Vivo STAND-V002U Assembly Instructions

Brand: Vivo

Model: STAND-V002U

Category: Flat panel desk mounts

Type: Assembly Instructions

Dual Monitor Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v002u

SKU: STAND-V002U

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

WARNING!

A (x1)

Column

B (x1)

Base

C (x1)

Clamp

M-A (x8)

M4x12

M-B (x8)

M5x12

O (x1)

6mm Allen

Wrench

K (x3)

Flat Head Bolt

L (x1)

Support

Plate

M (x1)

Grommet Bolt

N (x1)

4mm Allen

Wrench

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

D (x1)

Clamp

Plate

E (x1)

Grommet

Plate

G (x2)

VESA Plate

H (x1)

Cable Clip

I (x1)

Pad

J (x2)

Short Bolt

M-C (x8)

D5 Washer

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

NOTE: SOME HARDWARE MAY NOT BE USED

F (x1)

Arm

ASSEMBLY STEPS

STEP 1

15.4lbs

(7kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

STEP 2

Mount column (A) to base (B) using short bolts (J). Tighten with 6mm Allen wrench (O).

OPTION A: Grommet Installation

Mount grommet plate (E) to base using

flat head bolts (K) and tighten with 4mm

Allen wrench (N). Cut rear portion o

from pad (I), peel backing, and stick to

installed grommet plate. Place the base

over grommet hole in desk, and secure

using grommet bolt (M) and support

plate (L). Tighten with 6mm Allen wrench

(O). Please note, desktop thickness must

be 3/8” - 1” (10mm - 25mm).

PER SCREEN

TOOLS NEEDED

Phillips

Screwdriver

STEP 2 (Continued)

OPTION B: Clamp Installation

Mount clamp plate (D) to base using flat head bolts (K) and tighten with 4mm Allen wrench (N). Peel

backing from pad (I) and stick to installed clamp plate. For 5/8” - 1” (15 - 25mm) desktop thickness:

Place the base near the back edge of the desk. Position clamp (C) on base and desktop, then tighten

clamp screws with 4mm Allen wrench (N). Install cable clip (H) to column. For 3/8” - 3/4” (10 - 20mm)

desktop thickness: Remove plastic foot from clamp (C) and reinstall upside down. Place the base near

the back edge of the desk. Position clamp on base and desktop, then tighten clamp bolts with 4mm

Allen wrench (N). Install cable clip (H) to column.

STEP 3

Mount VESA plate (G) to back of monitor using screws (M-A or M-B) and washers

(M-C), making sure the slot in back is facing down.

STEP 4

Slide arm (F) onto column (A). Tighten knob and use 4mm Allen wrench (N) to secure

arm at desired height.

M- A

M- B

M- C

STEP 5

STEP 6

Slide monitors with VESA plates onto mounting brackets on arm. Tighten the screw

on the side of each bracket to secure the monitors.

Loosen the knob to adjust monitor height. Manage cables and store

tools using installed cable clip.

Adjust as Desired

LAST UPDATED: 05/13/2020

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected]

AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Vivo STAND-V002U Assembly Instructions

Brand: Vivo

Model: STAND-V002U

Category: Flat panel desk mounts

Type: Assembly Instructions

Download PDF

report

Vivo STAND-V002U Assembly Instructions

Vivo STAND-V002U Assembly Instructions

Related papers

Other documents