© 2016 Anviz Global Inc.
IP CAMERA SERIES
OPERATION GUIDE
V1.0
I
About this Document
This manual is intended for administrators and users of the Anviz Network Cameras. It includes
instructions for using and managing the product on your network. Previous experience of
networking will be of use when using this product. Some knowledge of UNIX or Linux-based
systems may also be beneficial, for developing shell scripts and applications. Later versions of this
document will be posted to the Anviz website, as required. See also the product’s online help,
available via the web-based interface.
Legal Considerations
Video surveillance can be regulated by laws that vary from country to country. Check the laws in
your local region before using this product for surveillance purposes. This product includes one (1)
H.264 decoder license. To purchase further licenses, contact your reseller.
Liability
Every care has been taken in the preparation of this document. Please inform your local Anviz
office of any inaccuracies or omissions. Anviz Communications cannot be held responsible for any
technical or typographical errors and reserves the right to make changes to the product and
manuals without prior notice. Anviz Communications makes no warranty of any kind with regard
to the material contained within this document, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose. Anviz Communications shall not
be liable nor responsible for incidental or consequential damages in connection with the
furnishing, performance or use of this material. This product is only to be used for its intended
purpose.
Intellectual Property Rights
Anviz has intellectual property rights relating to technology embodied in the product described in
this document. In particular, and without limitation, these intellectual property rights may include
one or more of the patents listed at http://www.anviz.com/en-us and one or more additional
patents or pending patent applications in the US and other countries.
This product contains licensed third-party software. See the menu item ―About‖ in the product’s
user interface for more information.
Equipment Modifications
This equipment must be installed and used in strict accordance with the instructions given in the
user documentation. This equipment contains no user-serviceable components. Unauthorized
equipment changes or modifications will invalidate all applicable regulatory certifications and
approvals.
II
Trademark Acknowledgments
Anviz is registered trademarks or trademark applications of Anviz in various jurisdictions. All other
company names and products are trademarks or registered trademarks of their respective
companies.
Apple, Boa, Apache, Bonjour, Ethernet, Internet Explorer, Linux, Microsoft, Mozilla, Real, SMPTE,
QuickTime, UNIX, Windows, Windows Vista and WWW are registered trademarks of the respective
holders.
Java and all Java-based trademarks and logos are trademarks or registered trademarks of Oracle
and/or its affiliates. UPnPTM is a certification mark of the UPnPTM Implementers Corporation.
WPA, WPA2 and Wi-Fi Protected Setup are marks of the Wi-Fi Alliance.
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to the equipment that are not expressly approved by the
responsible party for compliance could void the user’s authority to operate the equipment.
European Community Compliance Statement
This product has been tested and found to comply with the limits for Class B
Information Technology Equipment according to European Standard EN 55022 and
EN 55024. In a domestic environment, this product may cause radio interference in
which cause the user may be required to take adequate measures.
IMPORTANT
The use of surveillance devices may be prohibited by law in your country. The Network Camera is
III
not only a high-performance web-ready camera but can also be part of a flexible surveillance
system. It is the user’s responsibility to ensure that the operation of such devices is legal before
installing this unit for its intended use.
IMPORTANT
It is important to first verify that all contents received are complete according to the Package
Contents listed below. Take note of the warnings in the Quick Installation Guide before the
Network Camera is installed; then carefully read and follow the instructions in the Installation
chapter to avoid damage due to faulty assembly and installation. This also ensures the product is
used properly as intended.
Safety Precautions
All the following safety and operational instructions to prevent harm or injury to the operator(s) or
other persons should be read carefully before the unit is activated.
WARNING
To prevent fire or shock hazard, avoid exposing this unit to rain or moisture.
Do not block ventilation openings.
Do not place anything on top of the unit that might spill or fall into it.
Do not attempt to service this unit yourself, as opening or removing covers may expose you
to dangerous voltage or other hazards. Please refer all servicing to your distributor/ retailer.
Do not use liquid cleaners or aerosols for cleaning.
To prevent fire or electric shock, do not overload wall outlets or extension cords
PoE warning : If the PoE injector is used instead of the supplied power adaptor, all of the
wiring to and from the injector must be routed/ installed inside a building/ plant and never
routed/ installed outside of the building/ plant.
CAUTION
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to
the instructions.
IV
How to Use This Operation Guide ............................................................................. 1
System Requirements .................................................................................................. 2
1 Accessing the Network Camera ............................................................................ 3
1.2 Network Deployment ............................................................................................................... 3
1.3 Web Server Access .................................................................................................................... 8
2 Setting ................................................................................................................... 10
2.1 Main Page................................................................................................................................... 10
2.2 Image Setting ............................................................................................................................ 12
2.3 Setting .......................................................................................................................................... 20
3 Q&A ....................................................................................................................... 58
3.1 How do I set up the motion detection area and its sensitivity .............................. 58
3.2 How do I add or modify the users and their authority ............................................. 58
4 Glossary................................................................................................................. 59
CONTENTS
1 / 60
This Guide explains how to operate the Network Camera from a computer. The User’s Guide is
designed to be read on the computer display. This section gives tips on making the most of the
User’s Guide-read it before you operate the camera.
Jumping to a related page
When you read the Operation Guide on the computer display, you can click on a sentence to jump
to a related page.
Software display examples
Note that the displays shown in the Operation Guide are explanatory examples. Some displays
may be different from the ones that appear in actual use.
Printing the Operation Guide
Depending on your system, certain displays or illustrations in the Operation Guide, when printed
out, may differ from those that appear on your screen.
Installation Guide (printed matter)
The supplied Installation Guide describes the names and functions of parts and controls of the
Network Camera, connection examples, and how to set up the camera. Be sure to read the
Installation Guide before hand.
How to Use This Operation Guide
2 / 60
The following computer environment is necessary for the computer to display images and the
controls of the camera.
OS
Microsoft Windows XP, Windows Vista (32bit version only), Windows 7 (32-bit version only)
Authorized editions:
Windows XP: Professional
Windows Vista: Ultimate, Business
Windows 7: Ultimate, Professional
Microsoft DirectX 9.0c or higher
Web Browser
Microsoft Internet Explorer Ver. 8.0, Ver. 9.0, Ver. 10.0
CPU
Intel Core 2 Duo, 2 GHz or higher
Memory
2 GB or more
Display
1600 × 1200 pixels or higher
(2560 × 1600 pixels or higher is recommended)
System Requirements
3 / 60
This chapter explains how to access the Network Camera through web browsers.
1.2 Network Deployment
1.2.1 Setting up the Network Camera over the Internet
This section explains how to configure the Network Camera to an Internet Network.
Internet connection with static IP
Choose this connection type if you are required to use a static IP for the Network
Camera.
Internet connection via a router
Before setting up the Network Camera over the Internet, make sure you have a router
and follow the steps below.
1. Connect your Network Camera to a router.
2. Assign a LAN IP address, the subnet mask and the gateway. Please refer to
Software Installation on chapter Network Setting(DM) for details.
Default configuration of IPC:
IP address: 192.168.100.100
User name: admin
Password: admin
3. Save the static IP in the router.
4. Set port mapping, E.g., 80, 8000, 8200 and 554 ports. The steps for port mapping
vary depending on different routers. Please call the router manufacturer for
assistance with port mapping.
5. Visit the network camera through a web browser or the client software over the
internet.
1 Accessing the Network Camera
4 / 60
1.2.2 Enable DHCP Function
This function can only work if the LAN, which the unit is connected to, has a Router /
DHCP server. If the Router / DHCP server is working in the LAN, please plug the net
cable into the router / switch and the other end of the connector in the camera. Set the
Network setting and turn on the DHCP setting to use the DHCP protocol. The IP
Camera will obtain an IP address automatically from the Router / DHCP server.
Note: The IP Camera default setting is DHCP OFF. Users can obtain an IP address
automatically from the DHCP server.
1.2.3 Network Setting (DM)
Installation IntelliSight DM, free-bundled software included on the product CD, helps
you set up your Network Camera on the LAN.
1.2.3.1 DM Installation
Install the DM from the supported CD-R:
1. Exit all applications currently running in the selected PC.
2. Insert the supported CD in the CD-ROM drive. The program will execute the
installation automatically. Follow the on-screen instructions to proceed with the
rest of the installation procedure as they appear.
3. After the installation is complete, pop up the START menu from your computer,
and point to Programs DM to open up the program selection page as shown. Click
on the DM tag to start the DM program.
Install the DM from the ZIP file:
1. Save the ZIP file to your PC and extract the file to a designated directory.
2. Open the extracted folder. The folder contains 1 file.
3. Click the setup icon to execute the installation and then follow the on-screen
instructions to proceed with the rest of the installation procedure.
4. After the installation is complete, click the START menu from your computer, and
point to Programs DM to start the DM program.
Note: Please make sure the TCP/IP communication software has been properly set and
configured in your computer.
The program will list all Anviz network devices on the same LAN
5 / 60
1.2.3.2 DM Operation
Search:
Search the cameras in the same LAN; Include the following information of the camera:
IP address, Mac address, Version, Hardware, Model, Sensor, SN, Vendor;
Network:
Check or modify the network information (IP address, Netmask, Gateway) of the
appointed camera; Click ―Apply‖ to apply the operation, or click ―Cancel‖ to cancel the
operation. Then click ―OK‖ to exit this window.
1.2.3.3 IP Setting
Make sure that you have been added the IP address which in the same network
segment with the camera network before access the camera.
6 / 60
Kindly follow the below steps to do the setting.
Click Start > Control Panel > Network and Internet 1.
Click Change adapter settings > Local Area > Properties 2.
Double click the Internet Protocol Version 4 (TCP/IP4) to open the properties 3.
setting page.
Click the Advanced setting to open the adding page. 4.
7 / 60
Click the Add to add another network, which is within the same network with 5.
camera.
Click the Add to finish this setting. Then click ok to enable this changing. 6.
Click on the MAC and model name which matches the product label on your 7.
device to connect to the Network Camera via Internet Explorer.
8 / 60
1.3 Web Server Access
Use Installation DM to access to the Network Cameras. If you do not want to use the
DM, kindly follow these steps to access the Network Camera.
Start up the Microsoft Internet Explorer, and then follow the steps below to 1.
connect the IP camera.
Click on the URL block at the top of the window. 2.
Enter the URL address of the IP camera into the URL block and press the ―Enter‖ 3.
button to enter the home page.
Enter the "User Name" and "Password" in the appropriate spaces. 4.
Click on the ―OK‖ button to set your entries, and automatically exit the page. 5.
If it is the first time installing the Anviz network camera, an information bar will 6.
pop up as shown below. Follow the instructions to install the required plug-in on
your computer.
Note:
1. The default "User Name" and "Password" are ―admin‖ and ―admin‖, respectively.
2. The page headlined "Enter Network Password‖ is shown below. Please enter the
user name and password of the IP camera when you see it. If either the user name
or the password is incorrect, please check the input data and rectify it as necessary.
3. Once authorized successfully, the login page will not appear again until you close
the window and reconnect it.
4. The initial sequence of proceeding is to type in your IP address and click the "Enter"
button to access the home page. If and when you reviseor change data in the
"SYSTEM USERS" page, the sequence will alter to initially show the "Enter Network
Password" page.
9 / 60
ActiveX Control Installing
Open the IE Browser, input the camera’s IP in the address, and input username and
password to login. There would be one prompt to require you to install our ―Anviz
Cameras’ ActiveX‖ for the first time login.
You will see the below reminder:
Click the ―Install‖ button to install this plug-in.
After processing auto-finished, the homepage of webserver would display normally.
10 / 60
2 Setting
This chapter explains the layout of the main page, and how to configure the camera and saving
options on the local computer. When completed with the settings on this page, click Save on the
page bottom to enable the settings.
2.1 Main Page
The Live Video from the IP camera is displayed on the home page when your PC is online
with the IP camera. There are also additional settings provided on the home page.
Main stream Video Icon: Change the pairs of resolution and
quality which you already arranged in the ―Video‖ setting page.
Sub stream Video Icon: Change the pairs of resolution and
quality which you already arranged in the ―Video‖ setting page.
Snapshot: Click on the button to take a snapshot. The snapshot would display
in one new page while working effectively.
Click on the button to record a video clip. The icon will change to the red color
while working effectively. And the icon will be back to black color while you
click the second time to stop recording. At the same time, there would be one
prompt information display as below.
11 / 60
Click on the button to hide the operation menu. The main menu will display
while you click the second time.
Full Screen: Double Click the video display pictures to enter into the full screen
mode. The pictures would be back to normal size while you double click the second
time.
This page is used to adjust the video display image.
This page is used to set the relative parameters.
12 / 60
2.2 Image Setting
This chapter explains how to set the image and saving options on the local computer.
2.2.1 Image Appearance
Please follow the steps below to change the ―Image Appearance‖ function through the
network as necessary.
1. Click on the ―Image Appearance‖ item on the right side of the ―Image‖ page to
unfold this page.
2. Click the symbol ―-‖ to decrease, click the symbol ―+‖ to increase. The button
default position is ―128‖, range from ―0-255‖, shift unit is ―1‖. The setting would
be working while you do the modification.
Brightness: An adjustable setting to compensate for backlit scenes.
Contrast: The measurement for color intensity/strength.
Sharpness: An adjustable setting to set the clarity of detail in the images.
Saturation: This setting controls the strength of colors from black and white to bold
2.2.2 Auto White Balance
White balance is the process of removing unnatural shades of color, so that objects
which appear white in reality are rendered white in the images.
13 / 60
Auto White Balance Close Auto White Balance Open
Please follow the steps below to change the ―Auto White Balance‖ function through the
network as necessary.
1. Click on the ―Auto White Balance‖ item on the right side of the ―Image‖ page to
unfold this page.
2. The default icon status is off , and it would change to open
and work while you click to enable this function.
2.2.3 WDR/BLC
1. Wide dynamic backlight technology supports the image processing of
high-contrast and backlighting, which can fix the overexposure in bright areas and
increase the brightness and clarity in dark areas, thereby providing a clear picture
of the whole scene.
Wide Dynamic Range Close Wide Dynamic Range Open
2. Click on the ―BackLight‖ item on the right side of the ―Image‖ page to unfold this
page.
14 / 60
3. The default icon status is off , and it would change to open
while you click to enable this function.
4. BLC is a feature provided by the Digital Signal Processor (DSP) in a security camera
that optimizes exposure in the foreground and background of security video. It
splits the video scene into different regions, and uses a different exposure for each
of these regions. It corrects regions with extremely high or low levels of light to
maintain a normal and usable level of light for the object in focus.
5. Click on the ―BackLight‖ item on the right side of the ―Image‖ page to unfold this
page.
6. The default icon status is off , and it would change to open
while you click to enable this function.
2.2.4 Exposure Control
Exposure time is controlled in a camera by shutter speed and the illumination level by
the lens aperture. This option allows the user to choose the exposure time.
Please follow the steps below to change the ―Exposure Control‖ function through the
network as necessary.
Click on the ―Exposure Control‖ item on the right side of the ―Image‖ page to 1.
unfold this page, there are two modes Auto Exposure / Manual Exposure as
below.
Choose the ―Auto Exposure‖ mode to use, the default status is as below. 2.
15 / 60
There are two status of the ―Flicker Control‖ – 50hz / 60hz, the default status is 3.
―50hz‖. Click the button to unfold this page to choose.
There are nine status of the ―Max Shutter‖ – 1, 1/2, 1/8, 1/15, 1/20, 1/25, 1/30, 4.
1/50, 1/100, the default status is ―1/50‖. Click the button to unfold this page to
choose.
To adjust the ―Max Gain‖ Function. Click the symbol ―-‖ to decrease, click the 5.
symbol ―+‖ to increase. The button default position is ―5‖, range from ―0-10‖, shift unit
is ―1‖.
.
Choose the ―Manual Exposure‖ mode to use, the default status is as below. 6.
Click the symbol ―-‖ to decrease, click the symbol ―+‖ to increase. The button 7.
default position is ―1‖, range from ―1-10‖, shift unit is ―1‖.
2.2.5 Image Flip
To flip the camera’s lens. Please follow the steps below to change the ―Image Flip‖
function through the network as necessary.
1. Click on the ―Exposure Control‖ item on the right side of the ―Image‖ page to
unfold this page, there are four modes None / Horizontal / Vertical / Both as below.
2. Click the button to unfold this page to choose.
3. Choose the ―None‖ mode to use, the picture would be no changes.
4. Choose the ―Horizontal‖ mode to use, the picture would flip 180 degrees at X
Position. Below is the actual working scene.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/