Aeg-Electrolux ELTC2000-5 Installation guide

Aeg-Electrolux
Brand
Aeg-Electrolux
Model
ELTC2000-5
Type
Installation guide

This manual is also suitable for

Aeg-Electrolux ELTC2000-5 is a microwave liftdoor for building-in, with a front width of 600 mm. The device is used for lifting and lowering the door of a microwave oven that is built into a kitchen cabinet. The liftdoor is mounted on the inside of the cabinet, and the door of the microwave oven is attached to the liftdoor. When the microwave door is opened, the liftdoor lifts the door up and out of the cabinet, making it easier to access the microwave. The liftdoor can be adjusted to different heights, depending on the size of the microwave oven and the cabinet.

Aeg-Electrolux ELTC2000-5 is a microwave liftdoor for building-in, with a front width of 600 mm. The device is used for lifting and lowering the door of a microwave oven that is built into a kitchen cabinet. The liftdoor is mounted on the inside of the cabinet, and the door of the microwave oven is attached to the liftdoor. When the microwave door is opened, the liftdoor lifts the door up and out of the cabinet, making it easier to access the microwave. The liftdoor can be adjusted to different heights, depending on the size of the microwave oven and the cabinet.

Page is loading ...
D Seite 3
F page 4
GB page 5
NL aijde 6
N side 7
I pagina 8
P pagina 9
S
DK
sida 10
sida 11
Publication no. 315 3592 06 - 2 - 03.10. RPA / AFA
Page is loading ...
Page is loading ...
GB Installation instructions.
Mikrowave-Liftdoor
Building-in fittings for front width 600
Assembly:
a)
b)
c)
Using the baseplate (G) as a template (nose of stop to the front !), mark the fixing holes
on both sides. (Fig. 4)
- Drill these approx. 2mm deep using a 2mm drilling bit.
- Now screw 1 wood screw (S 2) per side, in hole A up to approx. 5mm from the
wall (B).
- Now snap a left and right hand baseplate (G) on to both side plates.
- The 2nd baseplate (G) is required as an underlay if the niche is wider than
565mm.
Now insert the door (mounting) in the direction of the arrow between screw (A) and the
niche top. (Fig. 5)
- Take care that the mounting is flush up against the niche top (nose of stop) and
flush with the edge at the front.
- Now screw the mounting in place laterally using the 3 screws (S 2).
Now place the microwave unit in the niche with the required distance. (Fig. 6)
Right of alterations reserved.
Publication no. 315 3592 06 - 5 - 03.10. RPA/AFA
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Aeg-Electrolux ELTC2000-5 Installation guide

Aeg-Electrolux
Brand
Aeg-Electrolux
Model
ELTC2000-5
Type
Installation guide
This manual is also suitable for

Aeg-Electrolux ELTC2000-5 is a microwave liftdoor for building-in, with a front width of 600 mm. The device is used for lifting and lowering the door of a microwave oven that is built into a kitchen cabinet. The liftdoor is mounted on the inside of the cabinet, and the door of the microwave oven is attached to the liftdoor. When the microwave door is opened, the liftdoor lifts the door up and out of the cabinet, making it easier to access the microwave. The liftdoor can be adjusted to different heights, depending on the size of the microwave oven and the cabinet.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents