Newport Brass FE-8700/26 Installation guide

Brand
Newport Brass
Model
FE-8700/26
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

Newport Brass FE-8700/26 is a widespread lavatory faucet that offers durability and style for your bathroom. Constructed of solid brass, this faucet is corrosion-resistant and designed for long-lasting use. The two-handle design allows for precise control of water temperature and volume, while the high-arc spout provides ample clearance for washing hands and filling containers. With its sleek lines and polished chrome finish, the Newport Brass FE-8700/26 is a perfect complement to any bathroom decor.

Newport Brass FE-8700/26 is a widespread lavatory faucet that offers durability and style for your bathroom. Constructed of solid brass, this faucet is corrosion-resistant and designed for long-lasting use. The two-handle design allows for precise control of water temperature and volume, while the high-arc spout provides ample clearance for washing hands and filling containers. With its sleek lines and polished chrome finish, the Newport Brass FE-8700/26 is a perfect complement to any bathroom decor.

INSTALLATION INSTRUCTIONS
WIDESPREAD LAVATORY FAUCET
MODEL No: FE-8700
Congratulations on the purchase of
your Newport product, an excellent
choice, that will give you years of
quality service and enhance the
look and style of your home.
Recommended Installation by a Professional Plumbing Contractor
Note: The use of petroleum base plumbers putty on our products will nullify the warranty. We
recommend the use of clear silicone sealing materials. Recommended deck hole Ø 1-3/8”.
1. Insert SHANK (2) through base WASHER (3) and sink hole. From underside of sink mount the
CRESENTS (4) and mounting NUT(5) onto the SHANK (2). Align the SPOUT (1) and secure into place
by tightening mounting NUT (5). See Figure 1.
2. Place the plastic flange NUT (9), fiber WASHER (10), and SPACER (11) onto valve BODY (8). Insert
valve BODY (8) through sink hole from underside of sink. Thread the MOUNTING NUT (12) onto
the upper position of the valve BODY (8). Valve BODY (8) should extend 1-1/4” above mounting
surface. Secure into place by tightening lower flange NUT (9) to 20 ft. lbs. See Figure 2.
3. Connect coupling NUT (6) to SHANK (2) and HOSE FITTING OUTLET (7) to OUTLET (8A) of each
valve BODY (8). Hand tighten and secure each connection with a wrench ¼ turn. Connect water
supply to INLET (8B) of valve BODIES (8) with one of the three following tyes of risers. See Figure 3:
NOTE: SUPPLY RISERS ARE NOT INCLUDED – SOLD SEPERATELY
A. ½” IPS flexible supply line.
B. 3/8” or ½” O.D. bullnose riser, place friction WASHER (14) and coupling NUT (15) onto bullnose
riser.
C. ½” O.D. copper riser, place coupling NUT (15), friction WASHER (14), and rubber NOSECONE
(13) onto end of copper riser.
4. Use adjustable wrench to tighten connections. Do not over tighten and take care not to kink copper
supply when bending. Use a tube bender and cutter to properly adjust copper supply.
5. With the valve STEM (16) in the closed position, place HANDLE (17) over valve STEM (16). Secure
handle assembly into place by first engaging the valve STEM (16), then position and hold the hande
LEVER (17A) while tightening the set SCREW (18). See Figure 4.
6. Remove drain PLUG (25) from FLANGE (19). Place FLANGE (19) through sink drain opening. Use
plumbing putty to seal between the FLANGE (19) and top side of sink. From bottom side of sink, place
cone shaped rubber WASHER (20) onto FLANGE (19) and slide up against sink bottom.
Note: Cone portion of washer to face upward. Next slide on flat WASHER (21) and loosely secure with
flange NUT (22). Place white WASHER (23) into drain BODY (24) and tighten to FLANGE (19). Positon
the side opening of drain BODY (24) towards the back side of the sink, tighten the flange NUT (22).
7. Place drain PLUG (25) in the orientation as shown in Figure 5, into FLANGE (19). Secure ROD (26) to
drain KNOB (27) and STRAP (28), approximately 1” from end of ROD (26), with SCREW (29). Insert
ball ROD (30) into the side opening of drain BODY (24), secure with ball rod NUT (31). Adjust the rise
of the plunger and CLIP (32) into place. Adjust ball ROD (30) and pop-up ROD (26) so drain will open
and close properly.
8. With handles in the OFF position, turn on water supplies and check all connections for leaks.
9. Operate both handles to flush water lines thoroughly.
NWP-FE-8700
2001 CARNEGIE AVE, SANTA ANA CA 92705 02/01/18
Rev NC (949) 417-5207 EN-3528
WWW.NEWPORTBRASS.COM
Figure 1
1
5
2
4
6
8
12
11
10
9
1-1/4”
Figure 2
16
17
18
6
14
15
13
15
14
17A
3
8B
8A
C
A
B
7
7
NWP-FE-8700
2001 CARNEGIE AVE, SANTA ANA CA 92705 02/01/18
Rev NC (949) 417-5207 EN-3528
WWW.NEWPORTBRASS.COM
Figure 5
20
18
32
21
23
22
24
33
27
26
25
19
NWP-FE-8700
2001 CARNEGIE AVE, SANTA ANA CA 92705 02/01/18
Rev NC (949) 417-5207 EN-3528
WWW.NEWPORTBRASS.COM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Newport Brass FE-8700/26 Installation guide

Brand
Newport Brass
Model
FE-8700/26
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for

Newport Brass FE-8700/26 is a widespread lavatory faucet that offers durability and style for your bathroom. Constructed of solid brass, this faucet is corrosion-resistant and designed for long-lasting use. The two-handle design allows for precise control of water temperature and volume, while the high-arc spout provides ample clearance for washing hands and filling containers. With its sleek lines and polished chrome finish, the Newport Brass FE-8700/26 is a perfect complement to any bathroom decor.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents