AIC Aidos-I User manual

Aidos-I

Server MotherBoard

User's Manual

UM_Aidos-I_v.4_090318

contents

CONTENTS

SAFETY INSTRUCTIONS �� i

About This User Manual �� ii

Chapter 1� Product Features ��1

1�1 General Information ��1

1.2 Specications ��2

Chapter 2� Hardware Setup ��3

2�1 Central Processing Unit (CPU) ��3

2�2 System Memory ��10

Chapter 3� Motherboard Settings ��14

3�1 Motherboard block diagram ��14

3�2 Motherboard Layout ��15

3�3 Motherboard Content List ��15

3�4 Expansion Slots ��16

3�5 Internal Connectors/Jumpers ��17

3�6 LEDs ��26

Chapter 4. BIOS Conguration Settings ��30

4�1 Updating BIOS ��33

Chapter 5. BMC Conguration Settings ��35

5�1 Method 1 (Use the BIOS setup) ��36

5�2 Method 2 (Use a Dos tool - Syscheck) ��41

5�3 BMC web-browser-MegaRAC® GUI Overview ��43

5�3�1 Supported Browsers ��44

5�3�2 Supported OS ��45

5�3�3 Login the web page ��46

5�4 Using MegaRAC SP-X ��49

5�4�1 Dashboard ��51

5�4�2 Field Replaceable Unit(FRU) ��53

5�4�3 Server Health Group ��55

5.4.4 Conguration Group ��63

contents

5�4�5 Remote Control ��135

5�4�6 Auto Video Recording ��153

5�4�7 Maintenance Group ��158

5�4�8 Firmware Update ��167

Chapter 6� Technical Support ��173

This document contains proprietary information about

AIC products and is not to be disclosed or used except in

accordance with applicable agreements.

i

SAFETY INSTRUCTIONS

When installing, operating, or performing maintenance on this equipment, the

following safety precautions should always be observed in order to reduce the

risk of re, electric shock, and personal injury.

Read and understand all instructions.

• Observe warnings and instructions marked on the product.

• For proper mounting instructions, please consult the User’s Manual provided

with this product.

• Do NOT place this product on an unstable cart, stand, table or uneven

surface that might cause the product to fall and sustain serious damage.

• Only install the equipment identified in the User’s Manual. Use of other

equipment could cause improper connection of circuitry and may result in

re or personal injury.

• This product should only be operated with the type of power source

indicated on the marked label. If you are uncertain about which type

of power supply is used in your area, consult your dealer or local Power

Company.

• Disconnect the power supply module before removing power from the

system.

• Unplug this product from the wall outlet before cleaning. Use a damp cloth

for cleaning. Do not use liquid cleaners or aerosol cleaners.

• Do not use this product near a water source, such as a faucet.

• Never spill liquids of any kind on this product.

• Never shove objects of any kind into this product’s open slots, as they may

touch dangerous voltage points or short out parts and could result in re or

electric shock.

• Do not block or cover slots and openings in this unit, as they were made for

ventilation and prevent this unit from overheating. Do not place this product

in a built-in installation unless proper ventilation is available.

• Do not disassemble this product. This product should only be taken apart

by trained personnel. Opening or removing covers and circuit boards may

expose you to electric shock or other risks. Incorrect reassembly can also

cause electric shock when the unit is subsequently used.

• Risk of explosion is possible if battery is replaced with an incompatible type.

Dispose of used batteries accordingly.

• This product is equipped with a three-wire grounding type plug, a plug with

a third (grounding) pin. As a safety feature, this plug is intended to t only

into a grounding type power outlet. If you are unable to insert the plug into

the outlet, contact your electrician to replace the outlet. Do not remove the

grounding type plug or use a 3-Prong To 2-Prong Adapter to circumvent the

safety feature; doing so may result in electric shock and/or damage to this

product.

About This User Manual

ii

This document provides a detailed description of including:

• General Features of the Product

• Hardware Setup

• Motherboard Settings

• BIOS Conguration and Settings

• BMC Conguration and Settings

1

Chapter 1. Product Features

Aidos-I User's Manual

1�1 General Information

Aidos-I, a server grade motherboard supports dual Intel® Haswell – EP

Processor.

Chapter 1� Product Features

2

Aidos-I User's Manual

Chapter 1. Product Features

1.2 Specications

System

Processor

Support

Intel® Xeon® Processors E5-2600 v3 and

next generation Product Family

QPI Speed 9.6 GT/s, 8 GT/s, 7.2 GT/s

Socket Type Socket R3 (FCLGA2011-3)

System

Chipset

Intel® C612 Chipset

System

Memory

A) 4 x memory channels per CPU socket,

2 x DIMMs per channel

B) 16 x DIMM slots support:

- DDR4 2400/2133 RDIMM/LRDIMM

- up to 512GB RDIMM DRx4

- up to 128GB RDIMM SRx4

- up to 1024GB LRDIMM QRx4

- up to 2048GB LRDIMM 3DS 8Rx4

C) Support NVDIMM feature

Expansion

Slots

• 1 x internal PCIe Gen3 x8 slot

• 4 x SFF-8643 connectors,

each supports PCIe Gen3

System BIOS

BIOS Type Insyde BIOS code @ 16MB Flash EEPROM

BIOS

Features

• ACPI1.0/2.0/3.0

• PXE 2.0

• WOL

• AC loss recovery

• IPMI KCS interface

• SMBIOS 2.0

• Serial console redirection

• BIOS Boot Specication

• BIOS Recovery Mode

• SRIOV

On-board

Devices

SATA

Built-in SATA controller with RAID support on

Intel® C612 Chipset

IPMI

Aspeed AST2400 Advanced PCIe Graphics &

Remote Management Processor

• Baseboard Management Controller

• Intelligent Platform Interface 2.0 (IPMI 2.0)

• iKVM, Media Redirection, IPMI over LAN,

Serial over LAN

• SMASH Support

Network

Controller

• Intel 82599ES 10 Gigabit Ethernet Controller,

SFP+, dual port 10 GbE, PCIe v2.0 (5.0GT/s)

• Intel Ethernet Controler I350 AM2 supports

dual GbE ports, PCIe v2.0 (5.0GT/s)

• Realtek RTL8201EL single port 10/100Mbps

Ethernet PHYceiver for dedicated BMC

management port

Graphics

Aspeed AST2400 Advanced PCIe Graphics &

Remote Management Processor

• PCIe VGA/2D Controller

• 1920x1200@60Hz 32bpp

Input/Output

Serial ATA

• 8 x SATA 6.0Gb/s (by 2 x mini-SAS connector)

• 2 x SATA 6.0Gb/s (by 2 x SATA connector)

LAN

• 2 x external SFP+ connectors support 10 GbE

• 2 x external RJ45 ports support 1 GbE

• 1 x internal PHY header dedicate for BMC

management

USB

• 2 x USB 3.0 double-stack Type-A connectors

• 1 x USB internal pin-header to support

2 x USB 3.0 + 2 x USB 2.0

VGA

• 1 x external VGA port

• 1 x internal VGA pin-header

(share with external VGA port)

Serial Port 2 x internal COM pin-headers

Others

Debug display pin-header, GPIO port

IPMB pin-header

Additional

Information

• 1 x power button

• 1 x reset button

• 1 x ID button

• 1 x system failure LED

3

Chapter 2. Hardware Setup

Aidos-I User's Manual

Chapter 2� Hardware Setup

2�1 Central Processing Unit (CPU)

2.1.1 Removing the Processor Heatsink

The heatsink is attached to the server board or processor socket with

captive fasteners. Using a #2 Phillips* screwdriver, loosen the four screws

located on the heatsink corners in a diagonal manner using the following

procedure:

• Using a #2 Phillips* screwdriver, start with screw 1 and loosen it by

giving it two rotations and stop (see letter A).

• Proceed to screw 2 and loosen it by giving it two rotations and stop

(see letter B). Similarly, loosen screws 3 and 4. Repeat steps A and

B by giving each screw two rotations each time until all screws are

loosened.

• Lift the heatsink straight up (see letter C).

R

EM

OVE

REMOVE

LGA20

11-3

** SUPPLIER IDENTI

FI

C

A

TION HERE **

INSTALL PROCESSOR B

EFOR

E

REMOVING COVER

SAVE AN

D

REPLACE

COVER

IF P

ROCESSOR IS REMOVE

D

Processor

Socket

2

3

1

4

A

B

C

IMPORTANT :

Do not fully loosen.

Chapter 2. Hardware Setup

4

Aidos-I User's Manual

2.1.2 Installing the Processor

2.1.2.1 Unlatch the CPU Load Plate

• Push the lever handle labeled “OPEN 1st” (see letter A) down and

toward the CPU socket. Rotate the lever handle up.

• Repeat the steps for the second lever handle (see letter B).

CAUTION :

Processor must be appropriate: You may damage the server board if

you install a processor that is inappropriate for your server.

CAUTION :

ESD and handling processors: Reduce the risk of electrostatic

discharge (ESD) damage to the processor by doing the following:

(1) Touch the metal chassis before touching the processor or

server board. Keep part of your body in contact with the metal

chassis to dissipate the static charge while handling the processor.

(2) Avoid moving around unnecessarily.

REMOVE

LGA2011-3

** SUPPLIER IDENTIFIC

ATION HERE **

INSTALL PROCESSOR BEFORE

REMOVING COVER

SAVE AND REPLACE COVER

IF PROCESSOR IS REMOVED

A

REMOVE

LGA2011-3

** SUPPLIER IDENTIFIC

ATION HERE **

INSTALL PROCESSOR BEFORE

REMOVING COVER

SAVE AND REPLACE COVER

IF PROCESSOR IS REMOVED

B

5

Chapter 2. Hardware Setup

Aidos-I User's Manual

2.1.2.2 Lift open the Load Plate

• Rotate the right lever handle down until it releases the Load Plate

(see letter A).

• While holding down the lever handle, with your other hand, lift open

the Load Plate (see letter B).

B

REMOVE

LGA2011-3

** SUPPLIER IDENTIFIC

ATION HERE **

INSTALL PROCESSOR BEFORE

REMOVING COVER

SAVE AND REPLACE COVER

IF PROCESSOR IS REMOVED

A

Chapter 2. Hardware Setup

6

Aidos-I User's Manual

2.1.2.3 Install the Processor

• Remove the processor from its package.

• Carefully remove the protective cover from the bottom side of the

CPU, taking care not to touch any CPU contacts (see letter A).

• Orient the processor with the socket so that the processor cutouts

match the four orientation posts on the socket (see letter B). Note the

location of a gold key at the corner of the processor (see letter C).

Carefully place (Do NOT drop) the CPU into the socket.

CAUTION :

The pins inside the CPU socket are extremely sensitive. Other than

the CPU, no object should make contact with the pins inside the

CPU socket. A damaged CPU socket pin may render the socket inoperable,

and will produce erroneous CPU or other system errors if used.

NOTE :

The underside of the processor has components that may damage the

socket pins if installed improperly. The processor must align correctly

with the socket opening before installation. DO NOT DROP the

processor into the socket.

NOTE :

When possible, a CPU insertion tool should be used when installing the

CPU.

A

B

C

7

Chapter 2. Hardware Setup

Aidos-I User's Manual

2.1.2.4 Remove the Socket Cover. Remove the socket cover from the

load plate by pressing it out.

2.1.2.5 Close the Load Plate. Carefully lower the load plate down over

the processor.

2.1.2.6 Lock down the Load Plate

• Push down on the locking lever on the CLOSE 1st side (see letter A).

Slide the tip of the lever under the notch in the load plate (see letter B).

Make sure the load plate tab engages under the socket lever when

fully closed.

• b.Repeat the steps to latch the locking lever on the other side (see

letter C). Latch the levers in the order as shown.

NOTE :

The socket cover should be saved and re-used should the processor

need to be removed at anytime in the future.

Save the

protective

cover.

A

B

C

Chapter 2. Hardware Setup

8

Aidos-I User's Manual

2.1.3 Installing the Processor Heatsink

• If present, remove the protective lm covering the Thermal Interface

Material on the bottom side of the heatsink (see letter A).

• Align the heatsink ns to the front and back of the chassis for correct

airow. The airow goes from front-to-back of the chassis (see letter B).

• Each heatsink has four captive fasteners and should be tightened in a

diagonal manner using the following procedure:

• Using a #2 Phillips* screwdriver, start with screw 1 and engage screw

threads by giving it two rotations and stop (see letter C). (Do not fully

tighten.)

• Proceed to screw 2 and engage screw threads by giving it two

rotations and stop (see letter D). Similarly, engage screws 3 and 4.

• Repeat steps C and D by giving each screw two rotations each time

until each screw is lightly tightened up to a maximum of 8 inch-lbs

torque (see letter E).

NOTE :

The processor heatsink for CPU1 and CPU2 is different. FXXCA91X91HS is

for CPU1, while FXXEA91X91HS2 is for CPU2. Mislocating the heatsink

will cause serious thermal damage.

C

Processor

Socket

AIRFLOW

Chassis Front

2

3

1

4

A

B

TIM

D

CAUTION:

Do not over-tighten fasteners.

E

9

Chapter 2. Hardware Setup

Aidos-I User's Manual

2.1.4 Removing the Processor

NOTE :

Remove the processor by carefully lifting it out of the socket, taking care

NOT to drop the processor and not touching any pins inside the socket.

Install the socket cover if a replacement processor is not going to be installed.

Chapter 2. Hardware Setup

10

Aidos-I User's Manual

2�2 System Memory

This server board supports up to sixteen DDR4 1333/1600/1866/2133

Registered ECC SDRAM(RDIMM) / Load-Reduced DIMM (LRDIMM).

JCPU1

JCPU0

SATA0~3

SATA4

SATA5

SATA0~3

Reset Button

CPU0_DIMMH1

CPU0_DIMMG1

CPU0_DIMMH0

CPU0_DIMMG0

CPU0_DIMMB1

CPU0_DIMMB0

CPU0_DIMMA1

CPU0_DIMMA0

CPU0_DIMMC0 CPU0_DIMME0

CPU0_DIMMF0

CPU0_DIMME1

CPU0_DIMMF1

CPU0_DIMMC1

CPU0_DIMMD0

CPU0_DIMMD1

11

Chapter 2. Hardware Setup

Aidos-I User's Manual

1. Populate DIMMs in the following order:

JDIMMB1

JDIMMH1

JDIMMG1

JDIMMG0

JDIMMH0JDIMMB0

JDIMMA1

JDIMMA0

JDIMMC0

JDIMMC1

JDIMMD0

JDIMMD1

JDIMME0

JDIMME1

JDIMMF0

JDIMMF1

CPU0

CPU1

JDIMMB1

JDIMMH1

JDIMMG1

JDIMMG0

JDIMMH0JDIMMB0

JDIMMA1

JDIMMA0

JDIMMC0

JDIMMC1

JDIMMD0

JDIMMD1

JDIMME0

JDIMME1

JDIMMF0

JDIMMF1

CPU0

CPU1

DIMM Numbers DIMM ARRANGMENT

2 DIMMs

CPU0 CPU1

JDIMM_C0 JDIMM_E0

JDIMMB1

JDIMMH1

JDIMMG1

JDIMMG0

JDIMMH0JDIMMB0

JDIMMA1

JDIMMA0

JDIMMC0

JDIMMC1

JDIMMD0

JDIMMD1

JDIMME0

JDIMME1

JDIMMF0

JDIMMF1

CPU0

CPU1

4 DIMMs

CPU0 CPU1

JDIMM_C0 JDIMM_E0

JDIMM_D0 JDIMM_F0

6 DIMMs

CPU0 CPU1

JDIMM_C0 JDIMM_E0

JDIMM_D0 JDIMM_F0

JDIMM_A0 JDIMM_G0

JDIMMB1

JDIMMH1

JDIMMG1

JDIMMG0

JDIMMH0JDIMMB0

JDIMMA1

JDIMMA0

JDIMMC0

JDIMMC1

JDIMMD0

JDIMMD1

JDIMME0

JDIMME1

JDIMMF0

JDIMMF1

CPU0

CPU1

8 DIMMs

CPU0 CPU1

JDIMM_C0 JDIMM_E0

JDIMM_D0 JDIMM_F0

JDIMM_B0 JDIMM_H0

JDIMM_A0 JDIMM_G0

Chapter 2. Hardware Setup

12

Aidos-I User's Manual

13

Chapter 2. Hardware Setup

Aidos-I User's Manual

2. Unlock a DIMM socket by pressing the retaining clips outward.

3. Insert module vertically and press down until it snaps into place.

DIMM notch

Note: DIMM notch and socket bump must align as shown.

Chapter 3. Motherboard Settings

14

Aidos-I User's Manual

Chapter 3� Motherboard Settings

This section describes the jumpers, internal connectors, and LEDs setting on

Aidos motherboard. Motherboard layout and important jumper settings

are listed as below.

3�1 Motherboard block diagram

Page is loading ...

AIC Aidos-I User manual

Related papers

Other documents