KitchenAid 720-0891R Owner's manual

720-0891B (LP) 730-0891B (NG)

720-0891R (LP) 730-0891R(NG)

19000473A1

FREESTANDING OUTDOOR GRILL

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-877-373-2301

or visit our website at www.Kitchenaidgrills.com

ASADOR AUTÓNOMO PARA EXTERIORES

Instrucciones de instalación y Manual de uso y cuidado

Para consultas respecto a características, funcionamiento, rendimiento, piezas, accesorios o servicio técnico, llame al: 1-877-373-2301

o visite nuestro sitio de internet en www.Kitchenaidgrills.com

COMPTOIR POUR GRIL D’EXTÉRIEUR

AUTOPORTANT

Instructions d’installation et Guide d’utilisation et d’entretien

Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces, des accessoires ou du service,

composer le: 1-877-373-2301

ou visiter notre site web www.Kitchenaidgrills.com

Table of Contents/Índice/Table des matières................................................................................. 2

Keep this manual for future reference.

Conserve el presente manual para consultas futuras.

Conserver ce manuel à titre de référence ultérieure.

OUTDOOR GRILL SAFETY………………………………3

INSTALLATION REQUIREMENTS………………………....5

Tools and Parts……………...…………………………………5

Location requirements…………………………………..…….5

Product Dimensions……………………………….………….6

Gas Supply Requirements……………………………………7

Gas Connection Requirements………………………………7

PACKAGE PARTS LIST…………………...……………9

INSTALLATION INSTRUCTIONS…………………….…...…11

Make Gas Connection…………………………...……..……24

GAS CONVERSION………………………………….............26

Tools and Parts for Gas Conversion …………………....26

Conversion from LP Gas to Natural Gas……………… ….26

Check and Adjust the burners………………………….……29

TABLE OF CONTENTS

OUTDOOR GRILL USE …………………………………………30

Using Your Outdoor Grill ………………………………..….…30

TIPS FOR OUTDOOR GRILLING ……………………….…..32

Cooking Methods ………………….………………………...….32

Grilling Chart ………………………….……………………....….33

OUTDOOR GRILL CARE …………………………………..…35

Replacing the Igniter Battery …….………………….………....35

General Cleaning ………………………………………..........…35

TROUBLE SHOOTING .........................................................37

ASSISTANCE ……………………………………………..……37

Accessories………………………………………………………..37

WARRANTY …………………………………………….…..…….38

REPLACEMENT PARTS……………………………………40

SÉCURITÉ DU GRIL D'EXTÉRIEUR ………………….……81

EXIGENCES D’INSTALLATION …………………………..83

Outils et pièces ……………...……………………………...….83

Exigences d'emplacement ……………………………………83

Dimensions du produit ……………………………………...…..84

Spécifications de l'alimentation en gaz ………………..……85

Exigences concernant le raccordement au gaz………………86

Liste des pièces de l'emballage…………………………….. 87

INSTRUCTIONS D’INSTALLATION ……………….……...….89

Raccordement au gaz …………………………............…..…102

CONVERSIONS POUR CHANGEMENT DE GAZ …….…..103

Outils et pièces pour conversion de gaz ………….……..…..103

Conversion de propane à gaz naturel ……………….…...….103

Contrôle et réglage des brûleurs ……………………….…106

TABLE DES MATIÈRES

UTILISATION DU GRIL D’EXTÉRIEUR …….…………..107

Utilisation du gril d’extérieur ………………………………107

CONSEILS POUR L'UTILISATION DU GRIL

D’EXTÉRIEUR……………………………………...……….…...109

Méthodes de cuisson ……………………………...…………109

Tableau de cuisson au gril ………………………...……...….110

ENTRETIEN DU GRIL D’EXTÉRIEUR ……………………..113

Remplacement de la pile de l’allumeur ………………………113

Nettoyage général …………………………………….……….113

DÉPANNAGE......................................................................115

ASSISTANCE……………………………………………….115

GARANTIE…………………………………………………...….116

PIÈCES DE RECHANGE …………………………………...118

ÍNDICE

SEGURIDAD DEL ASADOR PARA EXTERIORES….......42

REQUISITOS DE INSTALACIÓN…………..………………..44

Herramientas y piezas ……………...………………...……….44

Requisitos de ubicación ……………………………...……….44

Medidas del producto ……………………………….………45

Requisitos del suministro de gas ………………………….....46

Requisitos para la conexión de gas …………………...…….47

Lista de piezas del paquete………………………………….48

INSTRUCCIONES DE INSTALACIÓN ……………….……..50

Conexión del suministro de gas ………………………63

CONVERSIONES DE GAS ……………………………..….65

Herramientas y piezas para la conversión de gas ..........….65

Conversión de gas LP a gas natural …………………………65

Revise y regule los quemadores ……………………...……...67

USO DEL ASADOR PARA EXTERIORES …………………...69

Cómo usar el asador para exteriores …………………………..69

CONSEJOS PARA ASAR AL AIRE LIBRE …………………..71

Métodos de cocción ………………………………………...…...71

Cuadro para asar ……………………………………………...….72

CUIDADO DEL ASADOR PARA EXTERIORES ………….….74

Cómo reemplazar la batería del encendedor …………………74

Limpieza general ………………………………………………….74

SOLUCIÓN DE PROBLEMAS.................................................76

ASISTENCIA………………………………………………..……..76

GARANTÍA …………………………………………………..…....77

PIEZAS DE REPUESTO ……………………………...………79

2

OUTDOOR GRILL SAFETY

IMPORTANT: This grill is manufactured for outdoor use only. For grills that are to be used at elevations above 2,000 ft (609.6 m)

orifice conversion is required. See “ Gas Supply Requirements” section. It is the responsibility of the installer to comply with the

minimum installation clearances specified on the model/serial rating plate. The model/serial rating plate for freestanding models can

be found on the left-hand cabinet door.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from

the appliance and immediately call

your gas supplier or your fire

department.

WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

In the State of Massachusetts, the following installation instructions apply:

 Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed

by the State of Massachusetts.

 If using a ball valve, it shall be a T-handle type.

 A flexible gas connector, when used, must not exceed 3 feet.

3

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electrical shock,

Injury to persons, or damage when using the outdoor cooking

gas appliance, follow basic precautions, including the following:

 Do not install portable or built-in outdoor cooking gas

appliances in or on a recreational vehicle, portable

trailer, boat or in any other moving installation.

 Always maintain minimum clearances from

combustible construction, see “ Location

Requirements” section.

 The outdoor cooking gas appliance shall not be located

under overhead unprotected combustible construction.

 This outdoor cooking gas appliance shall be used only

outdoors and shall not be used in a building, garage, or

any other enclosed area.

 Keep outdoor cooking gas appliance area clear and

free from combustible material, gasoline and other

flammable vapors and liquids.

 Do not obstruct the flow of combustion and ventilation

air. Keep the ventilation openings of the cylinder

enclosure free and clear from debris.

 Open the cabinet door and inspect the gas cylinder supply

hose before each use of the outdoor cooking gas appliance.

If the hose shows excessive abrasion or wear, or is cut, it

MUST be replaced before using the outdoor cooking gas

appliance. Contact your dealer and use only replacement

hoses specified for use with the outdoor cooking gas

appliance.

 Visually check the burner flames.

They should be blue. Slight

yellow tipping is normal for

LP gas. The flames should

Be approximately 1" (2.5 cm) high.

 Check and clean burner/venturi tube for insects and

insect nest. A clogged tube can lead to fire under the

outdoor cooking gas appliance.

 The LP gas supply cylinder to be used must be:

- constructed and marked in accordance with the

Specification for LP Gas cylinders of the U.S.

Department of Transportation (DOT) or the

National Standard of Canada, CAN/CSA-b339,

Cylinders, Spheres, and Tubes for Transportation

of Dangerous Goods; and Commission.

- provided with a listed overfilling prevention device.

- provided with a cylinder connection device

compatible with the connection for outdoor cooking

gas appliances.

 Always check connections for leaks each time you

connect and disconnect the LP gas supply cylinder.

See “Installation Instructions” section.

 When the outdoor cooking gas appliance is not in

use, the gas must be turned off at the supply cylinder.

 Storage of an outdoor cooking gas appliance indoors

is permissible only if the cylinder is disconnected

and removed from the outdoor cooking gas appliance.

 Cylinders must be stored outdoors and out of the

reach of children and must not be stored in a

building, garage, or any other enclosed area.

 The pressure regulator and hose assembly supplied

with the outdoor cooking gas appliance must be

used. A replacement pressure regulator and hose

assembly specific to your model is available from

your outdoor cooking gas appliance dealer.

 Gas cylinder must include a collar to protect the

cylinder valve.

 For appliances designed to use a CGA791

Connection: Place a dust cap on cylinder valve

outlet whenever the cylinder is not in use. Only

install the type of dust cap on the cylinder valve

outlet that is provided with the cylinder valve. Other

types of caps or plugs may result in leakage of

propane.

If the following information is not followed

exactly, a fire causing death or serious injury may occur.

 Do not store a spare LP gas cylinder under or near

this outdoor cooking gas appliance.

 Never fill the cylinder beyond 80 percent full.

SAVE THESE INSTRUCTIONS

4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather these required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Location Requirements

Parts Supplied

■ Gas pressure regulator/hose assembly set for 11” WCP LP

gas

■ See “Package parts list”

 “AA” Battery (1)

 Natural gas orifice for main burner

Parts Needed

 20 lb LP gas fuel tank-approximately 18” (45.7cm) height.

Parts Needed for Conversion to Natural Gas

Natural gas conversion kit Part Number 710-0003. See

“Assistance” section to order. The conversion kit includes:

 Natural gas regulator 4" W.C. (marked “Natural Gas

Regulator”)

 10 ft (3.0 m) Natural gas hose with quick connector

 5.9" (150 mm) Natural gas regulator hose

 6 mm nut driver

 6 mm wrench

 Hex key

 Gas line shutoff valve

 1/2" male pipe thread nipple for connection to pressure

regulator.

 LP gas-resistant pipe-joint compound

 CSA design-certified outdoor flexible stainless steel

appliance connector (4-5 ft [1.2-1.5 m]) or rigid gas supply

line as needed.

Select a location that provides minimum exposure to wind

and traffic paths. The location should be away from strong

draft areas.

Do not obstruct flow of combustion and ventilation air.

Clearance to combustible construction for grill:

 A minimum of 24” (61 cm) must be maintained between

the front of the grill hood, sides and back of the grill

and any combustible construction.

 A 24” (61 cm) minimum clearance must also be

maintained below the cooking surface, and the grill

shall not be used under overhead combustible

construction.

5

Tools needed

 Phillip screwdriver

 Wrench or pliers

 Pipe wrench

 Noncorrosive leak-

detection solution

Product Dimension

6

The model/serial number rating plate is located on the inside of the

side panel. See the following illustration.

A .Model/serial number plate

A

IMPORTANT: Grill must be connected to a regulated gas supply.

Refer to the model/serial rating plate for information on the type

of gas that can be used. If this information does not agree with

the type of gas available, check with your local gas supplier.

Gas Conversion:

No attempt shall be made to convert the grill from the gas

specified on the model/serial rating plate for use with a different

gas type without consulting the serving gas supplier. The

conversion kit supplied with grill must be used. See “Gas

Conversions” section for instructions.

Gas Pressure Regulator

The gas pressure regulator supplied with this grill must be used.

The inlet (supply) pressure to the regulator should be as follows

for proper operation:

LP Gas:

Operating pressure: 11" (27.9 cm) WCP

Inlet (supply) pressure: 11" to 14" (27.9 cm to 35.5 cm) WCP

Natural Gas:

Operating pressure: 4" (10.2 cm) WCP

Inlet (supply) pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP

maximum.

Contact local gas supplier if you are not sure about the inlet

(supply) pressure.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with either the National Fuel Gas Code, ANSI

Z223.1/NFPA54, Natural Gas and Propane Installation Code,

CSA B149.1, Propane Storage And Handling Code, B149.2, or

the Standard for Recreational Vehicles, ANSI A119.2/NFPA

1192 and CSA Z240 RV Series Recreational Vehicle Code as

applicable.

Gas Supply Requirements

Burner Requirements for High Altitude

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level. Orifice

conversion is required. See “Assistance” section to order.

Gas Supply Line Pressure Testing

Testing above 1/2 psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):

The grill and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures greater than 1/2 psi (3.5 kPa).

Testing below 1/2 psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge)

or lower:

The grill must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than 1/2 psi (3.5 kPa).

Gas Connection Requirements

20 lb LP Gas Fuel Tank

This grill is equipped for use with a 20 lb LP gas fuel tank (fuel

tank not supplied). A gas pressure regulator/hose assembly is

supplied.

Any brand of 20 lb LP gas fuel tank is acceptable for use with

the grill, provided that it is compatible with the grill’s retention

means (tank tray included).

It is also design-certified by CSA International for local LP gas

supply or for Natural gas with appropriate conversion.

A. Gas pressure regulator/hose assembly

A

7

Natural Gas Conversion

Conversion must be made by a qualified gas technician. The

qualified Natural gas technician shall provide the Natural gas

supply to the selected grill location in accordance with the

National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition,

and local codes. For conversion to Natural gas, the Natural Gas

Conversion Kit supplied with the grill (on some models) or the

Natural Gas Conversion Kit Part Number 710-0003 must be

used. See “Assistance” section for information on ordering.

IMPORTANT: The gas installation must conform with local

codes, or in the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 - latest edition.

Follow instructions for converting to Natural gas in the “Gas

Conversions” section of this manual or the instructions supplied

with Natural Gas Conversion Kit Part Number 710-0003.

The gas supply line shall be equipped with an approved shutoff

valve. This valve should be located in the same area as the grill

and should be in a location that allows ease of opening and

closing. Do not block access to the shutoff valve. The valve is

for turning on or shutting off gas to the grill.

A. Gas supply line

B. Shutoff valve “open” position

C. To grill

8

Page is loading ...

Package parts List

14

16

17

11 12

15

x2

13

x2

10

A

x12

B x21

Hardware package list

Tools Needed

C

x32

D x16

Truss head screw

with locking washer

1/4" x 15mm

SUS Screw

5/32" x 10mm

Flat Washer

1/4"

Truss Head Screw

1/4" x 12mm

Some parts come with Screws pre-installed.

Loosen and tighten for final assembly.

11

ASSEMBLY INSTRUCTIONS

Page is loading ...

LP Gas:

IMPORTANT: A 20 lb LP gas fuel tank must be purchased

separately.

IMPORTANT: The gas pressure regulator/hose assembly

supplied with the grill must be used. Replacement gas pressure

regulator/hose assembly specific to your model is available from

your outdoor grill dealer.

To Connect the 20 lb LP Gas Fuel Tank:

1. Check that the 20 lb LP gas fuel tank is in the “Off”

position. If not, turn the valve clockwise until it stops.

2. Check that the 20 lb LP gas fuel tank valve has the proper

type-1 external male thread connections per ANSI Z21.81.

3. Check that the burner control knobs are in the “Off”

position.

4. Remove any debris and inspect the valve connections,

port, and gas pressure regulator/hose assembly for

damage.

NOTE: Always keep the LP cylinder at 90° (upright)

orientation to provide vapor withdrawal.

5. Using your hand, turn the gas pressure regulator/hose

assembly clockwise to connect to the 20 lb LP gas fuel

tank as shown.

Hand tighten only. Use of a wrench could damage the

quick coupling nut.

A. Gas pressure regulator/hose assembly

B. 20 lb LP gas fuel tank

A

B

Make sure that the cylinder valve connection device

properly mates with the connection device attached to

the inlet of the pressure regulator.

6. Open the tank valve fully by turning the valve

counterclockwise. Wait a few minutes for gas to move

through the gas line.

7. Before lighting the grill, test all connections by brushing

on an approved noncorrosive leak-detection solution.

Bubbles will show a leak.

8. If a leak is found, turn the tank valve off and do not use

the grill. Contact a qualified gas technician to make

repairs.

9. Go to “Check and Adjust the Burners” section.

24

Make Gas Connection

NOTE: If grill is to be converted to Natural gas, follow

instructions in the “Gas Conversions” section.

20 lb LP Gas Fuel Tank

To Disconnect the 20 lb LP Gas Fuel Tank:

1. Check that the burner control knobs are in the “Off” position

and the grill is cool.

2. Check that the 20 lb LP gas fuel tank is in the “Off” position.

If not, turn the valve clockwise until it stops.

3. Using your hand, turn the gas pressure regulator/hose

assembly counterclockwise to disconnect to the 20 lb LP gas

fuel tank as shown.

Hand loosen only. Use of a wrench could damage the quick

coupling nut.

A. Gas pressure regulator/hose assembly

B. 20 lb LP gas fuel tank

A

B

4. Place dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap on

the valve outlet that is provided with the cylinder valve.

Other types of caps or plugs may result in leakage of

propane.

25

GAS CONVERSIONS

Tools and Parts for Gas Conversion

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Parts supplied

 Natural gas orifices

Parts needed

Natural gas conversion kit Part Number 710-0003. See

“Assistance” section to order. The conversion kit includes:

 Natural gas regulator 4" W.C. (marked “Natural Gas

 Regulator”)

 10 ft (3.0 m) Natural gas hose with quick connector

 5.9" (150 mm) Natural gas regulator hose

 6 mm nut driver

 6 mm wrench

 Hex key

IMPORTANT: Gas conversions must be done by a qualified

installer. Before proceeding with conversion, shut off the gas

supply to the grill.

1. Turn off the main gas supply valve.

2. Disconnect 20 lb LP gas fuel tank (if present).

3. Turn off all burner control valves.

4. Remove the 20 lb LP gas fuel tank (if present) from

the grill cart.

5. Use an adjustable wrench to remove the LP regulator

from the manifold.

Conversion from LP Gas to Natural Gas

6. Use an adjustable wrench to install the Natural gas

regulator hose to the manifold and secure. Attach the

Natural gas regulator to the side panel inside the grill

cart with the two screws that are preassembled on the

regulator.

Tools needed

26

6mm

Change Grill Main Burner Valve Orifices

3. Use a 6 mm socket and wrench or 6 mm nut driver to

remove the brass orifice from the end of gas valve. The

main burner NG orifice is located behind the LP orifice, so

no additional orifice needs to be installed.

1. Remove the grates and flame tamers.

2. Remove the burner from the grill by lifting the burner out.

A

A. Main burner orifice

IMPORTANT: Check that the orifice is properly installed

inside of the burner opening.

4. Repeat the procedure for each main burner.

5. Position the igniters so they are 1/8" (3.2 mm) away

from each burner.

1.A combination of pipe fittings must be used to connect the

grill to the existing gas line.

 The 10 ft (3.0 m) PVC flexible gas supply hose design

certified by CSA must be used.

 Pipe-joint compounds suitable for use with Natural gas

must be used. Do not use Teflon®+ tape.

 There must be a certified manual shut-off valve in the gas

supply line near the grill for easy access.

2. Connect the brass connector on one end of the 10 ft (3.0 m)

PVC flexible gas supply hose to the Natural gas pressure

regulator.

3. Connect the quick connector on the other end of the

10 ft (3.0 m) PVC flexible gas supply hose to the rigid Natural

gas supply pipe.

Make Gas Connection

27

† ®TEFLON is a registered trademark of E.I. Du Pont De Nemours

and Company.

2. Use a flat-blade screwdriver to turn the high flame

setscrew counterclockwise approximate 90º.

3. Check that burner operates at the new high flame setting.

It may be necessary to adjust the screw setting slightly

more to get the ideal burner flame height.

Reattached the control knobs.

When converting from LP to Natural gas, you will need to

adjust the high flame setting screw for ideal burner flame

height.

1. Remove each control knob for the main burners.

28

In the last page of the Use and Care Guide, write “ Converted to

Natural Gas.” Also record the conversion date and the

technician/company that performed the conversion.

Note: Place LP gas parts in plastic parts bag for future use and

keep with pack containing literature.

Adjust High Flame Setting Screw

1. The appliance nameplate is located inside the grill cabinet on

the left –hand cabinet side. With a permanent marker, check

the box next to “Natural gas” and mark through “LP-Propane.”

Record Conversion

Check and Adjust the Burners

The burners are tested and factory-set for most efficient operation.

However, variations in gas supply and other conditions may make

minor adjustments to air shutter or low flame setting necessary. It is

recommended that a qualified person make burner adjustments.

Checking and adjusting the grill burner flames requires removing the

grates and flame tamers.

6. If flame is yellow (not enough air), turn air shutter

adjustment screw counterclockwise.

If flame is noisy or lifts away from burner (too much air),

turn air shutter adjustment screw clockwise.

Adjustment should be made clockwise or counterclockwise

from 1/8” (3.2 mm) to ¼” (6.4 mm).

7. Replace gas burner, sear plates and grates.

8. Light grill using information in the “Outdoor Grill Use” section.

See “Burner Flame Characteristics

If flame goes out on the “LOW” setting, the low flame setting must

be adjusted.

1. Turn off the valve and wait until grill and burners are cool.

2. Remove grill grates and flame tamers.

3. Light grill using information in the “Outdoor Grill Use” section.

4. Turn burner to its lowest setting.

5. Remove each control knob for the main burners by loosening

the setscrew with the hex key.

6. Hold valve stem with pliers and insert a small flat-blade

screwdriver into the shaft.

7. Watch the flame and slowly turn the screwdriver

counterclockwise.

8. Adjust flame to minimum stable flame.

A. Valve stem

B. Small flat-blade screwdriver

C. Pliers

A

B

C

The flames of the grill burners and side burners (on some models)

should be blue and stable with no excessive noise or lifting (LP gas

flames will have a slightly yellow tip). A yellow flame indicates not

enough air. If flame is noisy or lifts away from the burner, there is too

much air. Some yellow tips on flames when the burner is set to

HIGH setting are acceptable as long as no carbon or soot deposits

appear. The flames should be approximately 1" (2.5 cm) high.

Burner Flame Characteristics

Low Flame Adjustment

9. Replace the control knob and turn off the burner.

10. Repeat steps 3 through 9 for each burner if needed.

11. Replace the flame tamers and grates after the burners have

been cooled.

Check that burners are not blocked by dirt, debris, insect nests,

etc., and clean as necessary. If they are clean, adjust air shutters

as needed.

IMPORTANT: Before adjusting air shutters, let burners cool down

completely.

To Adjust:

1. Light grill using information in the “Outdoor Grill Use” section.

2. Observe flame to determine which burners need adjustment

and how the flame is acting.

3. Turn off the valve and wait until grill and burners cool

completely.

4. Remove grill grates and flame tamers.

5. Remove gas burner from the grill.

1” (2.5 cm)

29

OUTDOOR GRILL USE

A. Left grill burner knob B. Right grill burner knob

Inspect the gas pressure regulator/hose assembly before

each use.

1. Inspect the gas pressure regulator/hose assembly for

cuts, abrasions, or excessive wear.

2. If necessary, replace the gas pressure regulator/hose

assembly before using the grill.

Contact the dealer and use only replacement hoses

specified for use with the grill.

This manual covers several different models. The grill you have purchased may have some or all of the features listed. The locations

and appearances of the features shown here may not match those of your model.

Control Panel

Using Your Outdoor Grill

Inspect the LP Gas Fuel Tank Supply Hose

30

Main Burners

A B

Prepare the Grill for Lighting

1. For outdoor grills using a 20 lb LP gas fuel tank:

Slowly open the tank valve.

NOTE: If flow limiting device activates, your grill may not light.

If your grill does light, the flames will be low and will not heat

properly. Turn tank valve and all control knobs off and wait

30 seconds. After shutting off the tank, very slowly open tank

valve and wait 5 seconds before lighting.

2. For outdoor grills using gas supply source other than a 20 lb

LP gas fuel tank:

Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

Lighting the Grill Burners

Manually Lighting Grill Burners

4. Strike the match to light it.

5. Guide the lit match under the grill grate.

6. Push in and turn the burner knob to /HIGH for

the burner closest to the lit match. The burner will light

immediately. When burner is lit, turn knob to desired

setting.

7. Repeat steps 2 trough 6 for each main burner.

8. Remove match and replace manual lighting extension on

the right side panel.

IMPORTANT:

If burner does not light immediately, turn the burner knob to

OFF and wait 5 minutes before relighting.

If any burners do not light after attempting to light them

manually, contact the Customer Service Center. See the

“ Assistance” section.

1. Open the hood completely. Do not light burners with the hood

closed.

2. Make sure control knobs are turned to OFF. The Grease cup

must be in place and push all the way to back.

Turn the Gas Supply On

IMPORTANT: If burner does not light immediately, turn the

burner knob to OFF and wait 5 minutes before relighting.

1. Open the hood completely. Do not light burners with the

hood closed.

2. Do not lean over the grill.

3. Select the burner you want to light. Push in and turn the grill

burner control knob to /HIGH, while continuing to

hold it in.

4. You will hear the “snapping” sound of the spark. When

burner is lit, release the knob. Turn knob to desired setting.

5. Repeat for each of the other burners as needed.

1. Open the hood completely. Do not light burners with hood

closed.

2. Do not lean over the grill.

3. Remove the manual lighting extension (see following

illustration) and attach a match to the split ring.

A

A. Grease cup

A. Closed valve

B. Open valve

31

Direct Heat

Cooking by direct heat means the food is placed on grill

grates directly above lighted burners. Hood position can be

up or down. If hood is in the up position, total cooking times

may be longer.

Direct heat sears the food. Searing is a process that seals

natural juices in food by cooking with intense heat for a short

period of time. While juices stay inside, the outside is

browned with a flavorful grilled coating.

Cooking Methods

TIPS FOR OUTDOOR GRILLING

Before Grilling

 Thaw food items before grilling.

 Preheat grill on high (use all grill burners) 10 minutes. The

hood must be closed during preheating. Preheating provides

the high heat needed to brown and seal the juices.

 Shorten the preheat time when grilling high-fat cuts of meat

or poultry, such as chicken thighs. This will help reduce

flare-ups.

 Lightly oil the grill grates or the food when cooking low-fat

cuts of meat, fish or poultry, such as lean hamburger patties,

shrimp or skinless chicken breasts.

 Using too much oil can cause gray ash to deposit on food.

Trim excess fat from meats prior to cooking to reduce

flare-ups.

 Make vertical cuts at 2" (5 cm) intervals around the fat edge

of meat to avoid curling.

 Add seasoning or salt only after the cooking is finished.

Indirect Heat

For best results, do not select the indirect heat cooking

method when it is windy.

Cooking by indirect heat means the food is placed on

the grill grate above an unheated burner, allowing heat

from lighted burner(s) on either side to cook the food.

If possible, turn on 2 burners. Cook with the hood

down. This will shorten the cooking time.

32

 It may be necessary to lower the heat setting for foods that

cook a long time or are marinated or basted in a sugary sauce.

 If using a high flame, add barbecue sauce only during the last

10 minutes of cooking to avoid burning the sauce.

 The degree of doneness is influenced by the type of meat, cut

of meat (size, shape and thickness), heat setting selected, and

length of time on the grill.

 Cooking time will be longer with an open grill cover.

During Grilling

 Turn foods only once. Juices are lost when meat is turned

several times.

 Turn meat just when juices begin to appear on the surface.

 Avoid puncturing or cutting the meats to test doneness. This

allows juices to escape.

 Knobs have High, Medium and Low settings for flame

adjustment.

 Heat settings indicated are approximate.

 Grilling times are affected by weather conditions.

 When 2 temperatures are listed, for example: Medium to Medium-

Low, start with the first and adjust based on cooking progress.

 Cooking times may vary from chart times depending on the type of

fuel, Natural or LP gas.

FOOD COOKING METHOD/

BURNER SETTING

INTERNAL TEMP. TIME

(total minutes)

SPECIAL INSTRUCTIONS

Beef

Hamburgers ½" (1.3 cm) to

¾

"

(1.9 cm) thick

DIRECT

Medium

Medium (160°F/71°C)

10-15 Grill, turning once.

Roasts

Rib Eye, Sirloin

INDIRECT

Medium/OFF/Medium

Med-Rare (145°F/63°C)

to Medium (160°F/71°C)

32-40 per lb

(12-15 per kg)

Tent with foil first 45-60

minute; of cooking time.

Steaks, 1" (2.5 cm)

Porterhouse, Rib, T-bane, Top

Loin, Sirloin

DIRECT Medium

Med-Rare (145°F/63°C)

to Medium (160°F/71°C)

11-16 Rotate steaks Vi turn to

create criss-cross grill marks.

Steaks, 1½" (3.8 cm)

Porterhouse, Rib, T-bane, Top

Loin, Sirloin

DIRECT Medium

Med-Rare (145°F/63°C)

to Medium (160°F/71°C)

18-25

Top Round or Shoulder/

Chuck (London Broil) 1½" (3.8

cm) thick

DIRECT Medium

Med-Rare (145°F/63°C)

to Medium (160°F/71°C)

22-29

Flank, ½" (1.3 cm) thick DIRECT Medium

Med-Rare(145°F/63°C)

11-29

Pork

Chops,

1" (2.5 cm)

1½ " (3.8 cm) thick

DIREC

T Medium to Med-Low

Medium (160°F/71 °C)

12-22

30-40

Ribs

2½-4 lbs (0.9-1.5 kg)

INDIRECT

Med/OFF/Med

Medium (160°F/71 °C)

40-60 Grill, turning occasionally.

During last few minutes brush

with barbecue sauce if desired.

When done, wrap in foil.

Roast, boneless tenderloin,

1lb (0.37 kg)

DIRECT

Medium

Medium (160°F/71 °C)

18-22 Turn during cooking to brown

on all sides.

Ham halt,

8-10 lbs (3-3.7 kg)

INDIRECT

Med/OFF/Med

Reheat (140°F/60°C)

2-2½ hours Wrap entire ham in foil and put

on grill without pan or drip pan

Ham steak precooked,

½” (1.3 cm) thick

DIRECT

Preheat Medium

Grill Medium

Reheat (145°F/63°C)

7-10

Hot Dogs

DIRECT

Medium

Reheat (145°F/63°C)

5-10 Slit skin if desired.

Chicken

Breast, boneless

DIRECT

Medium

170°F/77°C

15-22

For even cooking, pound

breast to ¾" (2.0 cm) thick.

Pieces, 2-3 lbs (0.75-

1.1 kg)

DIRECT

Med-Low to Medium

Breast 170°F/77°C

Thigh 180°F/82°C

Start bone side down.

Lamb

Chops and Steaks, Loin, Rib,

Sirloin, 1" (2.5 cm) thick

DIRECT

Medium

Med-rare (145°F/63°C)

to Medium (160°F/71°C)

10-20

1½" (3.8 cm) thick DIRECT

Medium

Med-rare (145°F/63°C)

to Medium (160°F/71°C)

16-20

Grilling Chart

33

Page is loading ...

KitchenAid 720-0891R Owner's manual

KitchenAid 720-0891R Owner's manual

in other languages

Related papers

Other documents