AEG DI7490-M User manual

DI7490-M

LIBRETTO ISTRUZIONI

USER MANUAL

BEDIENUNGSANLEITUNG

ИНСТРУКЦИЯ ПО МОНТАЖУ И

ЭКСПЛУАТАЦИИ

INSTRUKCJA OBSŁUGI I INSTALACJI

БУКЛЕТ

KULLANIM VE MONTAJ TALIMATLARI

IT

EN

DE

RU

PL

UK

TR

CAPPA

COOKER HOOD

DUNSTABZUGSHAUBE

ВЫТЯЖКA

OKAP KUCHENNY

КАПОТ

DAVLUMBAZ

3

15

27

39

51

63

75

Page is loading ...

CARATTERISTICHE

6

CARATTERISTICHE

Ingombro









Page is loading ...

FOR PERFECT RESULTS

Thank you for choosing this AEG product. We have created

it to give you impeccable performance for many years, with

innovative technologies that help make life simpler – featu-

res you might not find on ordinary appliances. Please spend

a few minutes reading to get the very best from it.

ACCESSORIES AND CONSUMABLES

In the AEG webshop, you’ll find everything you need to keep

all your AEG appliances looking spotless and working per-

fectly. Along with a wide range of accessories designed and

built to the high quality standards you would expect, from

specialist cookware to cutlery baskets, from bottle holders to

delicate laundry bags…

Visit the webshop at:

www.aeg-electrolux.com/shop

16

CONTENTS

17

18

20

24

25

Recommendations And Suggestions

Characteristics

Installation

Use

Maintenance

Contents

RECOMMENDATIONS AND SUGGESTIONS

17

RECOMMENDATIONS AND SUGGESTIONS

The Instructions for Use apply to several versions of this appliance. Accordingly, you

may find descriptions of individual features that do not apply to your specific appli-

ance.

INSTALLATION

• Themanufacturerwillnotbeheldliableforanydamagesresultingfromincor-rector

improper installation.

• Theminimumsafetydistancebetweenthecookertopandtheextractorhoodis650mm

(some models can be installed at a lower height, please refer to the paragraphs on work-

ing dimensions and installation).

• Checkthatthemainsvoltagecorrespondstothatindicatedontheratingplatefixedto

the inside of the hood.

• ForClassIappliances,checkthatthedomesticpowersupplyguaranteesadequateearth-

ing.

 Connecttheextractortotheexhaustfluethroughapipeofminimumdiameter120mm.

The route of the flue must be as short as possible.

• Donotconnecttheextractorhoodtoexhaustductscarryingcombustionfumes(boilers,

fireplaces, etc.).

• Iftheextractorisusedinconjunctionwithnon-electricalappliances(e.g.gasburning

appliances), a sufficient degree of aeration must be guaranteed in the room in order to

prevent the backflow of exhaust gas. The kitchen must have an opening communicating

directly with the open air in order to guarantee the entry of clean air.

USE

• Theextractorhoodhasbeendesignedexclusivelyfordomesticusetoeliminatekitchen

smells.

• Neverusethehoodforpurposesotherthanforwhichithasbendesigned.

• Neverleavehighnakedflamesunderthehoodwhenitisinoperation.

• Adjusttheflameintensitytodirectitontothebottomofthepanonly,makingsurethat

it does not engulf the sides.

• Deepfatfryersmustbecontinuouslymonitoredduringuse:overheatedoilcanburstinto

flames.

• Donotflambèundertherangehood;riskoffire

• Thisapplianceisnotintendedforusebypersons(includingchildren)withreducedphysi-

cal, sensory or mental capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the appliance by a person re-

sponsible for their safety.

• Childrenshouldbesupervisedtoensurethattheydonotplaywiththeappliance.

MAINTENANCE

• Switchofforunplugtheappliancefromthemainssupplybeforecarryingoutanymain-

tenance work.

• Cleanand/orreplacetheFiltersafterthespecifiedtimeperiod(Firehazard)

• Cleanthehoodusingadampclothandaneutralliquiddetergent.

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be

handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed

of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be

caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your

local city office, your household waste disposal service or the shop where you purchased the product.

CHARACTERISTICS

18

CHARACTERISTICS

Dimensions









CHARACTERISTICS

19

Components

Ref. Q.ty Product Components

1 1 Hood Canopy complete with: Controls, Lights,

Filters

2 1 Telescopic chimney made up of:

2.1 1 Upper chimney

2.2 1 Lower chimney

7.1 1 Telescopic frame complete with Suction fan,

made up of:

7.1a 1 Upper frame

7.1b 1 Lower frame

9 1 Reductionflangeø150-120mm

10 1 Damperø150

14.1 2 Air Outlet Connector Extension

15 1 Air Outlet Connector

24 1 Connection box

25 2 Hose clamps (not included)

Ref. Q.ty Installation Components

7.3 1 Air Outlet Connector fixing bracket

11 4 WallPlugsø10

12c 8 Screws 2,9 x 6,5

12e 4 Screws 2,9 x 9,5

12f 2 ScrewsM4x80

12g 4 ScrewsM6x80

12h 4 Screws5,2x70

12q 4 Screws 3,5 x 9,5

21 1 Drilling template

22 8 6.4 mm int. dia washers

23 4 M6 nuts

Q.ty Documentation

1 Instruction Manual





























































INSTALLATION

20

INSTALLATION

Drilling the Ceiling/shelf and fixing the frame

• Useaplumblinetomarkthecentreofthehobontheceiling/supportshelf.

• Placethedrillingtemplate21 provided on the ceiling/support shelf, making sure that the tem-

plate is in the correct position by lining up the axes of the template with those of the hob.

• Markthecentresoftheholesinthetemplate.

• Drilltheholesatthepointsmarked:

• Forconcreteceilings,drillforplugsappropriatetothescrewsize.

• Forhollowbrickceilingswithwallthicknessof20mm:drillø10mm(immediatelyinsertthe

Dowels 11 supplied).

• Forwoodenbeamceilings,drillaccordingtothewoodscrewsused.

• Forwoodenshelf,drillø7mm.

• Forthepowersupplycablefeed,drillø10mm.

• Fortheairoutlet(DuctedVersion),drillaccordingtothediameteroftheexternalairexhaust

duct connection.

• Inserttwoscrewsofthefollowingtype,crossingthemandleaving4-5mmfromtheceiling:

• Forconcreteceilings,usetheappropriateplugsforthescrewsize(notprovided).

• forCavityceilingwithinnerspace,withwallthicknessofapprox.20mm,Screws12h, sup-

plied.

• Forwoodenbeamceilings,use4woodscrews(notprovided).

• Forwoodenshelf,use4screws12g with washers 22 and nuts 23, provided.

INSTALLATION

21

FIXING THE FRAME

• Loosenthetwoscrewsfasteningthelowerchim-

ney and remove this from the lower frame.

• Loosenthetwoscrewsfasteningtheupperchim-

ney and remove this from the upper frame.

Ifyouwishtoadjusttheheightoftheframe,proceed

as follows:

• Unfasten the metric screwsjoining the two col-

umns, located at the sides of the frame.

• Adjusttheframetotheheightrequired,thenre-

place all the screws removed as above.

• Insert the upper chimney stack fromabove, and

leave it running free on the frame.

• Lift up the frame, fit  the frame slots onto the

screws up to the slot end positions.

• Tightenthetwoscrewsandfastentheothertwo

screws provi-ded with the hood.

Before tightening the screws completely it is possible

toadjusttheframebyturningit.Makesurethatthe

screws do not come out of their seats in the slotted

holes.

• Theframemountingsmustbesecuretowithstand

the weight of the hood and any stresses caused by

the occasional side thrust applied to the device.

On completion, check that the base is stable, even

iftheframeissubjectedtobending.

• Inallcaseswheretheceilingisnotstrongenough

at the suspension point, the installer must provide

strengthening using suitable plates and backing

pieces anchored to the structurally sound parts.





INSTALLATION

22

CONNECTION IN DUCTING VERSION

When installing the ducting version, connect the

hood to the chimney using either a flexible or rigid

pipe ø 150 or 120 mm, the choice of which is left

to the installer.

To install a ø 150

• Toinstallthedumper10.

• Fixthepipeinpositionusingsufficientpipeclamps

(not supplied).

To install a ø 120

• Toinstallaø120mmairexhaustconnection,insert

the reducer flange 9 on the dumper 10.

• Fixthepipeinpositionusingsufficientpipeclamps

(not supplied).

• Removeanyactivatedcharcoalfilters.

CONNECTION IN RECYCLING VERSION

• InserttheConnectorextensions14.1intothesideof

the Connector 15.

• InserttheConnector15intotheSupportbracket7.3

and fix it with the screws.

• FastentheSupportbracket7.3,fixingittotheupper

part with the Screws.

• Make sure that the Connector extensions outlet

14.1 is in correspondence with the Chimney open-

ings both horizontally and vertically.

• Join the Connector15totheHoodcanopyoutlet

usingarigidorflexiblepipeø¸150mm,selectionof

which is at the discretion of the installation techni-

cian.

• MakesurethattheActivatedcharcoalodourfilter

has been fitted.

























INSTALLATION

23

FLUE ASSEMBLY - MOUNTING THE HOOD BODY

• Position the upper chimney section and fix the

upper part to the frame using the 2 screws 12c

(2,9 x 6,5) provided.

• Similarly,positionthelowerchimneysectionand

fix the lower part to the frame using the 2 screws

12c (2,9 x 6,5) provided.

Before fixing the hood body to the frame:

• Screwthe2screws12f half way into the holes

provided in the sides of the bottom of the frame.

• Removethegreasefiltersfromthehoodcanopy.

• Removeanyactivatedcharcoalfilters.

• Liftthehoodcanopyandengagethescrews12f

in the slots (A) as far as they will go.

• Workingfrombelow,fixthehoodcanopytothe

frame (B), using the 4 screws 12q and 4 washers

22 provided, then tighten all the screws securely.

ELECTRICAL CONNECTION

• Connect the hood to the mainsthrougha two-

pole switch ha-ving a contact gap of at least 3

mm.

• Removethegreasefilters(seeparagraphMainte-

nance) being sure that the connector of the feed-

ing cable is correctly inserted in the socket placed

on the side of the fan.

• ConnectthecontrolconnectorCmd.

• ConnectthelightsconnectorLux.

• Placetheconnectorsinthejunctionbox24 and

close it using the 2 screws 12e (2,9 x 9,5) pro-

vided.

• Fixthejunctionboxtothehoodbodyusingthe2

screws 12c (2,9 x 6,5) provided.

• Fortherecirculationversion,fittheactivatedcar-

bon odour fil-ter.

• Replacethegreasefilters.























USE

24

USE

BUTTON DISPLAY FUNCTIONS

A Displays the set speed Turns the suction motor on and off

B Displays the set speed Decreases the speed of the motor V3 V2 V1

C Displays the set speed Increases the speed of the motor V1 V2 V3

D Displays HI The spot flashes Starts maximum suction speed. After 5 minutes the speed will return

automatically to the one set before. This function can be deactivated

by pressing the button again (the decimal point at the centre of the

display will flash).

E Displays the time remaining before

the hood turns off (countdown)

and the Set speed. The spot at the

bottom right flashes

Enables automatic delayed shutdown of the appliance (Delay), with a

delay that depends on the working speed set.

Speed1 delay20 minutes

Speed 2 delay 15 minutes

Speed3 delay10minutes

The proposed delay time can be changed by pressing the button succes-

sively and selecting one of the options available (5, 10, 15, 20, 25 and

30minutes).Attheendofthetimeselectedtheappliancewillturnoff

automatically. To deactivate this function, simply press the button until

theoption selectedis 0 or turn the motor off.

F Turns the hob lighting system on and off

Displays F Indicates the need to wash the metal grease filters. The alarm is triggered

aftertheHoodhasbeeninoperationfor100workinghours.Thisindication

is only visible when the motor is turned off. To reset the alarm:

Turn the motor off and press button D for approximately 3 seconds,

until the display turns off.

Displays C Indicates the need to change the activated charcoal filters, and also to

wash the metal grease filters. The alarm is triggered after the Hood has

been in operation for 200 working hours. This indication is only visible

when the motor is turned off. This indication must be activated following

the procedure described in the section on maintenance of the activated

charcoal filter. To reset the alarm:

Turn the motor off and press button D for approximately 3 seconds,

until the display turns off.

     

MAINTENANCE

25

MAINTENANCE

Metasletal grease filters

Filters can be washed in the dish machine. They need to

be washed when F-sign appears on the display or in any

case every 2 months, or even more frequently in case of

particularly intensive use of the hood.

Alarm reset

• Switch off the hood and thelights.

• Pressthe D-key till the display is unlit.

Cleaning the filters

• Removethefiltersonebyonepushingthemtowardsthe

back side of the hood unit and simultaneously pulling

downwards.

• Any kind of bending of the filters has to be avoided

when washing them. Before fitting them again into

the hood make sure that they are completely dry. (The

colour of the filter surface may change through-out the

time but this has no influence to the filter efficiency).

• When fitting the filters into the hood pay attention

that they are mounted in correct position the handle

facing outwards.

MAINTENANCE

26

Charcoal filter (recycling version)

This filter cannot be washed or regenerated. It must be replaced when the C appears on the display or

at least once every 4 months. The filter saturation alarm has to be activated already before.

Activation of the alarm signal

• In RecirculationVersionHoods,theFilterSaturationAlarmmust be activated oninstallation or at a

later date.

• Pressandhold button E (Delay) for 5 seconds, until confirmation appears on the display:

 • Cflashestwice– Activated CharcoalFiltersaturation alarmACTIVATED.

 • Cflashesonce– Activated CharcoalFiltersaturation alarmDEACTIVATED.

Replacing the charcoal filter

Reset of the alarm signal

• Switch off the hood andthelighting.

• PresstheD-key until the display is unlit.

Replacing of the filter

• Remove the metal greasefilters.

• Remove the saturatedcharcoal filterbyreleasing the

fixing hooks

• Fit the new filter andfastenitin its correctposition.

• Put the metal greasefiltersintheir seats.

Lighting

LIGHT REPLACEMENT

20 W halogen light.

• Remove the 2 screwsfixing the Lighting support, and

pull it out of from the Hood.

• Extractthelamp from theSuppor.

• Replace with another of thesametype,making sure

that the two pins are properly inserted in the lamp

holder socket holes.

• Refit the Support, fixing itinplacewith the two

screws removed as above.

Page is loading ...

CHARAKTERISTIKEN

30

CHARAKTERISTIKEN

Platzbedarf









Page is loading ...

www.aeg-electrolux.com/shop

436005006_05- 110518

AEG DI7490-M User manual

AEG DI7490-M User manual

in other languages

Related papers

Other documents