Bresser Replacement Extruder Nozzle for 3D Printer Owner's manual

Type
Owner's manual

This manual is also suitable for

Bresser Replacement Extruder Nozzle for 3D Printer is a high-quality replacement part that is designed to work with Bresser 3D printers. This nozzle is made of durable materials and is built to last. It is easy to install and can be used to replace a worn or damaged nozzle.

The Bresser Replacement Extruder Nozzle for 3D Printer is a great way to improve the performance of your 3D printer. This nozzle can help to improve the quality of your prints and reduce the amount of time it takes to print. It is also a great way to save money on replacement parts.

Bresser Replacement Extruder Nozzle for 3D Printer is a high-quality replacement part that is designed to work with Bresser 3D printers. This nozzle is made of durable materials and is built to last. It is easy to install and can be used to replace a worn or damaged nozzle.

The Bresser Replacement Extruder Nozzle for 3D Printer is a great way to improve the performance of your 3D printer. This nozzle can help to improve the quality of your prints and reduce the amount of time it takes to print. It is also a great way to save money on replacement parts.

Changing the nozzle
1. Press [Filament], then press [Change]. The extruder unit is
heated up.
Wait until the target temperature is reached.
2. Open the filament
compartment cover.
3
. Pull out the filament as shown in the
illustration.
Heating extruder...
200
/235
Cancel
Load
Change
Wait minimum 15 minutes until the extruder
and the nozzle have cooled down.
Power off the printer after all parts are
cooled down.
4. Push the clips (7) with one hand and pull
the nozzle (5) downwards out of the extruder
with the other hand.
5. Push the new nozzle into the extruder with
its plug (X) facing backwards until it is
firmly fixed.
5. Power on the printer and re-insert the filament
(see chapter “Changing the filament”).
Note
The nozzle is tightly fixed in the extruder.
Therefore wiggle back and forth a little if
necessary and pull strongly.
Make sure to push the clips the whole time.
Note
7
5
X
GB
German version on opposite page! · Deutsche Fassung umseitig!
Plus d'informations ou des traductions disponibles sur · Meer informatie of de beschikbare vertalingen onder
Informazioni esaustive o traduzioni disponibili su · Información completa o traducciones disponibles en · Informações
abrangentes ou traduções disponíveis em www.bresser.de/P2080201
Manual_2080201_Nozzle-Düse_en-de_BRESSER_v012020a.indd 1Manual_2080201_Nozzle-Düse_en-de_BRESSER_v012020a.indd 1 30.01.2020 10:07:0430.01.2020 10:07:04
DE
Bresser GmbH
Gutenbergstr. 2 · DE-46414 Rhede
Germany
www.bresser.de · [email protected]
Errors and technical changes reserved.
Irrtümer und technische Ändeerungen vorbehalten.
Manual_2080201_Nozzle-Düse_en-de_BRESSER_v012020a
Düse wechseln
1. [Filament] drücken, dann [Change] drücken. Der Druckkopf
beginnt mit dem Vorheizen.
Warten bis die Zieltemperatur erreicht ist.
2. Die Filament-
Fachabdeckung öffnen.
3
. Filament wie auf der Abbildung dar-
gestellt herausziehen.
Heating extruder...
200
/235
Cancel
Load
Change
Warten Sie mind. 15 Minuten, bis Druckkopf
und Düse abgekühlt sind.
Den Drucker nach dem Abkühlen aus-
schalten.
4. Die Clips (7) mit einer Hand zusammen-
drücken und mit der anderen Hand die Düse
(5) nach unten aus dem Druckkopf ziehen.
5. Die neue Düse mit dem Stecker (X) nach
hinten in den Druckkopf drücken, bis er
fest sitzt.
5. Den Drucker einschalten und das Filament
wieder einsetzen (siehe “Filament wechseln”).
Hinweise
Die Düse sitzt stramm im Druckkopf.
Daher ggf. etwas vor und zurück wackeln
und kräftig ziehen.
Die Clips dabei stets gedrückt halten.
Hinweise
7
5
X
Manual_2080201_Nozzle-Düse_en-de_BRESSER_v012020a.indd 2Manual_2080201_Nozzle-Düse_en-de_BRESSER_v012020a.indd 2 30.01.2020 10:07:0430.01.2020 10:07:04
  • Page 1 1
  • Page 2 2

Bresser Replacement Extruder Nozzle for 3D Printer Owner's manual

Type
Owner's manual
This manual is also suitable for

Bresser Replacement Extruder Nozzle for 3D Printer is a high-quality replacement part that is designed to work with Bresser 3D printers. This nozzle is made of durable materials and is built to last. It is easy to install and can be used to replace a worn or damaged nozzle.

The Bresser Replacement Extruder Nozzle for 3D Printer is a great way to improve the performance of your 3D printer. This nozzle can help to improve the quality of your prints and reduce the amount of time it takes to print. It is also a great way to save money on replacement parts.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI