1
CAUTION...............WARNING...............IMPORTANT
USE ONLY A PETERSON REAL FYRE G10 BURNER WITH THIS REAL FYRE LOG SET.
Important: Adequate spacing between the
logs is NECESSARY and MUST be
maintained. If carbon build up (sooting)
exists, correct log placement before
sooting becomes worse. If any sooting
occurs outside of the fi rebox (i.e. on
the walls), turn off unit immediately
and contact a qualifi ed professional
service technician.
WARNING: Use ONLY a Peterson Real Fyre
G10 burner with this Real Fyre gas log
set. Failure to do so may result in
property damage or personal injury,
and will void listings, certifi cations,
and invalidate claims made to RHP.
Contact your local Real Fyre dealer if you
need more information.
This instruction contains log set placement for these Real Fyre logs. You must position and maintain the log
layout as shown here to ensure proper operation of the burner system. Incorrect log installation could cause
fl ame impingement and improper combustion, resulting in soot and/or excessive by-products of combustion.
DO NOT add any additional embers for this installation. Any additional embers will cause unsafe operation.
Use these logs only with a Peterson G10 burner system.
If you experience an accumulation of black carbon (soot) on your logs it is an indication of incomplete
combustion and you must correct the log placement as instructed in this manual. If signifi cant sooting
continues, stop using this gas log set.
Please read these instructions completely and carefully.
This product is only warranted when used as part of a
Robert H. Peterson Co. unvented burner system.
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
LOG SET IMPORTANT INFORMATION
L-F2-123REV 0 - 1904081300
CHARRED ALPINE BIRCH LOG PLACEMENT INSTRUCTIONS
CHAB-24 shown
2
Failure to use a Peterson G10 burner may result in a DANGEROUS
situation and in property damage, personal injury or even death, will void
listings and certifi cations, and will void any insurance coverage by R.H.
Peterson Co. or our insurers.
CAUTION: Burn hazard! Logs will remain hot for some time after use.
If you need to reposition any log to maintain the proper layout,
use heat resistant gloves or allow logs adequate time to cool
before handling.
WARNING: This gas log set is for use with an R.H. Peterson Co. G10
burner (and parts) ONLY.
L-F2-123REV 0 - 1904081300
3
CHARRED ALPINE BIRCH LOG PLACEMENT INSTRUCTIONS (16/18" MODEL)
III
I
II
CHAB-16/18
PARTS LIST
All items for this log set are included in one (1) box.
CAUTION: Burn hazard! Logs will remain hot
for some time after use.
1
2
CHABL-15BR
CHABL-16/18BF
3
CHABL-8T
4
5
CHABL-10TR
CHABL-10TL
Place the rear log (log #1) as shown. Slide it forward
on the grate, against the main burner bracket. The
cutouts found on the underside of the log should
align over the grate fi ngers. ENSURE THE LOG
RESTS FLAT ON THE BURNER/GRATE.
2
2
Place the left and right front log pieces (log #2)
as shown. Slide them back on the grate, against
the main burner bracket. The cutouts found on the
underside of the two logs should align over the
grate fi ngers. ENSURE THE LOGS REST FLAT
ON THE BURNER/GRATE.
Ensure the rear and front logs are snug up against
the main burner bracket.
1
Logs snug against bracket
The underside of the bottom logs have cutouts and tabs that align over the burner. THE BOTTOM LOGS
MUST BE FULLY SEATED ON THE BURNER. Certain logs have notches on them to allow for the logs to
interlock in place.
6
WCAB-1
4
CHARRED ALPINE BIRCH LOG PLACEMENT INSTRUCTIONS (16/18" MODEL) (CONT.)
IV
V
Place the left middle log (log #3) as shown. The
log should lock in place over the logs below.
Place the right middle log (log #4) as shown. The
log should lock in place over the logs below.
Place the center top log (log #5) as shown. The
log should lock in place over the logs below.
After setting the logs into position as described above, ensure each is properly and fi rmly seated. The
vent-free gas log set will not function as intended if the logs are not correctly positioned. When placed
properly, the fl ames will not strike any portion of the logs. Periodically check the positioning of all logs to
ensure proper log placement and stability. If any fl ame is striking the logs, recheck log placement. Adjust
to conform with instructions. There should be no fl ame impingement on the logs.
3
5
4
15 model shown
Side viewFront view
1" (minimum)
Place the decorative wood chip in front of the valve, with at least
1" between it and the valve.
CAUTION: Ensure the wood chip is placed at least 1"
away from the valve to avoid overheating
and damage to the valve. If this minimum
requirement of 1" clearance is not possible,
DO NOT use the wood chip.
CAUTION: THE WOOD CHIP WILL BE HOT DURING AND
AFTER OPERATION.
6
VII
Final Log Placement
VI
5
CHARRED ALPINE BIRCH LOG PLACEMENT INSTRUCTIONS (24" & 30" MODELS)
III
III
IV
CAUTION: Burn hazard! Logs will remain
hot for some time after use.
CHAB-24 & CHAB-30
PARTS LIST
24" log set shown
1
2
4
3
5
6
24" - CHABL-19BR
30" - CHABL-21BR
24" - CHABL-24BF
30" - CHABL-30BF
All items for these log sets are included in one (1) box.
CHABL-11TL
CHABL-13T
Place the rear log (log #1) as shown. Slide it forward on
the grate, against the main burner bracket. The cutouts
found on the underside of the log should align over the
grate fi ngers. ENSURE THE LOG RESTS FLAT ON THE
BURNER/GRATE.
2
2
Place the left and right front log pieces (log #2) as shown.
Slide them back on the grate, against the main burner
bracket. The cutouts found on the underside of the two logs
should align over the grate fi ngers. ENSURE THE LOGS
REST FLAT ON THE BURNER/GRATE.
Ensure the rear and front logs are snug up against the main
burner bracket.
V
Place the left middle log (log #3) as shown. The log should
lock in place over the logs below.
Place the center middle log (log #4) as shown. The log
should lock in place over the logs below.
CHABL-11TR
7
CHABL-9T
CHABL-11T
1
Logs snug against bracket
3
4
The underside of the bottom logs have cutouts and tabs that align over the burner. THE BOTTOM LOGS
MUST BE FULLY SEATED ON THE BURNER. Certain logs have notches on them to allow for the logs to
interlock in place.
8
WCAB-1
6
After setting the logs into position as described above, ensure each is properly and fi rmly seated. The
vent-free gas log set will not function as intended if the logs are not correctly positioned. When placed
properly, the fl ames will not strike any portion of the logs. Periodically check the positioning of all logs to
ensure proper log placement and stability. If any fl ame is striking the logs, recheck log placement. Adjust
to conform with instructions. There should be no fl ame impingement on the logs.
CHARRED ALPINE BIRCH LOG PLACEMENT INSTRUCTIONS (24" & 30" MODELS) (CONT.)
Place the right middle log (log #5) as shown. The
log should lock in place over the logs below.
Place the right top log (log #6) as shown. The log
should lock in place over the logs below.
V
VI
Place the center top log (log #7) as shown. The
log should lock in place over the logs below.
6
7
5
15 model shown
Side viewFront view
1" (minimum)
Place the decorative wood chip in front of the valve, with at least
1" between it and the valve.
CAUTION: Ensure the wood chip is placed at least 1"
away from the valve to avoid overheating
and damage to the valve. If this minimum
requirement of 1" clearance is not possible,
DO NOT use the wood chip.
CAUTION: THE WOOD CHIP WILL BE HOT DURING AND
AFTER OPERATION.
8
VIII
II
Final Log Placement
VII
-
1
-
2
-
3
-
4
-
5
-
6
Real Fyre Charred Alpine Birch Log G10 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Real Fyre G9 Owner's manual
-
-
-
-
-
-
-
-
-