yellow control lamp lights up. Press PLAY/PAUSE and start up CD
playback according to program. If you have the automatic playback turned on in basic
CDP2100
www.winkleraudio.cz side 10 from 20
settings, so after placing the already programmed CD, the player automatically switches
to mode STOP while function CONTINUE, or to mode PAUSE while Function A-
AUSE.
You cancel the function of the program in mode STOP by pressing the button ON/OFF
(1), the yellow control lamp switches off.
Warning
The digital output S/PDIF has not implemented functions MUTE-OUT, and so some
frame at beginning of next song can be replayed when shifting in program or between
tracks. Therefore use solely analog outputs for professional operation.
REMOTE: remote control through the use of cable (not part of delivery)
In case you need remote control, the cable remote control is proposed. It contains two
buttons PLAY/PAUSE and yellow, green LED diodes for position signaling. Remote
control is plugging in REMOTE (DIN8pin) on the back side panel of CD unit. In SETUP
MENU you can set, that by pressing the button, you start or stop playback, or only start
playback, or the remote control is turned off.
Connecting the connector DIN8p REMOTE
Limiting resistors for LED diodes are in device. Use low power LED diodes max 2mA.
Buttons and LED are connected towards GND. If the player is in function STOP, no
control lamp lights.
1. button (play/pause) CD-B
2. GND
3. +yellow LED(PAUSE) CD-A
4. +GREEN LED (PLAY) CD-B
5. +YELLOW LED (PAUSE) CD-B
6. NC
7. button (play/pause) CD-A
8. +green LED (PLAY) CD-A
1
2
3
4 5
6
78
Pohled na zásuvku
DIN 8P
CDP2100
www.winkleraudio.cz side 11 from 20
Step3: Basic Setting
SETUP MENU
1/4
2/4
3/4
4/4
Descriptions - Factory configuration – in red
1
SEEK RESOLUTION
1-30s
step resolution of the wheel SEEK in 1 – 30 seconds
2
REMOTE MODE
Play/Pause
Play
No
cable remote function
3
DELETE ALL CD PROGRAM
NO
YES
delete all CD program from memory
4
CD-A SET PROGRAM ON - CD LOAD
NO
YES
activation function start after insertion CD
5
CD-B SET PROGRAM ON - CD LOAD
NO
YES
activation function start after insertion CD
6
CD-A SET MODE POWER ON
CONTINUE
APAUSE
APAUSE (E)
APAUSE (B)
activate the function after turning on
7
CD-B SET MODE POWER ON
CONTINUE
APAUSE
APAUSE (E)
APAUSE (B)
activate the function after turning on
8
SET LINKING OUTPUT CD A-B
NO
YES
turn on/off mergence the output CD A, B into A – only analog outputs
9
RESET DEFAULT SETTING
NO
YES
delete all memory and set factory configuration
10
MIDI
YES
NO
Turn on MIDI
11
MIDI Channel
LEARN-1-16
setting MIDI channel
12
MIDI Control CD A
MUTE
FADER
MUTE+FADER
MUTE+FADER
STOP
selection of start/stop function CD A operating via MUTE – FADER
13
MIDI Control CD B
MUTE
FADER
MUTE+FADER
MUTE+FADER
STOP
selection of start/stop function CD B operating via MUTE – FADER
14
Mixing Console MIDI Control
Allen&Heath
Yamaha TABLE
Yamaha
NRPN
0-127(64)
Setting type MIXING CONSOLE - or setting bounds of MUTE switching
15
CD-A-MIDI MUTE Control No.
LEARN-1-127
LEARN-1-127
LEARN-0-
3FFF
setting channel MUTE number for CD A
16
CD-B-MIDI MUTE Control No.
LEARN-1-127
LEARN-1-127
LEARN-0-
3FFF
setting channel MUTE number for CD B
17
CD-A-MIDI FADER Control No.
LEARN-1-127
LEARN-0-
3FFF
setting FADER number for CD A
18
CD-A-MIDI FADER Control Up
LEARN-1-127 (3)
1-3FFF (3)
setting FADER position number for start, greater than Dn.
19
CD-A-MIDI FADER Up Delay
0-2520ms
Setting delay start CD near function FADER UP
20
CD-A-MIDI FADER Control Dn
LEARN-0-126
0-3FFE
setting FADER position number for pause 0 -126, less than Up.
21
CD-B-MIDI FADER Control No.
LEARN-1-126
LEARN-0-
3FFF
setting FADER number for CD B
22
CD-B-MIDI FADER Control Up
LEARN-1-127 (3)
1-3FFF (3)
setting FADER position number for start, greater than Dn
23
CD-B-MIDI FADER Up Delay
0-2520ms
Setting delay start CD near function FADER UP
24
CD-B-MIDI FADER Control Dn
LEARN-0-126
0-3FFE
setting FADER position number for pause 0 -126, less than Up.
Description of the Setup Menu Items
To get to the setup menu press key (7). To move in menu up and down move the wheel (6), to
choose the function and to confirm it press the wheel (6) [Enter].
1. SEEK RESOLUTION – through function SEEK you set the period (1 – 30s) after which
you will be moving within the track
2. REMOTE MODE - Selecting Remote function "Play/Pause" - the remote control
button will start playing and when they re-pressing will stop (or skip to the next track
according functions under A-Pause). 'PLAY' - the remote control button will start
playing and further acts under chosen function A-Pause, Continue, re-press does not
affect the play. "No" - remote function is turned off.
3. DELETE ALL CD PROGRAM – this will clear all programmed order of all CDs from
internal memory. If you want to choose this function, no CD can be inserted in; otherwise
this function is ignored. By the wheel choose Yes/No and confirm by pressing the wheel
(6) [Enter].
4. CD-A SET PROGRAM ON – CD LOAD – This function provides automatic turning
on after insert CD. The function turns on automatically, if the program accordant with CD
was found. If the program is not found, function will not turn on. Choose yes/no to set
this program.
5. CD-B SET PROGRAM ON - CD LOAD – the same as point 4.
6. CD-A SET MODE POWER ON – if you choose this function, the device after starting
feeding will set chosen item: [Continue] playing whole CD without stopping, [A-PAUSE]
stopping after playback the track, [A-PAUSE(E)] stopping after playback the track - if
you press PAUSE during playback, it stops playback and sets to next song, [A-
CDP2100
www.winkleraudio.cz side 12 from 20
PAUSE(B)] stopping after playback the track – if you press PAUSE during playback, it
stops the playback and sets to beginning of playing track.
7. CD-B SET MODE POWER ON – the same as point 6
8. SET LINKING OUTPUT CD A-B – this function provides merger of analog outputs
CD-A and CD-B into output CD-A (S/PDIF does not merge, it is still separated). Useful
in case of few inputs at your audio device. Turning on this function, the player, which
was turned on first by pressing button Play starts playing (icon _ appears in right corner
of display ). Other output of CD player is disconnected. If you press Play at this
player, the icon appears, the audio output is disconnected. If you want to playback
from the other player, you have to choose Pause or Stop on first player. To turn on/off
this function choose YES/NO.
9. RESET DEFAULT SETTING – this function sets the device into factory configuration
and deletes all program memories. If you want to choose this function, no CD can be
inserted in; otherwise this function is ignored. By the wheel choose Yes/No and confirm
by pressing the wheel (6) [Enter].
10. MIDI turn on/off (Yes/No), possible to turn off by key (7) while Play/Pause
11. -24. setting the control through MIDI. Described in sole chapter.
MIDI function:
To PLAY/PAUSE operating from mixing consoles supporting protocol MIDI is implemented the
operating function via MUTE key or FADER in CD player.
Connection
Connect the mixing console with CD player MIDI through cable and set the output MIDI channel
on mixing console in accordance with operating instructions (mostly channel 16). Set the same
number of channel in setup menu of CD player in item MIDI Channel. If you do not know MIDI
channel, choose function LEARN MODE, confirm by pressing the wheel and press any MUTE
key on mixing console.
Mixing Console MIDI Control:
Set mixing console which you use.
a. Allan&Heath GL/ML series – uses standard MIDI protocol to PLAY/PAUSE operating
by function MUTE from mixing console. This protocol complies with most of analog
consoles, which have MUTE operating through MIDI interface. Function PLAY/PAUSE
(via MUTE) is implemented to the address of NOTE ON, which is the function MUTE on
particular inputs by most mixing consoles.
Notice transmission NOTE ON:
notice NOTE ON – 9n cc vv
n = console MIDI channel number
cc = console channel number
vv = 3FH – PLAY, 7FH – PAUSE
2. YAMAHA Digital cons. TABLE – uses standard instructions MIDI TABLE. To
START/PAUSE operating via function MUTE and FADER are used instructions
described in manual to digital console YAMAHA. This protocol obliges to most of digital
consoles even to other producers. TABLE protocol limitation is to 32 MUTE commands
and 32 FADER commands.
3. Yamaha Digital Cons. NPRN – is special MIDI protocol developed to operating digital
mixing consoles and Yamaha peripherals. This protocol enables full addressing of all
functions of mixing console with no limits
CDP2100
www.winkleraudio.cz side 13 from 20
4. 0 – 127 – this item enables to set switching threshold between PLAY/PAUSE at standard
MIDI protocol. For decision making is commonly used < 64 set off, and > 64 set on. If
you have this decision level set another way at your console, change this value by turning
the wheel (6) and confirm by pressing (enter).
MUTE functions Control:
If you want to control CD player by MUTE function, set up CD-A-MIDI MUTE Control No. to
LEARN MODE (function Learn Mode choose by pressing key 7) and press the wheel (6), notice
LISTENING appears, then press button MUTE on mixing console. If you have MIDI channel
selected properly, the address of MUTE function (1-127 TABLE/0-3FFFNRPN) should appear at
display, confirm this figure by pressing the wheel (6). To set up the other CD repeat the procedure
at CD-B-MIDI Control No.
Control by FADER
To set up the start through FADER, set CD-A-MIDI FADER Control No. to LEARN MODE
(Learn Mode function choose by pressing key 7) and press the wheel (6), notice LISTENING
appears, then shift FADER on mixing console from one extreme position to other, number of
FADER appears at display, confirm it by pressing the wheel (6). Then set values CD-A-MIDI
FADER Control Up and CD-A-MIDI FADER Control Dn according to your request for
position in which the CD should start up or stop (<1 PAUSE, >3 PLAY). The function Learn
mode is implemented In CD-A(B)-MIDI FADER Control Up (Dn) (only Yamaha NRPN), set
FADER to required position and press (7) and Enter, slightly move Fader – the number of
position will be recorded, and confirm by Enter (6). To set up the other CD repeat the procedure
at CD-B-MIDI Control No….provided that Up is grater than Dn. If this function is selected, the
notice “please move FADER to Min/Max” appears after turning on the player, which waits until
meeting this requirement. In CD –A(B)-MIDI FADER Up Delay you set CD start delay while
choosing Fader Up. Time-delay can be set in range 0 – 2520ms (2,5s) after 40ms.
MUTE functions Control and by FADER
There are some limitations to control CD player by MUTE and FADER together. To exclude
contradictory command chaining the special logic based on command sequence is set up. The CD
player performs only the commands from mixing consoles therefore take care while first setting
MUTE and FADER after starting power supply. Mixing consoles get these commands only
while change of condition, therefore if you turn on CD player after setting Mute function on
mixing console, CD player does not take it into account. CD player logic works in the way that if
the MUTE is set on and you push FADER from minimal position, the playback does not turn on
and vice versa. Startup of playback comes in these cases: FADER out of minimum position – you
turn off MUTE, MUTE off and push FADER from minimal position. To stop playback the
process is analogical. If you have chosen this function, the notices “Please press key MUTE
control” , “Please move FADER to Min/Max” appear after turning on the player and waits until
meeting this requirement, otherwise starts could not work.
MUTE functions + FADER STOP
There is everything same as with function MUTE; in addition the player stops while shifting
FADER to minimal position. Start via FADER is not supported. There is no logic applied at this
function.
CDP2100
www.winkleraudio.cz side 14 from 20
Technical Data:
Frequency response .…………………………… 20Hz – 20kHz +-2dB
Analog Output Level - CINCH .…………....…….. 0,775V
Analog Output Level- XLR (servo balanced) ...….. 1,5V
Hum & Noise..……………….…………………….-97dB
Digital Output S/Pdif …………………………..….CINCH (only audio CD)
AES/EBU - 2x XLR Balanced 110ohm, 75 Ohm (unterminated). HD/SD Sync, AES-11, or
Wordclock (48/96 KHz) (only CDP2105)
Laser Device LTE-ON IT (SONY) - DVD-ROM
Dimensions CD Unit 19“ ………………………….483x90x300
Dimensions Control Unit19“…………………...….483x90x38
Power ………………………………………………90-260V/47-63Hz
Fuse……………………………….…………….….T2A/250V
Net Weight… ……………………………………...7,0kg
Weight of CD Unit..…………..……………………5,5kg
Weight of Control Unit ..…………………..…..…..1,5kg
Operation free-air Temperature Range ……..….….15~40°C
Storage Temperature Range ….……………………0~50°C
Backup battery ……………….………………..…. B-CR2430A
Maximum length control cable (Remote) …….…. 100m
Maximum length connecting cable …………….…. 3m (CD Unit <–> Control Unit)
Wiring connectors connecting cable troop CD and Control device CAN9 female:
1-1,2-2,3-NC,4-4,5-5,6-6,7-7,8-8,9-9 cross - section wire 1,2,4,5 on current loading 1A.
MPEG 2.5 LAYER III AUDIO DECODER
All features specified for Layer III in ISO/IEC 1172-3 (MPEG1 Audio)
All features specified for Layer III in ISO/IEC 13818-3.2 (MPEG2 Audio)
SUPPORTING ALL THE MPEG 1 & 2 SAMPLING FREQUENCIES AND THE
EXTENSION TO MPEG 2.5: 48/44.1/32/24/22.05/16/12/11.025/8KHz
ACCEPTS MPEG 2.5 LAYER III ELEMENTARY COMPRESSED BITSTREAM
WITH DATA RATE FROM 8Kbit/s – 320Kbit/s
CDP2100
www.winkleraudio.cz side 15 from 20
Service and Sales centre :
List of authorized services:
CHRUDIM:
MediaTech spol. s r.o.
Topolská 952
537 05 Chrudim
www.mediatech.cz
Tel.: +420 469 631 555
PRAHA:
AVC Praha s.r.o.
Ocelářská 1
190 00 Praha
www.avcpraha.cz
Tel.: +420 283 892 728
BOSKOVICE:
DISK Multimedia, s.r.o.
Sokolská 13
680 01 Boskovice
www.disk.cz
Tel.: +420 516 802 472(3)
BRNO:
Petr Winkler
Oblá 3
634 00 Brno
www.winkleraudio.cz
Tel.: +420 607 514 509
CDP2100
www.winkleraudio.cz side 16 from 20
Provisions of Warranty:
The company WinklerAudio (hereafter WA) provides the final consumer the guarantee
under the conditions mentioned below:
1. Product was purchased within the retail network in Czech Republic and the
product is used in accordance with appropriate service instruction, technical
norms or safety rules valid in Czech Republic.
2. To claim under this warranty the device installation must be made by agent in
cases of product which demands such installation due to its character.
3. To claim under this warranty the product must be taken before the end of
guarantee period to the dealer where the product was purchased or any other
business premises in which the claim acceptation is possible regarding to range of
sales line or services supplied or eventually turn to place of business. After fault
detection the product can be devolved on authorized service station. In case of
impractical transport of the device, especially concerning special installation, the
repair can be executed direct at consumer’s place, if it conforms to the consumer’s
provisions. Seller’s liability is to give the guarantee in written form (certificate of
warranty) to products, to which WA gives guarantee. In some cases, the seller can
issue proof of purchase instead of certificate of warranty. When claiming the
product it is necessary to put forward the proof of purchase including these
items: name and surname, name and the business firm of the seller, identification
number; in case of corporate – name, identification number and quarters; in case
of individual – name, surname, domicile and certificate of warranty (if purchaser
received it from seller). The warranty validity is not affected by neglecting of
duties concerning issue of certificate of warranty.
4. This warranty does not cover the following:
any defect or damage that occurs due to fire, water, static electricity, irregular
voltage sources, accident, improper use, wear and mechanical damage
any defect that occurs due to pollution of device reader and its cleaning
any defect that occurs due to unprofessional installation, modification, repair or
mishandling (such as an operation performed that is not mentioned in the service
instruction or other section of the instruction, in technical norms or safety rules
valid in Czech Republic)
any defect or damage that occurs due to transport, which was caused by improper
manipulation (such as an operation performed that is not mentioned in service
instruction or other section of the instruction, in technical norms or safety rules
valid in Czech Republic)
cleaning and providing regular maintenance
exhausted batteries, decreased capacity of battery or flown out electrolyte
5. Wear of product and its parts caused by common use (storage battery capacity
decrease, wear of ear peace, wear of mechanical parts, displays, etc.) is not subject
to this warranty and is not considered as contrariety to contract of purchase in
accordance with §616, article 3 of Civil Code (law n.40/1964 Collection as
amended by the subsequent novel, CC hereafter).
6. If some parts of the product are during the guarantee period changed for items
which are not agreed by WA and are not suitable for the product for quality and
safety reason or the product is taken to parts or repaired by non-authorized person,
the purchaser loses his rights to claim. The purchaser also loses these rights in
case of damage or change of items which are instrumental to identification of
product or data identification on certificate of warranty.
CDP2100
www.winkleraudio.cz side 17 from 20
7. The claim of product defect which can be adequately fast corrected will be solved
by defect remove (repair) or change the part of product (according to §616, art.4
CC). Controversial claims need special examination of defect by authorized
service WA (§19, art.4, Law about Consumer’s Protection).
8. Purchaser who sets up a claim to guarantee repair does not have claim for return
of parts of device which were changed.
9. Guarantee period for all products is 24 months (unless WA sets longer period for
the given product) from the time of taking over the product by purchaser. If the
product has to be put to the operation by another subject than the seller, the
guarantee period will start while putting the product to operation provided that
purchaser ordered this setting to operation at latest by three days from product
taking over and accorded cooperation properly and in time. Customer takes note
of that he can not ask the change of product or withdraw from purchase contract
after elapsed guarantee period stated in CC (legal duration guarantee).
10. Purchaser’s rights (which are related to purchase according to special enactments)
are not hurt by providing the warranty.
actual list of authorized service centers intended for providing guarantee and
after guarantee repairs are stipulated on the web site:
http://www.winkleraudio.cz
CDP2100
www.winkleraudio.cz side 19 from 20
CERTIFICATE OF WARRANTY:
The seller: (name and surname, name and the business firm of the seller, identification
number; in case of corporate – name, identification number and quarters; in case of
individual – name, surname, domicile)
……………………………………………………………….
……………………………………………………………………………………………..
……………………………………………………………………………………………..
……………………………………………………………………………………………..
Serial number(s): CD………………………………CP…………………………………..
Date of sale:………………………………
Stamp of the seller – signature:
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Winkler audio CDP-2101 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
MAGIX V2000 MKII User guide
-
Hercules DJ Console RMX User manual
-
PRESONUS Studio One User manual
-
-
MAGIX Samplitude Music Studio 15.0 Operating instructions
-
Cakewalk Sonar 8.5 User guide
-
-
-
-