Magnat Audio MULTIMEDIA 2100 DIGITAL Owner's manual

Brand: Magnat Audio

Model: MULTIMEDIA 2100 DIGITAL

Category: Speaker sets

Type: Owner's manual

Page is loading ...

Dear MAGNAT Customer,

Congratulations on your fine new loudspeakers and thank you very much for choosing MAGNAT! You

have made an excellent choice. The high-quality speakers produced by MAGNAT are renowned all over

the world.

Please study the instructions and information below carefully before using your new loudspeakers.

IMPORTANT SAFETY PRECAUTIONSPlease read through the instruction manual carefully before

starting to use the device. This manual contains important information concerning operation

and safety aspects. It is imperative you observe all of the information. Keep the manual in a safe

location.

• WARNING NOTICES: All of the warning symbols on the speakers, accessories and in the instruction

manual itself must be adhered to.

• EXPOSURE TO HEAT: Only operate the speakers and accessories in a temperature range from

10°C to 40°C.

• The speakers should not be positioned near heat sources (heaters, ovens, radiant heaters, naked

flames, etc.). When setting up close to an amplifier a minimum distance of 10 cm must be maintained.

The distance between the active subwoofer enclosure and the walls of the room or other objects

(e. g. furniture, shelf units) may not be less than 5 cm on any side.

• The aluminium plate and cooling fins of the amplifier at the rear of the active subwoofer serve to cool

the built-in amplifier; for this reason, they must also be at least 5 cm away from all objects and must

not be covered (e.g. by a curtain).

• EFFECT OF MOISTURE: The speakers should not be exposed to dripping or splash water. Neither

should they be used to support vases or other containers filled with liquid. Do not expose the speakers

to water or high levels of humidity. There is a danger of electric shock. In the event of contact with

moisture or liquids remove the mains adapter immediately.

• FOREIGN MATERIAL: Ensure that no foreign material enters through the speaker openings and into

the interior. This could trigger short circuits and even result in electric shock and fire.

• CLEANING: Please use a soft, dry cloth with no cleaning agents, sprays or chemical solvents, as

these could damage the surfaces.

• ELECTRICAL CONNECTION: Please note the voltage levels on the information sign. The mains

adapter for the speakers should only be operated with the voltage and frequency values specified

on the sign.

• LIGHTNING PROTECTION/PREVENTIVE MEASURES: If the device is not going to be used for a

prolonged period (e.g. when on holiday), it should be disconnected from the mains by removing the

plug. The device should also be disconnected from the mains in the event of a thunderstorm. Doing

this will prevent damage caused by lightning and overvoltage.

• MAINS CABLE: The mains cable must always be suitable for operation and it should only ever be laid

out in a manner that prevents it from being trodden on. It should not be pinched by objects either, as

this can damage the cable. When using plugs and power strips it must be ensured that the cable is

not kinked at the point where it emerges from the socket. Do not connect or remove the mains cable

with damp hands.

• OVERLOAD: Sockets, power strips and extension cables should not be overloaded. If an overload

occurs, there is a risk of electric shock and fire.

• SETTING UP: Please read the installation instructions. If you want to mount the speakers on the wall,

follow the description in the installation instructions.

• The speakers should only be positioned or mounted on a solid surface and not on moving base

frames, otherwise there is a risk of injury.

• Repairs must always be conducted by qualified specialists, as you might otherwise be exposed to

dangerous high voltage levels or other hazards.

The triangle with a lightning symbol warns the user that high voltage is used within the device

which can result in electric shock.

The triangle with an exclamation mark informs the user that important operating and

maintenance instructions (repair) are contained in the accompanying instruction manual, which

must be observed.

DO NOT OPEN! RISK OF ELECTRIC SHOCK!

CAUTION: In order to avoid electric shock do not open the speaker

housing/mains adapters or remove the covers. The user is not to conduct

any repairs him/herself. Repairs should only be conducted by qualified

technicians! Do not use any sockets or extension cables that do not fully

accommodate the plug of the device.

INSTRUCTIONS FOR DISPOSAL

In accordance with European Directive 2002/96/EC all electrical and electronic appliances must be dis-

posed of separately via local collection points. Please observe the local regulations and do not dispose

of your old appliances with normal household waste.

Battery disposal

Old batteries are hazardous waste and must be disposed of in accordance with current regulations.

CONTENTS

(A) 2 pcs. Satellite speakers

(B) 1 pc. Subwoofer with built-in amplifier

(D) 1 pc. Remote control including battery (button cell CR2025))

(E) 2 pcs. Stands for satellite speakers

(F) 2 pcs. Wall bracket for satellite speakers

(G) 2 x 3 m Speaker cable for connecting the satellite speakers to the subwoofer

(H) 1 x 2 m Stereo audio cable, RCA jack on both sides

(I) 1 pc. Mains cable

(J) 1 pc. Instruction manual

UNPACKING THE SPEAKER SET

Please unpack the speakers and accessories carefully and check the contents of the box using the list

above. In the event of any transport damage, please contact your supplier. Keep the packing material in

a safe location. The original packaging enables trouble-free transportation for any subsequent relocation

and servicing requirements.

SETTING UP THE SYSTEM COMPONENTS

Satellite speakers (A): The speakers should be positioned to the left and right of the TV. They should be

the same distance from the screen but no more than 1 m. The stands can be used to set up the satellite

speakers on a flat surface (e.g. sideboard, shelves, etc.) or they can be mounted on the wall by using

the wall bracket.“

Subwoofer (B): The subwoofer should be positioned on the floor near the satellite speakers, usually to

the left or right-hand side of the TV. The distance to the screen should not be less than 100 cm for CRT

TVs and 50 cm for flat screen TVs.

Infrared receiver (C): The receiver should be placed near the screen and/or other home cinema

equipment. It can be set up on a flat surface (e.g. sideboard, shelves, etc.) or it can be mounted on the

wall.

Please note: The remote control must be able to communicate freely with the receiver. The receiver

should also be protected from direct sunlight.

Fig. 1 shows you use of the support for the satellites.

Fig. 2 shows the use of the supplied wall mounts for the satellites.

Wall mounting of the IR receiver is illustrated in Fig.3. The mounting screws are not included in delivery.

Important information / safety instructions: The customer is solely responsible for the use of other

wall brackets / speakers attachments. The customer is also solely responsible for the secure attachment

of the speaker bracket to the wall and the selection of suitable mounting material (e.g. screws, wall plugs,

etc.), while taking account of the weight and construction of the speaker and the condition of the wall.

SYSTEM INSTALLATION

The necessary connections for the individual components are illustrated in Fig. 4.

Connecting the satellite speakers to the subwoofer:

The MULTIMEDIA 2100 DIGITAL set comes with prefabricated speaker cables for the two speakers

(2x3m). If possible, use these cables when connecting the speakers. If required, you can shorten and

strip the cables yourself. Please note that both cables for the satellite speakers should be the same

length. If you need longer cables, do not extend the cables supplied, but purchase new, equivalent cables

in the desired length from a specialised store.

The connectors are located at the rear of the satellite speakers. They are equipped with a clamping

mechanism. Press the top of the terminals and insert the stripped ends of the cable into the side holes.

The speaker outputs (1) on the subwoofer are equipped with terminal screws; undo these screws one

after the other and insert the stripped ends of the cable into the side openings. Then re-tighten the ter-

minal screws. Please ensure that any protruding wires do not cause a short circuit. Make sure you pay

attention to the correct polarity.

Connecting the infrared receiver to the subwoofer:

The infrared receiver is equipped with a 5 metre long connecting cable. This cable should not be

shortened or extended. Connect the cable connector to the subwoofer via the IR sensor jack (5).

Connecting a TV to audio input LINE IN 1:

Use the supplied audio cable (H) and connect the audio output on your TV to audio input LINE IN 1 (3).

If your TV has an audio output with fixed level, this is preferable to the audio output with variable level.

Switching off the speakers on your TV: In order to achieve an optimum sound experience the integrated

speakers in your TV must be switched off. In general, this can be done as follows:

1. Via a switch on the back of the TV

2. Via the TV‘s setup menu

3. By using the remote control to set the TV volume to a minimum.

The MULTIMEDIA 2100 DIGITAL set can also be connected to a headphone jack on the TV. A cable

adapter is generally required for this purpose (not included in delivery). The TV‘s speakers are usually

switched off automatically when using the headphone jack. The TV volume should be set to a middle

setting and the overall listening volume should be adjusted via the MULTIMEDIA 2100 DIGITAL remote

control.

Connecting an additional audio source to LINE IN 2:

An additional audio source (e.g. MP3 player, CD player, etc.) can be connected to audio input LINE IN 2

(4) (3.5 mm stereo jack). The necessary connecting cable is not included in delivery.

Connecting an additional audio source to DIGITAL IN:

An additional audio source (e.g. TV, CD player with digital output, etc.) can be connected to digital input

DIGITAL IN (2). The Multimedia 2100 Digital has an optical and koaxial digital input. Please use only one

of them, not both at the same time. The necessary connecting cable is not included in delivery.

Important note:

When connecting audio sources with variable output level (e.g. connection via headphone jack or a TV

set with variable audio output), the level of the audio source should be set in such a way that no distortion

can be heard at the maximum volume setting of the Magnat MULTIMEDIA 2100 DIGITAL. The volume

of the audio source should also be taken into account. No distortions should be evident here either. The

volume of the audio source should also be taken into account. No distortions should be evident here

either.

Mains connection:

Connect the power connector of the subwoofer (9) to an electrical socket via the mains cable (I).

OPERATION

Operating elements on the subwoofer (fig. 4):

Mains switch (7): After installation use this switch to turn on the device. If the device is not going to be

used for a prolonged period, it should be switched off.

STBY/ON button (6): This button can be used to switch between the standby and operating modes. This

function is also possible via the remote control.

Fuse (8): Only use a fuse with the parameters indicated next to the fuse holder, on the rear of the

amplifier.

The infrared receiver (fig. 5):

LED status indication (10): indicates the system‘s possible states:

•LED is illuminated red: The system is in the standby mode.

•LED is illuminated green: The system is switched on and input LINE IN 1 is active.

•LED is illuminated purple: The system is switched on and input LINE IN 2 is active.

•LED is illuminated blue: The system is switched on and input DIGITAL IN is active.

Sensor for the remote control (11): Please aim at this sensor when using the remote control.

Operation with the system remote control (fig. 6):

ON/STBY (12): Switches the device on when it is in the standby mode. If the LED does not illuminate,

actuate the power switch located on the rear of the subwoofer. Conversely the device can be switched

from power operation to the standby mode.

MUTE (13): Switches the sound on and off.

VOLUME (14): Increases (+) or decreases (-) the volume.

SUB (15): Increases (+) / decreases (-) the volume of the subwoofer.

SOURCE (Input selector switch) (16): Switches between the different audio sources (LINE IN 1, LINE

IN 2, DIGITAL IN). The selected input is displayed via the LED on the IR receiver (green, purple or blue).

SERVICE AND TECHNICAL PROBLEMS

If you should encounter any technical problems, please contact your specialist dealer or

Magnat Audio-Produkte GmbH, Tel.: 02234807-0.

SPECIFICATIONS

Satellite speakers

Configuration: Two-way

Power handling capacity RMS / Max.: 50/100 watts

Impedance: 4 – 8 ohm

Frequency range: 90 – 32 000 Hz

Cross-over frequency: 5000 Hz

Efficiency (2.8 V/1 m): 88 dB

Dimensions (WxHxD): 90 x 110 x 110 mm

Weight: 0.9 kg

Subwoofer

Configuration: bass reflex, downfire

Output power RMS/Max.: 120/240 watts

Frequency range: 28 – 200 Hz

Cross-over frequency: 150 Hz

Dimensions (WxHxD): 235 x 400 x 380 mm

Weight: 9 kg

SUBJECT TO TECHNICAL CHANGE

Page is loading ...

Speaker R

Speaker L

e.g. MP3 Player

e.g. CD Player

Subwoofer

Page is loading ...

Wir gratulieren Ihnen! Durch Ihre kluge Wahl sind Sie Besitzer eines MAGNAT HiFi-Produktes geworden. MAGNAT HiFi-Produkte

erfreuen sich aufgrund der hohen Qualität eines ausgezeichneten Rufes weltweit. Dieser hohe Qualitätsstandard ermöglicht es für MAGNAT

HiFi-Lautsprecher 5 Jahre

und für MAGNAT HiFi-Elektronik 2 Jahre Garantie zu gewähren.

Die Produkte werden während des gesamten Fertigungsvorganges laufend kontrolliert und geprüft. Im Servicefall beachten Sie bitte

folgendes:

1. Die Garantiezeit beginnt mit dem Kauf des Produktes und gilt nur für den Erstbesitzer.

2. Während der Garantiezeit beseitigen wir etwaige Mängel, die nachweislich auf Material- oder Fabrikationsfehler beruhen, nach unserer

Wahl durch Austausch oder Nachbesserung der defekten Teile. Weitergehende Ansprüche, insbesondere auf Minderung, Wandlung,

Schadenersatz oder Folgeschäden sind ausgeschlossen. Die Garantiezeit wird von einer Garantieleistung durch uns nicht berührt.

3. Am Produkt dürfen keine unsachgemäßen Eingriffe vorgenommen worden sein.

4. Bei Inanspruchnahme der Garantie wenden Sie sich bitte zunächst an Ihren Fachhändler. Sollte es sich als notwendig erweisen, das

Produktanunseinzuschicken,sosorgenSiebittedafür,dass•dasProduktineinwandfreierOriginalverpackungverschicktwird,•die

Kontrollkarte ausgefüllt dem Produkt beiliegt •dieKaufquittungbeigefügtist.

5.VonderGarantieausgenommensind:•Leuchtmittel•Verschleißteile•Transportschäden,sichtbaroderunsichtbar(Reklamationenfür

solcheSchädenmüssenumgehendbeiderTransportfirma,BahnoderPosteingereichtwerden.)•KratzerinMetallteilen,Frontabdeckungen

u.s.w.(DieseDefektemüsseninnerhalbvon5TagennachKaufdirektbeiIhremHändlerreklamiertwerden.)•Fehler,diedurchfehler-

hafte Aufstellung, falschen Anschluss, unsachgemäße Bedienung (siehe Bedienungsanleitung), Beanspruchung oder äußere gewaltsame

Einwirkungentstandensind.• Unsachgemäßreparierte odergeänderteGeräte,dievonandererSeite alsvon unsgeöffnetwurden.

•FolgeschädenanfremdenGeräten•KostenerstattungbeiSchadensbehebungdurchDritteohneunservorherigesEinverständnis.

Congratulations! You have made a wise selection in becoming the owner of a MAGNAT HiFi equipment. Due to high quality

MAGNAT HiFi products have earned an excellent reputation through the western world. And this high quality standard enables us to grant

a 5-years warranty for MAGNAT HiFi speakers and a 2-years warranty for MAGNAT HiFi-electronic components.

The equipments are checked and tested continously during the entire production process. In case you have problems with your MAGNAT

HiFi equipment, kindly observe the following:

1. The guarantee period commences with the purchase of the component and is applicable only to the original owner.

2. During the guarantee period we will rectify any defects due to faulty material or workmanship by replacing or repairing the defective part

at our discretion. Further claims, and in particular those for price reduction, cancellation of sale, compensation for damages or subsequential

damages, are excluded. The guarantee period is not altered by the fact that we have carried out guarantee work.

3. Unauthorized tampering with the equipment will invalidate this guarantee.

4. Consult your authorized dealer first, if guarantee service is needed. Should it prove necessary to return the component to the factory,

pleaseinsurethat•thecomponentispackedinoriginalfactorypackingingoodcondition•thequalitycontrolcardhasbeenfilledoutand

enclosed with the component •yourencloseyourreceiptasproofofpurchase.

5.Excludedfromtheguaranteeare:•Illuminates•Wearparts•Shippingdamages,eitherreadilyapparentorconcealed(claimsforsuch

damagesmustbelodgedimmediatelywithforwardingagent,therailwayexpressofficeorpostoffice).•Scratchesincases,metalcompo-

nents,frontpanels,etc.(Youmustnotifyyourdealerdirectlyofsuchdefectswithinthreedaysofpurchase.)•Defectscausedbyincorrect

installationorconnection,byoperationerrors(seeoperatinginstructions),byoverloadingorbyexternalforce.•Equipmentswhichhave

beenrepairedincorrectlyormodifiedorwherethecasehasbeenopenedbypersonsotherthanus.•Consoquentialdamagestoother

equipments.•Reimbursementofcools,withoutourpriorconsent,whenrepairingdamagesbythirdparties.

Toutes nos félicitations!

Vouz avez bien choisi et êtes le propriétaire heureux d’un produit MAGNAT. Les produits MAGNAT ont une excellente réputation pour leur

bonne qualité. Pour cette raison, nous accordons 5 ans de garantie sur tous les MAGNAT haut-parleurs et 2 ans de garantie sur tous les

amplificateurs MAGNAT.

Les appareils sont soumis pendant toutes les opérations de fabrications à des contrôles et vérifications constants. Si, pourtant, vous ren-

contrez des difficulés avec votre appareil MAGNAT veuillez tenir compte de ce qui suit:

1. La garantie débute avec l’achat de l’appareil et est valable uniquement pour le premier propriétaire.

2. Pendant la période de garantie nous réparons les dommages provenant des défauts de matériel ou de fabrication et nous procédons, à

notre guise, à l’échange ou à la réparation des pièces défectueuses.

3. Aucune réparation impropre ne doit avoir été effectuée à l’appareil.

4. Lors d’une demande de garantie, veuillez vous adresser en premier lieu à votre distributeur. Si ce dernier décide que l’appareil doit nous

êtreretourné,veuilleztenircompteque:•l’appareilsoitexpédiédanssonermballaged’origine,•lacartedecontrôledûmentrempliesoit

jointe,•lebond’achatsoitjoint.

5.Nesontpascomprisdanslagarantie:•Matérield´eclairage•Piècesd’usure•Avariesdetransport,visiblesounon(detellesréclamations

doiventêtrefaitesimmédiatementauprèsdutransporteur,duchermindeferoudelaposte).•Desrayuressurleboîtier,piècesmétalliques,

couverclesetc.(cesdommagesdoiventêtresignalésdirectementàvotredistributeurdanslestroisjourssuivantl’achat).•Dommages

résultant d’un raccordement incorrect, maniement incorrect (voir instructions de service), surcharge ou application de force extérieure.

•Appareilsréparésnonconformémentoumodifiésetquiontétéouvertsparunepersonneautrequenous.•Dommagesultérieursà

d’autresappareils.•Remboursementdesfraisàdestiersayanteffectuélesréparationssansnotreaccordpréalable.

Garantiekarte

Warranty Card

Typ/Type

Serien-Nr./Serial-No.

Name und Anschrift des Händlers/Stempel

Name and address of the dealer/stamp

Käufer/Customer

Name/Name

Straße/Street

PLZ, Ort/City

Land/Country

Nur gültig in Verbindung mit Ihrer Kaufquittung!

No warranty without receipt!

Kaufdatum/buying date

Page is loading ...

Magnat Audio MULTIMEDIA 2100 DIGITAL Owner's manual

Brand: Magnat Audio

Model: MULTIMEDIA 2100 DIGITAL

Category: Speaker sets

Type: Owner's manual

Download PDF

report

in other languages

italiano: Magnat Audio MULTIMEDIA 2100 DIGITAL Manuale del proprietario
français: Magnat Audio MULTIMEDIA 2100 DIGITAL Le manuel du propriétaire
español: Magnat Audio MULTIMEDIA 2100 DIGITAL El manual del propietario
Deutsch: Magnat Audio MULTIMEDIA 2100 DIGITAL Bedienungsanleitung
русский: Magnat Audio MULTIMEDIA 2100 DIGITAL Инструкция по применению

Magnat Audio MULTIMEDIA 2100 DIGITAL Owner's manual

Magnat Audio MULTIMEDIA 2100 DIGITAL Owner's manual

in other languages

Related papers

Other documents