PowerLocus h-40-wireless User manual
- Category
- Power banks
- Type
- User manual
(1) Product Control and Connector Locations:
1- LED indicator
2- Multi-function button (power on / off, pairing, play / pause, auto
search radio)
3- Volume down (Long Press) / Last song (Short Press)
4- Volume up (Long Press)/Next song (Short Press)
5- MP3/FM
6- answer/end calls, reject call, last number redial
7- Micro SD/TF card slot
8- Micro USB charging port
9- Headset jack
10- Microphone
11- 3.5 stereo sound supply extension line (3ft, male to male)
12- Micro-B USB charging cable
(2) Powering the headset
• Power On: Press the mult-ifunction button for 2-3 seconds until the blue
indicator light flashes (the headset says: “The blue-tooth is ready to pair”).
• Power Off: Press the multi-function button for 2-3 seconds until the blue
indicator light goes off (the headset says: “The blue-tooth is powered off”).
(3) Pair to your mobile phone or other products
• Press the multi-function button for 2-3 seconds until the indicator light starts
flashing red and blue alternatively (the headset says: “The blue-tooth is ready to
pair”).
• Turn on the blue-tooth function of your connecting smart phone (or other
device).
• Search for the blue-tooth devices and select ’PowerLocus’. (Enter the code
‘0000’ if prompted)
• If paring is successful, the blue light indicator flashes (the headset says: “The
blue-tooth is connected successfully”).
• IMPORTANT: Please make sure the headphone is on before starting pairing
process.
• Headset will connect to the pre-set phone automatically when turned on (Please
check to be sure the blue-tooth functionality of your phone is “on”)
• If the pairing is not successful, please switch off headset first, and then attempt
to re-pair
(4) MP3 / FM
• In power-on mode, insert the MicroSD TF card (not included), short-press the
MP3/FM button, and the MP3’s will play automatically.
If no MicroSD TF card is installed, short-press the MP3/FM button; the FM radio
will then play automatically.
• In power-on mode, short-press the MP3/FM button 2 times. FM radio will play
automatically. Short-press the multi-function button to auto search all radio
stations. Pause, then short-press or . The radio station will play, and
the blue light flashes slowly.
• If you are listening FM radio, short-press MP3/FM button; it will be change to
blue-tooth mode and auto-connect your phone (or other device).
(5) Answer/End calls, reject calls, last number redial (In
blue-tooth mode)
• When there is a call, short-press the button to answer the call. After the call,
press the button to hang up. (If the other party hangs up first, no need press
the button)
• Reject call: long-press the button 2-3 seconds
• Last number redial: short-press the button 2 times
• When the phone call is answered, music will pause automatically and enter a
“waiting state”. After call is finished, the music will resume playing
automatically.
(6) Charging the headset
• Insert USB charging cable into the USB block. Connect the cable to a USB power
supply that provides 5VDC power (charging block not included). Connect
charging cable to the charging port of headset. When the red light is on, the
headset is in charging. When the red light is off, the headset is fully charged. It
takes 2 - 2.5 hours to fully charge the headset.
• The battery is rechargeable. Low-power indicator: When the alert tone “beeps”
and the indicator turns red, this indicates the battery has discharged and needs
to be charged. First time charging: please be sure the battery has been fully
charged before initial use.
(7) Wired headphone function
When blue-tooth connectivity is not available, connect one side of 3.5mm stereo
sound supply extension line to headphone audio jack. Connect the other side to the
audio jack of the playback device (such mobile phone, computer, ipad, MP3 players,
etc). Playback will start from the device.
(8)Precautions
1)Please be gentle when using the headphone.The Maximum tolerance of the button
is 250g.Excessive force or be stroked by something all will do damage to the
buttons.
2)Please do align the USB port when plug or pull USB cable in case that damage the
USB cable fail to charge the headphone.
3)When encounter something similar to interference,please at first delete the
Bluetooth devices that connected with headphone before,then restart your phone,at
last please repair with the Bluetooth headphone.
4)If long time without using headphone,it is recommended to turn off the
headphone,in case that the battery is in a low voltage state,causing the charging
problem.
5)Please do not put the headphone in the hot temperature area.
6)Please do not vibrate or shock the headphone violently, and do not let it fall down
from high place.
7)If there is no response of the headphone,please insert headphone plug hole reset
by tool.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
PowerLocus h-40-wireless User manual
- Category
- Power banks
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
