Unbranded PSH4BE Product information

Unbranded
Brand
Unbranded
Model
PSH4BE
Type
Product information

Unbranded PSH4BE is a versatile and efficient submersible pump designed for various water transfer applications. With its powerful motor and durable construction, it can handle clean or slightly dirty water, making it suitable for tasks such as draining flooded areas, emptying pools, irrigating gardens, or transferring water between containers. The pump features an adjustable float switch that allows for automatic operation and prevents dry running, ensuring its longevity.

Unbranded PSH4BE is a versatile and efficient submersible pump designed for various water transfer applications. With its powerful motor and durable construction, it can handle clean or slightly dirty water, making it suitable for tasks such as draining flooded areas, emptying pools, irrigating gardens, or transferring water between containers. The pump features an adjustable float switch that allows for automatic operation and prevents dry running, ensuring its longevity.

CY0
W2
R
E
T1
T2
C
Y
0
0
W2
R
DFT
E
DF1
DF2
Defrost Control Board
RT
LEFT
T1
T2
L2
L1
Single Phase
Field Supply
Grounding
Lug
High Press.
Switch
Low Press.
Switch
Compressor
Start Capacitor
Defrost
Thermostat
Reversing Valve
Solenoid
Comfort
Alert
H
C
T1
T2
T3
CCH
ECM
ECM WIRING NOTES:
1) FOR 825 RPM ATTACH WHITE TO RIGHT CONTACTOR. (FOR SKUS 919660,919661,919662,919664)
2) FOR 960 RPM ATTACH YELLOW TO RIGHT CONTACTOR. (FOR SKU 919663)
3) FOR 1100 RPM ATTACH WHITE AND YELLOW TO RIGHT
CONTACTOR.
Y
L
R
C
Start
Relay
1
5
2
YELLOW
YELLOW
YELLOW/BLACK
YELLOW/BLACK
BLACK
BLACK
YELLOW
RED
RED
RED
BLACK
BLACK
RED
BLACK
BROWN
BLACK
WHITE
YELLOW
SEE ECM WIRING NOTES
BLACK
BLACK
YELLOW
RED
BLUE
BLUE
BLACK
Split System Heat Pump (Outdoor Section) Single Phase
WIRING DIAGRAM
NOTES:
1. Disconnect all power before servicing.
2. For supply connections use copper conductors only.
3. Not suitable on systems that exceed 150 volts to ground.
4. For replacement wires use conductors suitable for 105˚C.
5. For ampacities and overcurrent protection, see unit rating plate.
6. Connect to 24 vac/40va/class 2 circuit. See furnace/air handler
installation instructions for control circuit and optional
relay/transformer kits.
Defrost Board Operation:
1. Closing during defrost. Rating: 1 Amp.Max
2. Opens during defrost. Rating: 2HP at 230 Vac Max.
3. Closed when “Y” is on. Open when “Y” is off.
Provides “off” delay time of 5 min. when “Y” opens.
4. With DFT closed and “Y” closed, compressor run
time is accumulated. Opening of DFT during
defrost or interval period resets the interval to 0.
CC - Contactor Coil
CCH - Crankcase Heater
DFT - Defrost Thermostat
HPS - High Pressure Switch
REVS - Reversing Valve Solenoid
* - Hard Start Kit Field Installed
1. Couper le courant avant de faire letretien.
2. Employez uniquement des conducteurs en cuivre.
3. Ne convient pas aux installations de plus de 150 volt a la terre.
FIELD WIRING
LEGEND:
LOW VOLTAGE
HIGH VOLTAGE
Low Voltage
Terminals
E
Defrost Control Board
DFT
Control
Logic
DF1
DF2
DFT
1
2
3
4
1
R
W2
O
Y
C
T2
T1
R
W2
O
Y
C
RVS
HPS
LPS
Y
CRL
Comfort
Alert
CC
Select
Models Only
L
Status LED Status LED Description
Green "POWER"
Module has power
Red "TRIP"
Thermostat demand signal Y is present,
but the compressor is not running
Yellow "ALERT" Flash Code 1
Long Run Time
Compressor is running extremely long
run cycle
Yellow "ALERT" Flash Code 2
System Pressure Trip
Discharge or suction pressure out of
limits or compressor overloaded
Yellow "ALERT" Flash Code 3
Short Cycling
Compressor is running only briefly
Yellow "ALERT" Flash Code 4 Locked Rotor
Yellow "ALERT" Flash Code 5 Open Circuit
Yellow "ALERT" Flash Code 6
Open Start Circuit
Current only in run circuit
Yellow "ALERT" Flash Code 7
Open Run Circuit
Current only in start circuit
Yellow "ALERT" Flash Code 8
Welded Contactor
Compressor always runs
Yellow "ALERT" Flash Code 9
Low Voltage
Control circuit < 17 VAC
Compressor
R
C
S
HC
CCH
L1
T1
L2
T2
Compressor
Contacts
ECM
208/230V
Instructions for control circuit and optional relay/transformer kit.
710660A (Replaces 7106600)
¢710660{¤
  • Page 1 1

Unbranded PSH4BE Product information

Unbranded
Brand
Unbranded
Model
PSH4BE
Type
Product information

Unbranded PSH4BE is a versatile and efficient submersible pump designed for various water transfer applications. With its powerful motor and durable construction, it can handle clean or slightly dirty water, making it suitable for tasks such as draining flooded areas, emptying pools, irrigating gardens, or transferring water between containers. The pump features an adjustable float switch that allows for automatic operation and prevents dry running, ensuring its longevity.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents