Vivo STAND-V002U Assembly Instructions

Vivo
Brand
Vivo
Model
STAND-V002U
Category
Flat panel desk mounts
Type
Assembly Instructions
Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002u
SKU: STAND-V002U
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
WARNING!
A (x1)
Column
B (x1)
Base
C (x1)
Clamp
M-A (x8)
M4x12
M-B (x8)
M5x12
O (x1)
6mm Allen
Wrench
K (x3)
Flat Head Bolt
L (x1)
Support
Plate
M (x1)
Grommet Bolt
N (x1)
4mm Allen
Wrench
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
D (x1)
Clamp
Plate
E (x1)
Grommet
Plate
G (x2)
VESA Plate
H (x1)
Cable Clip
I (x1)
Pad
J (x2)
Short Bolt
M-C (x8)
D5 Washer
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
F (x1)
Arm
3
ASSEMBLY STEPS
STEP 1
15.4lbs
(7kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
STEP 2
Mount column (A) to base (B) using short bolts (J). Tighten with 6mm Allen wrench (O).
OPTION A: Grommet Installation
Mount grommet plate (E) to base using
flat head bolts (K) and tighten with 4mm
Allen wrench (N). Cut rear portion o
from pad (I), peel backing, and stick to
installed grommet plate. Place the base
over grommet hole in desk, and secure
using grommet bolt (M) and support
plate (L). Tighten with 6mm Allen wrench
(O). Please note, desktop thickness must
be 3/8” - 1” (10mm - 25mm).
A
B
J
O
4
E
I
3
I
2
N
K
1
PER SCREEN
TOOLS NEEDED
Phillips
Screwdriver
4
STEP 2 (Continued)
OPTION B: Clamp Installation
Mount clamp plate (D) to base using flat head bolts (K) and tighten with 4mm Allen wrench (N). Peel
backing from pad (I) and stick to installed clamp plate. For 5/8” - 1” (15 - 25mm) desktop thickness:
Place the base near the back edge of the desk. Position clamp (C) on base and desktop, then tighten
clamp screws with 4mm Allen wrench (N). Install cable clip (H) to column. For 3/8” - 3/4” (10 - 20mm)
desktop thickness: Remove plastic foot from clamp (C) and reinstall upside down. Place the base near
the back edge of the desk. Position clamp on base and desktop, then tighten clamp bolts with 4mm
Allen wrench (N). Install cable clip (H) to column.
D
I
3
2
N
K
1
5
STEP 3
Mount VESA plate (G) to back of monitor using screws (M-A or M-B) and washers
(M-C), making sure the slot in back is facing down.
STEP 4
Slide arm (F) onto column (A). Tighten knob and use 4mm Allen wrench (N) to secure
arm at desired height.
TV
TV
TV
G
M- A
M- B
M- C
N
F
6
STEP 5
STEP 6
Slide monitors with VESA plates onto mounting brackets on arm. Tighten the screw
on the side of each bracket to secure the monitors.
1
N
2
N
O
Loosen the knob to adjust monitor height. Manage cables and store
tools using installed cable clip.
7
Adjust as Desired
LAST UPDATED: 05/13/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected]
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Vivo STAND-V002U Assembly Instructions

Vivo
Brand
Vivo
Model
STAND-V002U
Category
Flat panel desk mounts
Type
Assembly Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents