Quick Reference Guide PP 3034
1
1 Unpack and installation the Printer
The printer PP 3034 is delivered in a package with the following label.
Note: Before unpacking the PP 3034 should be checked whether the specified mains voltage
corresponds to the local power supply. Otherwise, contact the supplier.
1.1 Delivery check for completeness
Please check the items from the following list to be exhaustive. If parts are missing or
damaged, notify your supplier.
The package includes:
– the PP 3034 (2)
– a power cord (3)
– a tear off bar (4)
– the Quick Reference Guide (5)
– an Image Cartridge (6)
Unpack the PP 3034
– remove the foam (1)
– remove the box incl.
position (3), (4) and (5)
– remove the Image Cartridge
After removing the plastic foil lift the printer (2) with two
persons using the transport grips (7) on the left and
right side of the printer (2) and put it onto a table.
1.2 Removing the transport locks
First remove the security
strip (8).
– push the latch (9) in direction of arrow and open the top cover.
– at the bottom left of the printer is an additional protective strip (10). Remove the strip
carefully.
Quick Reference Guide PP 3034
2
1.3 Installing the Image Cartridge
– Open the top cover.
– Unpack the Image Cartridge (1) and shake it
slowly.
– Remove both lock stripes (2) of the Image
Cartridge (1)
– Put the Image Cartridge (1) into the left and right guiding (3) and slide it to the bottom.
Note: The Image Cartridge is very
light sensitive. Do not expose
the Image Cartridge (1) to room
lighting or sunlight any longer
than necessary.
– Close the top cover.
1.4 Mounting the tear off bar
– Remove the two screws (7) on the back side of the printer.
– Position the tear off bar (4) as shown on the photo below and fix it with the included longer
screws.
1.5 Power ON/OFF Switch
– Make sure that the power switch of the printer is placed in the
O (OFF) (2) position.
– Connect the printer to the mains using the power cord (1).
Quick Reference Guide PP 3034
3
1.6 Connection to a Computer
The printer is equipped with a parallel IEEE 1284 and an Ethernet
10 Base T / 100TX interface. These are located at the rear of the printer.
Note: Make sure that the printer is powered off.
– Connect the printer according to the settings of the interface with the
Centronics or network cable.
– Check in the CONFIG. MENU the HOST CHANNEL.
– For the parallel connection the setting PARALLEL ONLY is
necessary.
– To activate the 10 Base T interface the setting must be I/O
EXTENSION (see Menu structure).
Note: For detail information about the Ethernet interface see the
included Ethernet Reference Manual.
1.7 Inserting fanfold paper
– Pull out and turn the knob (1) to the right (small paper) or left (wide paper) so that the
tractors (2) adjust to the approximate width of paper.
– Open the first part of the tractor covers (2), insert the paper up to the second tractor
and close one of the first tractor covers.
– Pull out the knob (1) again in the direction of the arrow and turn the knob (1) for the
fine adjustment. The pins of the tractor must be centred in the transport punches of the
paper.
– Close the other tractor (2).
Correct position of the tractor pins in the
transport punches.
Wrong position of the tractor
pins.
The paper is too tight!
Menu Structure
Note: To start the Menu Mode, press [ONLINE] and then press [MENU].
PAPER MENU
PAPER
n = 1 up to 50 PAPER LENGTH 2)
LENGTH FACTOR 2)
OFFLINE (n) IMAGE WIDTH 2)
TEAR OFF FORM SELECT PROFILE ORIENTATION
SELECT PROFILE 1 LANDSCAPE MODE
FEED N PAGES 2 ORIENT. MODE
SELECT FOLD : PAPER EXTENDED
CHANGE PROFILE 50 PAPER SELECTION
BASIC SETTINGS FUSER TEMP.
TEST MODE HUMIDITY
RESET PRINTER TONER DENSITY
CNG PROFILE n VER SHIFT
PAPER MENU HOR SHIFT
PCL MENU or 1) INIT LINE REG.
HEXDUMP MENU
GENERAL MENU PCL-MENU
or 1) FONT NUMBER
PITCH or
(n) = 1 up to 50 POINTSIZE 3)
SYMBOL SET
LINE SPACING
1) Depending on setting of TOP MARGIN 2)
EMULATION in LEFT MARGIN 2)
GENERAL MENU RIGHT MARGIN 2)
= PCL or HEXDUMP TEXT LENGTH 2)
PERF. SKIP 2)
2) Only displayed if PAPER $$ COMMANDS
In PAPER MENU
= CUSTOM HEXDUMP MENU
UEL COMMAND
3) Depending on selected FONT GENERAL MENU
EMULATION 1)
AUTO FORM FEED
AUTO TEAR OFF
TEAR OFF TIME
TEAR OFF SHIFT
PAPER RETRACT
BASIC SETTINGS
CONFIG.MENU CONFIG.-MENU
CLOCK MENU POWER SAVE
ALARM BELL
LANGUAGE
MENU ACCES
HOST CHANNEL
RECAL FACTORY
RESET TRU INFO
EXCHANGE TRU
CLOCK MENU
WEEKDAY
DAY
MONTH
YEAR
HOUR
MINUTE
SECOND
TEST MODE
TEST MENU TEST MENU
INFO MENU PANELTEST
SELF TEST
CONT. SELF TEST
CONFIG. PRINT
PCL-TYPE LIST
INFO MENU
PRINTER TYPE
ENGINE ID
FIRMWARE VERS.
CPC-FPGA VERS.
STACKER VERSION
IC INFO
TRU INFO
FUSER INFO
MACHINE COUNT
/