LG B18AWYNGMD.ANWBLAP Owner's manual
- Category
- Split-system air conditioners
- Type
- Owner's manual
This manual is also suitable for
OWNER’S MANUAL
AIR CONDITIONER
Please read this manual carefully before operating
your set and retain it for future reference.
www.lg.com
TYPE : CEILING CONCEALED DUCT
Original instruction
P/NO : MFL67902907
ENGLISH
2
TABLE OF CONTENTS
FOR YOUR RECORDS
Write the model and serial numbers here:
Model #
Serial #
You can find them on a label on the side of each unit.
Dealer's Name
Date Purchased
n Staple your receipt to this page in the event you need
it to prove date of purchase or for warranty issues.
READ THIS MANUAL
Inside you will find many helpful hints on how to use
and maintain your air conditioner properly. Just a little
preventive care on your part can save you a great deal
of time and money over the life of your air conditioner.
You'll find many answers to common problems in the
chart of troubleshooting tips. If you review our chart of
Troubleshooting Tips first, you may not need to call
for service at all.
PRECAUTION
• Contact the authorized service technician for repair or
maintenance of this unit.
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young
children or invalids without supervision.
• Young children should be supervised to ensure that
they do not play with the air conditioner.
• When the power cable is to be replaced, replacement
work shall be performed by authorized personnel only
using only genuine replacement parts.
• Installation work must be performed in accordance with
the National Electric Code by qualified and authorized
personnel only.
Safety Precautions.................3
Prior to Operation ..................6
Product Introduction..............7
Operating Instructions.........10
Maintenance and Service ....22
Before you Call
for Service ..........................24
Safety Precautions
3
ENGLISH
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions must be
followed.
n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified
by the following indications.
WARNING
CAUTION
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to properties only.
n Meanings of symbols used in this manual are as shown below.
Be sure not to do.
Be sure to follow the instruction.
WARNING
n Installation
Do not use a defective or
underrated circuit breaker. Use
this appliance on a dedicated
circuit.
• There is risk of fire or electric
shock.
For electrical work, contact the
dealer, seller, a qualified
electrician, or an Authorized
Service Center.
• Do not disassemble or repair the
product. There is risk of fire or
electric shock.
Always ground the product.
• There is risk of fire or electric
shock.
Install the panel and the cover
of control box securely.
• There is risk of fire or electric
shock.
Always install a dedicated
circuit and breaker.
• Improper wiring or installation
may cause fire or electric shock
Use the correctly rated breaker
or fuse.
• There is risk of fire or electric
shock.
Do not modify or extend the
power cable.
• There is risk of fire or electric
shock.
Do not install, remove, or re-
install the unit by yourself
(customer).
• There is risk of fire, electric shock,
explosion, or injury.
Be cautious when unpacking
and installing the product.
• Sharp edges could cause injury.
Be especially careful of the case
edges and the fins on the
condenser and evaporator.
For installation, always contact
the dealer or an Authorized
Service Center.
• There is risk of fire, electric shock,
explosion, or injury.
Do not install the product on a
defective installation stand.
• It may cause injury, accident, or
damage to the product.
Be sure the installation area
does not deteriorate with age.
• If the base collapses, the air
conditioner could fall with it,
causing property damage,
product failure, and personal
injury.
4
Safety Precautions
Do not store or use flammable
gas or combustibles near the
product.
• There is risk of fire or failure of
product.
Do not use the product in a
tightly closed space for a long
time.
• Oxygen deficiency could occur.
When flammable gas leaks,
turn off the gas and open a
window for ventilation before
turn the product on.
• Do not use the telephone or turn
switches on or off.
There is risk of explosion or fire
If strange sounds, or small or
smoke comes from product.
Turn the breaker off or
disconnect the power supply
cable.
• There is risk of electric shock or
fire.
Stop operation and close the
window in storm or hurricane.
If possible, remove the product
from the window before the
hurricane arrives.
• There is risk of property damage,
failure of product, or electric
shock.
Do not open the inlet grill of the
product during operation.
(Do not touch the electrostatic
filter, if the unit is so equipped.)
• There is risk of physical injury,
electric shock, or product failure.
When the product is soaked
(flooded or submerged),
contact an Authorized Service
Center.
• There is risk of fire or electric
shock.
Be cautious that water could
not enter the product.
• There is risk of fire, electric shock,
or product damage.
Ventilate the product from time
to time when operating it
together with a stove, etc.
• There is risk of fire or electric
shock.
Turn the main power off when
cleaning or maintaining the
product.
• There is risk of electric shock.
When the product is not be
used for a long time, turn off
the breaker.
• There is risk of product damage
or failure, or unintended
operation.
Take care to ensure that
nobody could step on or fall
onto the outdoor unit.
• This could result in personal injury
and product damage.
n Operation
Do not touch(operate) the
product with wet hands.
• There is risk of fire or electrical
shock.
Do not place a heater or other
appliances near the power
cable.
• There is risk of fire and electric
shock.
Do not allow water to run into
electric parts.
• It may cause There is risk of fire,
failure of the product, or electric
shock.
Do not let the air conditioner
run for a long time when the
humidity is very high and a
door or a window is left open.
• Moisture may condense and wet
or damage furniture.
Take care to ensure that power
cable could not be pulled out or
damaged during operation.
• There is risk of fire or electric
shock.
Do not place anything on the
power cable.
• There is risk of fire or electric
shock.
Do not turn on the breaker or power under
condition that front panel, cabinet, top
cover, control box cover are removed or
opened.
• Otherwise, it may cause fire, electric shock,
explosion or death.
5
ENGLISH
Safety Precautions
n Installation
CAUTION
Always check for gas (refrigerant)
leakage after installation or repair
of product.
• Low refrigerant levels may
cause failure of product.
Install the drain hose to ensure
that water is drained away
properly.
• A bad connection may cause
water leakage.
Keep level even when installing
the product.
• To avoid vibration or water
leakage.
n Operation
Do not install the product where the noise
or hot air from the outdoor unit could
damage the neighborhoods.
• It may cause a problem for your
neighbors.
Use two or more people to lift and
transport the product.
• Avoid personal injury.
Do not install the product where
it will be exposed to sea wind
(salt spray) directly.
•
It may cause corrosion on the product.
Corrosion, particularly on the condenser
and evaporator fins, could cause product
malfunction or inefficient operation
.
Do not expose the skin directly
to cool air for long periods of
time. (Don't sit in the draft.)
• This could harm to your health.
Do not use the product for special
purposes, such as preserving foods,
works of art, etc. It is a consumer air
conditioner, not a precision
refrigeration system.
• There is risk of damage or loss
of property.
Do not block the inlet or outlet
of air flow.
• It may cause product failure.
Use a soft cloth to clean. Do
not use harsh detergents,
solvents, etc.
• There is risk of fire, electric
shock, or damage to the plastic
parts of the product.
Do not touch the metal parts of the
product when removing the air
filter. They are very sharp!
• There is risk of personal injury.
Do not step on or put anyting
on the product. (outdoor units)
• There is risk of personal injury
and failure of product.
Always insert the filter securely.
Clean the filter every two weeks
or more often if necessary.
• A dirty filter reduces the efficiency of
the air conditioner and could cause
product malfunction or damage.
Do not insert hands or other objects
through the air inlet or outlet while the
product is operated.
• There are sharp and moving parts
that could cause personal injury.
Do not drink the water drained
from the product.
• It is not sanitary and could cause
serious health issues.
If the liquid from the batteries gets onto your skin
or clothes, wash it well with clean water. Do not
use the remote if the batteries have leaked.
• The chemicals in batteries could cause burns or
other health hazards.
If you eat the liquid from the batteries, brush your
teeth and see doctor. Do not use the remote if the
batteries have leaked.
• The chemicals in batteries could cause burns or
other health hazards.
Use a firm stool or ladder when
cleaning or maintaining the
product.
• Be careful and avoid personal
injury.
Replace the all batteries in the
remote control with new ones of
the same type. Do not mix old and
new batteries or different types of
batteries.
• There is risk of fire or explosion
Do not recharge or
disassemble the batteries.
Do not dispose of batteries in a
fire.
• They may burn or explode.
6
Prior to Operation
Prior to Operation
1. Contact an installation specialist for installation.
2. Use a dedicated circuit.
1. Being exposed to direct airflow for an extended period of time could be hazardous to your health.
Do not expose occupants, pets, or plants to direct airflow for extended periods of time.
2. Due to the possibility of oxygen deficiency, ventilate the room when used together with stoves or
other heating devices.
3. Do not use this air conditioner for non-specified special purposes (e.g. preserving precision
devices, food, pets, plants, and art objects). Such usage could damage the items.
1. Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling
sharp metal edges.
2. Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation,
leading to possible electric shock.
3. When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates
at a very high speed during operation. There is a possibility of injury if the unit’s power is
accidentally triggered on while cleaning inner parts of the unit.
For repair and maintenance, contact your authorized service dealer.
Preparing for operation
Usage
Cleaning and maintenance
Service
7
ENGLISH
Product Introduction
Product Introduction
1: Indoor unit
2: Outdoor unit
3: Remote controller
4: Inlet air
5: Discharge air
6: Refrigerant piping, connection
electric wire
7: Drain pipe
8: Ground wire
wire to ground outdoor unit to
prevent electrical shocks.
If your installation has a customized control system, ask your
LG dealer for the operation that corresponds to your system.
2
8
4
5
Remote
Controller
3
Air intake
vents
1
Air outlet
vents
6
7
Name and function of parts
What to do before operation
※Pictures may differ depending on the model.
※Pictures may differ depending on the model.
Product Introduction
8
Wired Remote Controller (Accessory)
h Display temperature can be different from actual room temperature if the remote controller is installed at the
place where sun-rays are falling directly or the place nearby heat source.
h The actual product can be different from above contents depending upon model type.
h When using simultaneous operation system, whenever press remote controller button, system will
approximately operate after 1~2 minutes.
NOTE
OPERATION INDICATION
SCREEN
SET TEMPERATURE BUTTON
FAN SPEED BUTTON
ON/OFF BUTTON
OPRATION MODE SELECTION
BUTTON
WIRELESS REMOTE
CONTROLLER RECEIVER
• Some products don't receive the
wireless signals.
AIR FLOW BUTTON
SUBFUNCTION BUTTON
FUNCTION SETTING BUTTON
VENTILATION BUTTON
RESERVATION
UP,DOWN,LEFT,RIGHT BUTTON
• To check the indoor temperature,
press button.
ROOM TEMPERATURE BUTTON
SETTING/CANCEL BUTTON
EXIT BUTTON
1
4
5
7
11
10
9
8
2
3
6
13
12
Please attach the inform label inside of the door.
Please choose proper language depend on your
country.
14
15
PQRCVSL0QW (white)
PQRCVSL0 (black)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
j Some functions may not be operated and displayed depending on the product type.
Product Introduction
9
ENGLISH
This air-conditioner is equipped with wired remote controller basically. But if you want to be available
with wireless remote controller, you pay for it.
Wireless Remote Controller (Accessory)
CAUTION
• Aim at the signal receiver on the wired remote controller so as to operate.
• The remote control signal can be received at a distance of up to about 7m.
•
Be sure that there are no obstructions between the remote controller and the signal
receptor.
• Do not drop or throw the remote controller.
• Do not place the remote controller in a location exposed to direct sunlight, or near the
heating unit, or any other heat source.
• Block a strong light over the signal receptor with a curtain or etc. so as to prevent the
abnormal operation. (ex:electronic quick start, ELBA, inverter type fluorescent lamp)
h
For more details refer to the Wireless Remote Control Accessory manual.
h
The actual product can be different from above contents depending upon model type.
h
The wireless remote controller does not operate When using simultaneous operation system.
NOTE
PQWRHQ0FDB
Operating instructions
10
Standard Operation - Standard Cooling
Standard Operation - Heating Mode
Operating instructions
Press button to turn on the
indoor.
1
Press button to select
Cooling operation mode.
2
Adjust the desired temperature
by pressing buttons.
Press button to check the
Room temperature.
When setting the desired
temperature higher than room
temperature, only ventilation
wind is blow out instead of
cooling wind.
3
h Setting Temp Range : 18˚C~30˚C (64˚F~86˚F)
It cools the room by comfortable and clean wind.
It supplies warm wind to the indoor
Press button to turn on the
indoor.
1
Press button to select
Heating mode.
(To check the indoor temperature,
press the room temperature button.)
2
Adjust the desired temperature
by pressing buttons.
When setting the desired
temperature lower than room
temperature, there is only
ventilation wind.
3
• Heating drive only operates at the cooling and heating model.
• Heating doesn't operate at cooling exclusive model.
Operating instructions
11
ENGLISH
Press button to turn on the
indoor.
1
Press button to select
Dehumidification mode.
The temperature setting can not be
adjusted during operation this mode.
2
Press the button to select
airflow rate weak → medium →
strong.
(The initial wind powerfulness of
humidity removal drive is 'weak'.)
3
It removes humidity while air-cooling weakly.
• In rainy season or high humidity climate, it is possible to operate simultaneously dehumidifier and
cooling mode to remove humidity effectively.
• The menu item of wind powerfulness might not be partially selected according to the product.
Standard Operation - Dehumidification Mode
Auto Changeover Mode
Repeat pressing button until
icon flash.
1
Press button to change.
❈ Converting temp value : 1~7
2
Press button to complete
and active the setting process.
3
Press button to exit or
system will automatically release
without any input after 25
seconds.
❈ When exiting without pressing
set button, the manipulated
value is not reflected.
4
Change temperature is the function to setup air-cooling and heating drive automatically changeable
according to the temperature at artificial intelligence drive mode.
Operating instructions
12
Press button to turn on the
indoor.
1
Press button to select
Artificial intelligence Mode.
2
You can adjust the
temperature as the
picture on the right
for cooling and
heating model.
3
For the case of
cooling exclusive,
as the picture on
the right, you can
adjust the
temperature from
hot to cold, from
"-2" to "2" based
on "00".
4
When cold
When cool
When appropriate
When warm
When hot
Standard Operation - Auto Operation Mode
During operating Auto Operation mode:
• We can use the FAN SPEED button
• We can change manually to other operation mode.
Press button to turn on the
indoor.
1
Press button to select Fan
Mode.
2
Every time pressing button, you
can select wind flow in order of
feeble → weak → medium → strong
→ automatic.
When running ventilation,
compressor of AHU doesn't work.
3
Standard Operation - Fan Mode
It blows the air as it is in the indoor, not the cold wind.
• Ventilation drive does not release cool wind but general fan
• Because it releases the wind that has no temperature difference from the room, it functions to
circulate the inside air.
• The menu item of wind powerfulness might not be partially selected according to the product.
Operating instructions
13
Standard Operation - Temperature Setting/Room Temperature Check
We can simply adjust the desired
temperature.
• Press the buttons to adjust the
desired temperature.
: Increase 1˚C or 2˚F per one time
pressing
: Decrease 1˚C or 2˚F per one time
pressing
Cooling operation:
- The cooling mode doesn't work if
desired temperature is higher than room
temperature Please lower the desired
temperature.
Heating operation:
- The heating mode doesn't work if desired
temperature is lower than room
temperature Please increase the desired
temperature.
1
Whenever press button, the room
temperature will be displayed within 5
seconds.
After 5 seconds, it turns to display the
desired temperature.
Because of location of remote controller,
the real room temperature and the this
displayed value can be different
1
Temperature Setting
Room Temperature Check
• For air-cooling drive, from 18°C to 30°C, and for heating drive, from 16°C to 30°C, you can select
desired temperature.
• 5°C is proper for the difference between room and outside temperature.
• Room temp: Indicate the current room
temperature.
• Set temp: Indicate the temperature that user
want to set.
h
Depend on what kind of controller, the desired
temperature can be adjusted at 0.5˚C or 1˚F.
ENGLISH
Operating instructions
14
It is the function to use preventing children or others from careless using.
Function setting - Child Lock
Press button repeatedly until
the is flashing.
1
If moving to 'setup' icon area by
using button, 'setup' icon
blinks, and child lock function is
setup if pressing button at
that time.
2
When cancelling lock function, if moving
to 'cancel' icon by pressing button
and then, pressing button, child lock
function is cancelled.
3
Press button to exit.
❈
After setup, it automatically gets out of setup
mode if there is no button input for 25 seconds.
❈
When exiting without pressing set button, the
manipulated value is not reflected.
4
Function Setting - Change Temp
Repeat pressing button until
icon flash.
1
Press button to change.
❈ Converting temp value : 1~7
2
Press button to complete
and active the setting process.
3
Press button to exit or system
will automatically release without any
input after 25 seconds.
❈
When exiting without pressing set button,
the manipulated value is not reflected.
4
Change temperature is the function to setup air-cooling and heating drive automatically changeable
according to the temperature at artificial intelligence drive mode.
Operating instructions
15
Function setting - Changing Current Time
Please press function setup
button. If pressing function setup
button repeatedly, it moves to
time setup menu. ‘Time setup’
icon is indicated at that time and date
blinks at current time indication area.
Ex) Changing Current Time as
'Monday / AM 10:20'.
1
Press key to adjust the current
day.
2
Press key to move to AM/ PM setting
mode (the 'AM/ PM segment will flash).
3
Setting AM/ PM value by
pressing button.
4
Press button to move to 'Hour'
setting mode. (the 'Hour' segment will
flash)
5
Setting Hour value by pressing
button.
6
ENGLISH
Operating instructions
16
Press button to move to 'Minute'
setting mode. (the 'Minute' segment will
flash)
7
Setting Minute value by pressing
button.
8
Press button to finish.
9
In the process, press
button to release and exit
from setting mode.
(In case of exit with
incomplete information, it will return to
the previous setting)
❈ When exiting without pressing set
button, the manipulated value is not
reflected.
10
Operating instructions
17
ENGLISH
Programming - Simple Reservation
Press button to enter the
Programming mode.
(the segment flashing)
Ex) Setting Simple Reservation
time as '3'.
1
Press button to adjust reservation
time.
2
Press button to finish setting.
3
Press button to exit.
❈ After setup, it automatically gets out of
setup mode if there is no button input
for 25 seconds.
❈ When exiting without pressing set
button, the manipulated value is not
reflected.
4
You can set the reservation conveniently in the units of 1 hour from 1 hour to 7 hours.
h When simple reservation setup, product automatically runs or stops after the time that is set.
Operating instructions
18
Programming : Weekly Reservation
Please move to 'weekly' by
repeatedly pressing reservation
button. 'Weekly' blinks at this time.
Please move to reservation setup mode by pressing reservation button.
❈ You can setup two weekly reservations for one day, and up to fourteen
reservations for a week.
For example, to setup (Tuesday morning 11:30 turned on ~ afternoon 12:30
turned off), you setup in order below.
2
1
Please select weekly reservation or
weekly reservation ¡ by using
button.
❈ You can setup two reservations,
weekly reservation 1 and weekly
reservation 2, for a day.
3
Please move to 'date' setup part by
using button. If 'date'
indication blinks, please setup date.
You can setup date from Monday to
Sunday.
4
Please move to 'AM/PM' setup part
of turning on by using button.
5
Please move to 'hour' setup part of
turning on by using button.
- It is the part to setup the time at
which air-conditioner is turned on.
6
Please move to 'minute' setup part of turning on by using button.
8
Please change time by using button.
- You can setup hour 0~12.
7
If 'minute' indication blinks, please setup 'minute' by using button
9
You can set the daily reservation in weekly unit.
Weekly reservation keeps operating until before you cancel it once you setup
Operating instructions
19
ENGLISH
Please move to 'AM/PM' setup part
of turning off by using button.
- AM/PM setup is identical with
turning on time setup.
10
Please move to 'hour' setup part
of turning off by using Right
button.
- It is the part to reserve the time
at which air-conditioner is
turned off.
- If 'hour' indication blinks, please
setup 'hour'.
❈
Please setup 'hour' and 'minute'
identically with the method to
setup turning on time.
11
If finishing weekly reservation setup, please press setup/cancellation button.
Weekly reservation setup for the day that you set is finished.
12
If you setup with the method identical with above by selecting the day that
you'd like to setup, it operates weekly reservation.
If you setup both turning on reservation time and turning off reservation time
identically, it doesn't operate reservation drive.
13
Weekly reservation explanation
Turning on time
Under bar: the indication that there is weekly reservation for
corresponding day
Reservation
number
Turning off time
h Indoor unit is turned on to desired temperature if it is configured using up/down button during
preset of weekly operation time. (Temperature selection range : 18℃~30℃)
- When desired temperature is not set, it is turned on automatically with desired temperature of
previous operation.
Operating instructions
20
Programming - Sleep Reservation
Press button to enter the
Programming mode.
Ex) Setting Sleep Reservation
time as '3'.
1
Repeat pressing button to enter the
SLEEP reservation setting mode.
( segment flashing)
2
Press button to adjust reservation
time.
The SLEEP reservation time is from 1 to
7 hours.
3
Press button to finish setting.
Whenever reservation is done.
4
Press button to exit.
❈ After setup, it automatically gets out of
setup mode if there is no button input
for 60 seconds.
❈ When exiting without pressing set
button, the manipulated value is not
reflected.
- If reservation is setup, 'sleep'
indication shows up at the lower part
of LCD screen.
5
If finishing sleep reservation setup,
air-conditioner product operates sleep
drive and stops after the time that is set.
6
Sleep reservation is the function of air-conditioner to run and stop after certain period of time at sleep
mode before sleep. When connected to a ventilation product and set the sleep reservation, when it
goes to the sleep mode, after the set time has elapsed.
Please reserve proper time at sleeping. (Too much air-cooling is not good for your health.)
• Because it automatically adjusts desired temperature for comfortable air-cooling at sleep drive,
there could be difference between remote controller's desired temperature and air-conditioner
body's desired temperature.
• Sleep reservation operates as off reservation for the product whose temperature adjustment isn't
controlled by unit of 0.5°C.
CAUTION
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
LG B18AWYNGMD.ANWBLAP Owner's manual
- Category
- Split-system air conditioners
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI