Innovative Electronics DT-PROTO User manual

Brand: Innovative Electronics

Model: DT-PROTO

Type: User manual

18 Pin

18 Pin18 Pin

18 Pin

PIC®

PIC®PIC®

PIC®

DTDT

DT-

-PROTO 18 Pin PIC

PROTO 18 Pin PICPROTO 18 Pin PIC

PROTO 18 Pin PIC

®®

is a single chip module with

PIC16F84A microcontroller and In-Circuit Serial Programming™

(ICSP™). This Module is equipped with pad arrays which can be

used as a place for additional circuit. This Module is suitable for

users who want to experiment, to make prototype or create a

simple application. Examples applications are as LED display

controller, motor driver controller, robot movement controller, and

digital sensor reader.

Hardware specif

Hardware specifHardware specif

Hardware specifications

icationsications

ications

1. PIC16F84A microcontroller with 1K byte Program memory, 64

bytes Data EEPROM, 68 bytes Data RAM, 8 bit Timer.

2. Support PIC

18 pins variants: PIC16C558, PIC16F627A, and

PIC16F628A.

3. Up to 13 pins input/output line capability to drive current

(sink/source) 25mA each.

4. 708 pad arrays are available, non through-hole.

5. Ceramic Resonator 4 Mhz is available.

6. ICSP

's programming port is available.

7. UART RS-232 serial communication line is available with RJ11

connector.

8. Input voltage 9 – 12 VDC at VIN and has output voltage +5V

(VCC).

Layout and Jumper setting

Layout and Jumper settingLayout and Jumper setting

Layout and Jumper setting

Pad for VIN, GND, +5V, and I/O pin has a label on the left or on

the right side.

Two rows of pad arrays on top and one rows bottom of pad arrays

on bottom are connected by line and can be used as a line for VIN,

GND, +5V, or other line.

Please refer to J10 and J11 jumper setting below to choose system

clock frequency source.

Jumper J10 & J11

Jumper J10 & J11Jumper J10 & J11

Jumper J10 & J11 Setting

Setting Setting

Setting

PIN 16/OSC1

PIN 16/OSC1 PIN 16/OSC1

PIN 16/OSC1 PIN 15/OSC2

PIN 15/OSC2PIN 15/OSC2

PIN 15/OSC2

PIN 16/OSC1

PIN 16/OSC1 PIN 16/OSC1

PIN 16/OSC1 PIN15/OSC2

PIN15/OSC2PIN15/OSC2

PIN15/OSC2

Please refer to TXD and RXD pad to connect the DT-PROTO 18 Pin

PIC

with computer through UART RS-232.

The Computer is connected to DT-PROTO 18 Pin PIC

with a

a a

“Sraight”,

“Sraight”, “Sraight”,

“Sraight”, here

herehere

here is the configuration:

is the configuration: is the configuration:

is the configuration:

Computer’s

Computer’s Computer’s

Computer’s

COM port DB9

COM port DB9COM port DB9

COM port DB9

DTDT

DT-

-PROTO 18 Pin PIC

PROTO 18 Pin PICPROTO 18 Pin PIC

PROTO 18 Pin PIC

®®

J5J5

RX (pin 2) RX (pin 5)

TX (pin 3) TX (pin 4)

GND (pin 5) GND (pin 3)

CD contents

CD contentsCD contents

CD contents

1. MPLAB IDE



2. I/O Testing software in Assembly language.

3. microcontroller Datasheet.

4. DT-PROTO 18 Pin PIC

manual.

5. Innovative Electronics Website.

Testing

Testing Testing

Testing software

softwaresoftware

software

The software which has been written to PIC16F84A (tes16f84.asm)

can be used as preliminary testing program. This software will

produce square wave to all I/O pins.

Testing steps:

- Connect a short between TXD and RXD.

- Plug in serial cable to computer's Com port and RJ11 DT-

PROTO 18 Pin PIC

- Plug in 9 VDC voltage source to VIN.

- Run SERTEST1.EXE. Select which COM port you are using and

press tes serial

tes serial tes serial

tes serial and follow the instruction on the screen.

- Square wave can be seen through oscilloscope, or connect it

to LED circuit or to DT

DTDT

DT-

-I/O LED Logic Tester

I/O LED Logic TesterI/O LED Logic Tester

I/O LED Logic Tester to see the LED

blinking.

Label

Pin 16/OSC1 and Pin

Pin 16/OSC1 and Pin Pin 16/OSC1 and Pin

Pin 16/OSC1 and Pin

15/OSC2

15/OSC2 15/OSC2

15/OSC2 are connected

are connectedare connected

are connected

to to

External Ceramic Resonator

External Ceramic Resonator External Ceramic Resonator

External Ceramic Resonator

4 MHz

4 MHz4 MHz

4 MHz

Pin 16/OSC1 and Pin

Pin 16/OSC1 and Pin Pin 16/OSC1 and Pin

Pin 16/OSC1 and Pin

15/OSC2

15/OSC2 15/OSC2

15/OSC2 are

areare

are

t t

connected to External

connected to External connected to External

connected to External

Ceramic Resonator 4

Ceramic Resonator 4Ceramic Resonator 4

Ceramic Resonator 4

Plug in RXD with the pin to receive serial data

Plug in TXD with the pin to send serial data

There was an error

There was an error There was an error

There was an error

on the PCB

on the PCBon the PCB

on the PCB

in which

in which in which

in which

ZTT20.0MX/ZTT20.0CV

ZTT20.0MX/ZTT20.0CVZTT20.0MX/ZTT20.0CV

ZTT20.0MX/ZTT20.0CV label

label label

label

should

shouldshould

should be

be be

be written

written written

written ZTT4.00MG

ZTT4.00MG ZTT4.00MG

ZTT4.00MG

and RB

and RB and RB

and RB label

label label

label should be written

should be written should be written

should be written RB5.

RB5.RB5.

RB5.

PROTO

VPP

VPPVPP

VPP

+5V

+5V+5V

+5V

GND

GNDGND

GND

PGD

PGDPGD

PGD

PGC

PGCPGC

PGC

Pin J9 allo

Pin J9 alloPin J9 allo

Pin J9 allo

cation

cationcation

cation

HEADER ICSP

HEADER ICSPHEADER ICSP

HEADER ICSP

RXD

TXD

GND

+5V

RXRX

TX TX

5 4 3 2

J1 J1

Front View

Front ViewFront View

Front View

GND

GNDGND

GND

Trademark & Copyright

Trademark & CopyrightTrademark & Copyright

Trademark & Copyright

- MPLAB IDE is copyright by Microchip Technology Incorporated.

- MPLAB, Microchip, and PIC are registered trademarks of Microchip

Technology Incorporated.

- ICSP and In-Circuit Serial Programming are trademarks of Microchip

Technology Incorporated.

♦ Thank you for your trust in our products, if you found any

difficulties, questions, or suggestions about this product,

please contact our technical support at:

support@innovativeelectronics.com

Innovative Electronics DT-PROTO User manual

Brand: Innovative Electronics

Model: DT-PROTO

Type: User manual

Download PDF

report

Innovative Electronics DT-PROTO User manual

Innovative Electronics DT-PROTO User manual

Other documents