Axas 0199-004 User manual

Brand: Axas

Model: 0199-004

Category: Security cameras

Type: User manual

This manual is also suitable for

AXIS 206 Family

Network Camera

User’s Manual

AXIS COMMUNICATIONS

<Product Name> Quick User’s Guide

About this Document

This manual is intended for administrators and users of the

AXIS 206\206M\206W Network Camera, and is applicable

for software release 4.20. It includes instructions for using

and managing the product on your network. Previous

experience of networking will be of use when using this

product. Some knowledge of UNIX or Linux-based systems

may also be beneficial, for developing shell scripts and

applications. Later versions of this document will be posted

to the Axis Website, as required. See also the product’s

online help, available via the Web-based interface.

Safety Notices Used In This Manual

Caution! - Indicates a potential hazard that can damage the

product.

Important! - Indicates a hazard that can seriously impair

operation.

Do not proceed beyond any of the above notices until you

have fully understood the implications.

Intellectual Property Rights

Axis AB has intellectual property rights relating to

technology embodied in the product described in this

document. In particular, and without limitation, these

intellectual property rights may include one or more of the

patents listed at http://www.axis.com/patent.htm and one

or more additional patents or pending patent applications

in the US and other countries.

This product contains licensed third-party software. See the

menu item “About” in the product’s user interface for more

information.

Legal Considerations

Camera surveillance can be prohibited by laws that vary

from country to country. Check the laws in your local

region before using this product for surveillance purposes.

Electromagnetic Compatibility (EMC)

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures: Re-orient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver. Connect the equipment to an outlet on a different

circuit to the receiver. Consult your dealer or an

experienced radio/TV technician for help. Shielded (STP)

network cables must be used with this unit to ensure

compliance with EMC standards.

USA - This equipment has been tested and found to

comply with the limits for a Class B computing device

pursuant to Subpart B of Part 15 of FCC rules, which are

designed to provide reasonable protection against such

interference when operated in a commercial environment.

Operation of this equipment in a residential area is likely to

cause interference, in which case the user at his/her own

expense will be required to take whatever measures may be

required to correct the interference.

Europe - This digital equipment fulfills the

requirements for radiated emission according to limit B of

EN55022/1998, and the requirements for immunity

according to EN55024/1998 residential, commercial, and

light industry.

Japan - This is a class B product based on the standard of the

Voluntary Control Council for Interference from Information

Technology Equipment (VCCI). If this is used near a radio or

television receiver in a domestic environment, it may cause

radio interference. Install and use the equipment according to

the instruction manual.

Australia - This electronic device meets the requirements of

the Radio communications (Electromagnetic Compatibility)

Standard 1998 AS/NZS 3548.

Equipment Modifications

This equipment must be installed and used in strict accordance

with the instructions given in the user documentation. This

equipment contains no user-serviceable components.

Unauthorized equipment changes or modifications will

invalidate all applicable regulatory certifications and approvals.

Radio Transmission Regulatory Information

(AXIS 206W)

This equipment generates and radiates radio frequency energy,

and must be installed and operated while maintaining a

minimum body-to-camera distance of 3 feet (1 meter).

Tested to comply with FCC Standards FOR HOME OR OFFICE

USE. This product must be installed and used in strict

accordance with the instructions given in the user

documentation. This Axis product complies with the following

radio frequency and safety standards:

Europe - EU Declaration of Conformity. This device complies

with the requirements of the R&TTE Directive 1999/5/EC with

essential test suites as per standards

EN 60950 Safety of Information Technology equipment:

ETS 300 328 Technical requirements for radio equipment

ETS 300 826 General EMC requirements for radio equipment

USA - Federal Communications Commission FCC

This device complies with Part 15 of FCC Rules. Operation of

the device is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference that may cause

undesired operation.

Canada - This device complies with RSS-210 of Industry

Canada. Operation is subject to the following conditions:

(1) This device may not cause interference, and

(2) this device must accept any interference, including

interference that may cause undesired operation of the device

Liability

Every care has been taken in the preparation of this manual.

Please inform your local Axis office of any inaccuracies or

omissions. Axis Communications AB cannot be held responsible

for any technical or typographical errors and reserves the right

to make changes to the product and manuals without prior

notice. Axis Communications AB makes no warranty of any

kind with regard to the material contained within this

document, including, but not limited to, the implied warranties

of merchantability and fitness for a particular purpose. Axis

Communications AB shall not be liable nor responsible for

incidental or consequential damages in connection with the

furnishing, performance or use of this material.

Trademark Acknowledgments

Acrobat, Adobe, Boa, Ethernet, IBM, Internet Explorer, LAN

Manager, Linux, Macintosh, Microsoft, Mozilla, Netscape

Navigator, OS/2, UNIX, Windows, WWW, Wi-Fi are

registered trademarks of the respective holders. Java and all

Java-based trademarks and logos are trademarks or

registered trademarks of Sun Microsystems, Inc. in the

United States and other countries. Axis Communications AB

is independent of Sun Microsystems Inc. UPnP™ is a

certification mark of the UPnP™ Implementers Corporation.

WPA is a trademark of the Wi-Fi Alliance.

Support

Should you require any technical assistance, please contact

your Axis reseller. If your questions cannot be answered

immediately, your reseller will forward your queries through

the appropriate channels to ensure a rapid response. If you

are connected to the Internet, you can:

• download user documentation and firmware updates

• find answers to resolved problems in the FAQ database.

Search by product, category, or phrases

• report problems to Axis support by logging in to your

private support area

• visit Axis Support at www.axis.com/techsup/

AXIS 206 Network Camera Family - User’s Manual

Revision 2.0

Part No: 23617

March 2005

AXIS 206

Contents

About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Product Family Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

AXIS 206M - Additional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

AXIS 206W - Additional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Overview AXIS 206/206M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Overview AXIS 206W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Install the AXIS 206/206M. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Set the IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

One-click Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

UPnP™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

AXIS IP Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Manual Installation with ARP/Ping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Install the AXIS 206W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Set up the wireless connection - Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Discover the IP address for the AXIS 206W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Set up the AXIS 206W on other operating systems. . . . . . . . . . . . . . . . . . . . . . . . . 16

Access the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Access From a Browser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Select the language and password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Access from the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Focusing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

The Live View Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Image and Layout Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Overview of the Setup tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Image Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Live View Config - Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Live View Config - HTML Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Date & Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Network - Basic TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Network - Advanced TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

AXIS 206

Wireless Settings (AXIS 206W only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

SMTP (email). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

UPnP™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

LED Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

AXIS 206 - About this manual

About this manual

This user’s manual is valid for all camera models included in the AXIS 206 family of

network cameras. All text in the manual applies to all models, except where otherwise

indicated. Apart from their names, the AXIS 206 and the AXIS 206M are identical in

appearance.

Product Family Features

The network cameras included in the AXIS 206 product family are:

• The AXIS 206 Network Camera

• The AXIS 206M Megapixel Network Camera

• The AXIS 206W Wireless Network Camera

All models share the following features:

• Live high-quality video over the network, with images provided as a real-time

Motion JPEG stream. Multiple resolutions are available.

• Built-in Web server, providing full access to all features and setup tools, via a

standard web browser. For advanced functionality, the camera can be accessed

via the AXIS HTTP API (more info at www.axis.com/developer).

• Support for multiple viewers.

• NAT-Traversal, which allows a camera located on an intranet (LAN) to be made

available from the other (WAN) side of a NAT router.

• Support for other languages. Simply select a language from the available options.

The camera’s entire web interface is then displayed in the selected language.

• Upgradeable firmware.

• Support for UPnP™

UPnP™ is a certification mark of the UPnP

™

Implementers Corporation.

AXIS 206 - Product Family Features

AXIS 206M - Additional Features

The AXIS 206M Megapixel Network Camera has the

following additional features:

AXIS 206/206M

• 6 different video resolutions available.

• Maximum resolution 1280 x 1024 pixels.

• HDTV (High Definition TV) format available

(16:9 format, 1280x720 pixels).

AXIS 206W - Additional Features

AXIS 206W

The AXIS 206W Wireless Network Camera has the

following additional features:

• Built-in wireless module supporting the IEEE

802.11b standard, for access to wireless networks

• WPA-PSK and WEP (64 or 128-bit) encryption for

secure communication between camera and

network

• Multiple resolutions, up to 640x480 pixels (VGA

format), with a frame rate of up to 30 frames per

second in all resolutions.

AXIS 206 - Overview AXIS 206/206M

Overview AXIS 206/206M

Front

Focus

ring

Status

indicator

(outer ring)

Rear panel

Lock

Network

Serial number label

connector

Power

connector

Power

indicator

Control

button

Network

indicator

ring

Power Cable

clip

Power Connector - For connection of the PS-H or PS-L power adapter (included).

Network Connector - The AXIS 206/206M connects to the network via a standard RJ45

connector and automatically detects the speed of the local network segment

(10BaseT/100BaseTX Ethernet).

Serial Number - This may be required during installation.

Control Button - Press this button to install using the AXIS Internet Dynamic DNS Service

(see

page 11) or to restore the factory default settings, as described on page 36.

AXIS 206 - Overview AXIS 206W

Overview AXIS 206W

Status

indicator

Focus

ring

Wireless module

power indicator

Network traffic

Wireless module

(outer ring)

indicator

Front

Power connector

Control button

Power

Serial number

Power cable

USB connector

indicator

label

Mounting

lock ring

Wireless

clip

module

Rear panel

Power Connector - For connection of the PS-H or PS-L power adapter (included).

USB Connector - For connection of the supplied USB cable, used for the initial

configuration of the wireless network connection.

Serial Number - This may be required during installation.

Control Button - Press this button to install using the AXIS Internet Dynamic DNS Service

(see

page 11) or to restore to the factory default settings, as described on page 36.

AXIS 206 - LED Indicators

LED Indicators

After completion of the startup and self test routines, the multi-colored Network, Status,

and Power LED indicators flash as follows:

Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.

Green Steady for connection to 100 Mbit/s network. Flashes for network activity.

Red Flashes rapid red, together with the Status indicator, for hardware error.

Unlit No connection.

Green Shows steady green for normal operation. Can be configured to flash green at intervals

whenever the camera is accessed. See the online help for more information.

Unlit When configured for “no flash” on camera access.

Amber Shows steady amber during reset to factory default or when restoring settings.

Red Slow flash for failed upgrade (see Emergency Recovery Procedure, on page 40.)

Rapid flash, together with the Network indicator, for hardware error.

Green Normal operation.

Amber Flashes green/amber during firmware upgrade.

AXIS 206 & AXIS 206M

AXIS 206W

Blue Steady blue when wireless module has power.

Amber Flashes for traffic on wireless network.

Unlit No network traffic.

Green Shows steady green for normal operation. Can be configured to flash green at intervals

whenever the camera is accessed. See the online help for more information.

Unlit When configured for “no flash” on camera access.

Amber Shows steady amber during reset to factory default or when restoring settings.

Red Please contact Axis support at www.axis.com/techsup

Green Normal operation.

Amber Flashes green/amber during firmware upgrade.

Note that the Network indicators LEDs (power and traffic) for the AXIS 206W are located

on the front of the wireless module. Note also that these LEDs cannot be switched off.

Network

Status

Power

Network

(power)

Network

(traffic)

Status

Power

AXIS 206 - Mounting

Mounting

1. If required, use the 3 supplied screws to fix the base plate to

a flat surface.

2. To use the shorter stand, e.g. for wall mounting, unscrew

the lock ring to release the camera, and remove the

extension section.

3. Re-attach the camera, adjust the angle and gently tighten

the lock ring.

Important!

Install the AXIS 206/206M

Follow the steps below to install the AXIS 206/206M on your local network (LAN). To

install the AXIS 206W, please see

page 15.

1. Using the self-adhesive strip, attach the supplied cable clip to the rear panel.

2. Position and mount the camera as required - see above.

3. Connect the power adapter to the camera.

4. Fasten the power cable in the cable clip. This helps prevent accidental cable

disconnection.

5. Connect the AXIS 206/206M to the network using a standard RJ-45 network cable.

6. Select a method for setting the IP address - see the following page.

The AXIS 206 (all models) is designed for indoor use only, and must always be positioned where it is

not exposed to direct sunlight or strong halogen light, which can cause permanent damage to the

camera’s image sensor. Damage as a result of exposure to strong light is not covered by the Axis

warranty.

Lock ring

Wall mounting

AXIS 206 - Install the AXIS 206/206M

Set the IP address

The AXIS 206/206M is designed for installation on an Ethernet network. This involves

assigning it an IP address, automatically (via e.g. DHCP) or manually. Several methods are

available. The one to use depends on how your network is configured. If unsure of the

method to use, please consult your network administrator, or see the network’s

documentation.

• If you are using e.g. a home broadband router, you may find it convenient to view the

router’s administration pages to discover which IP address has been assigned to your AXIS

206/206M. Please consult the router’s documentation for further information.

• If your network has an Internet connection (with no HTTP proxy) and uses a DHCP server

to assign IP addresses, use the One-Click installation procedure. See

page 11.

• If your network uses automatic IP addressing (DHCP) and your computer uses the UPnP

service, the AXIS 206/206M will automatically be detected and displayed on your screen.

See

page 12 for more information.

•Use AXIS IP Utility (see page 13) to discover the IP address. This can also be used to set

the IP addess manually.

• Set the IP address manually with the ARP/Ping method, as described on page 14.

• The default static IP address for the AXIS 206/206M is 192.168.0.90

One-click Installation

Requirements:

Broadband router/modem pro-

viding automatic IP addressing

AXIS 206/206M (AXIS 206W via

wireless connection)

Internet

Computer

on a LAN

The AXIS Internet Dynamic DNS Service

• The One-click installation procedure uses the AXIS Internet Dynamic DNS Service. This free service allows you to quickly

and simply install your camera, which then receives a static name (DNS name). More information about the AXIS

Internet Dynamic DNS Service is available at www.axiscam.net

• Please note that this procedure will send the AXIS 206’s IP address, firmware version, product type and serial number to

the Axis Internet Dynamic DNS Service. No personal information is transferred.

• To remove the DNS name and unregister from the Axis Internet Dynamic DNS Service, open the Setup pages in the AXIS

206, click System Options > Network > TCP/IP, click the Settings button for the AXIS Internet Dynamic DNS Service

and finally, click the Remove button.

AXIS 206 - Install the AXIS 206/206M

Follow these instructions:

1. When the camera is connected to the power supply and the network, wait for the

Status Indicator on the front of the camera to show a steady green.

2. Now press the Control button on the rear of the camera once

. The Status indicator will

blink green while it connects to the AXIS Internet Dynamic DNS Service.

3. Wait for the Status indicator to go back to showing a steady green.

4. To complete the installation, now visit www.axiscam.net from an Internet connected

PC. This must be done within 60 minutes of pressing the Control button.

5. Follow the on-screen instructions provided by the AXIS Internet Dynamic DNS

Service. You will need your product’s serial number (see the label on the rear panel) to

complete the installation.

6. Please see page 17 for instructions on how to set the password.

UPnP™

UPnP

functionality is enabled by default in the AXIS 206. If also enabled on your computer

(Windows ME or XP), the camera will automatically be detected and a new icon will be

added to “My Network Places.” Click this icon to access the camera. See

page 19 for

instructions on how to set the password.

Notes:

UPnP

™

is a certification mark of the UPnP

™

Implementers Corporation.

•To install the UPnP service on your computer, open the Control Panel from the Start Menu and

select Add/Remove Programs. Select Add/Remove Windows Components and open the Net-

working Services section. Click Details and then select UPnP as the service to add.

•Once the AXIS 206 is accessible from your computer, it is then possible to use the One-click

installation method to provide the camera with a DNS name.

AXIS 206 - Install the AXIS 206/206M

AXIS IP Utility

AXIS IP Utility 2.0 is a free

Windows application that

discovers and displays Axis

devices

AXIS 206/206M (AXIS 206W via

wireless connection)

Computer

on a LAN

Hub/Switch

Requirements:

on your network. The

application can also be used to

manually set a static IP address.

AXIS IP Utility 2.0 is available

on the CD supplied with the

AXIS 206. Updated versions of AXIS IP Utility may be available at www.axis.com

Automatic discovery

1. When connected to the power supply and the network, wait for the Status Indicator on

the front of the camera to show a steady green.

2. Insert the CD into your computer’s CD drive.

3. Start AXIS IP Utility. When the AXIS 206 appears in the window, double-click it to

open its home page. If the camera is not accessible, this might be because its IP address

is not valid on that network. Right-click on the camera to set the IP address manually.

Set the IP address manually

1. If the AXIS 206 does not appear in the window at all, click the Refresh button to try

again. If the camera still does not appear, you can set the IP address manually. Acquire

an unused IP address on the same subnet as your computer.

2. Click the button “Set IP address using serial number” and enter the serial number (see

page 10) and IP address for the AXIS 206. Follow the on

-screen instructions.

Note:

After using AXIS IP Utility, the AXIS 206 can be assigned a DNS name by using the AXIS Dynamic DNS

Service. See page 11.

AXIS 206 - Install the AXIS 206/206M

Manual Installation with ARP/Ping

1. Acquire an unused IP address for the AXIS 206/206M. This IP address must be on the

same subnet as your computer.

2. Locate the serial number (S/N) on the label on the camera’s rear panel.

3. From a computer on your network, open a Command Prompt (in Windows: from the

Start menu, select Run... and type cmd in the field. Click OK).

4. As appropriate for your operating system, enter the following commands:

5. Check that the network cable is connected (or that the wireless connection is

functioning). Start/restart the camera by disconnecting and reconnecting the power

cable.

6. Close the Command prompt when you see ‘Reply from 192.168.0.125: ...’

7. The IP address has been set when the Power indicator is permanently lit and the

Network indicator flashes intermittently.

8. Start your browser, enter the IP address of the camera in the Location/Address field and

press Enter on your keyboard. See below for instructions on how to set the password.

Note:

Windows syntax: Windows example:

arp -s <IP Address> <Serial Number>

ping -l 408 -t <IP Address>

arp -s 192.168.0.125 00-40-8c-18-10-00

ping -l 408 -t 192.168.0.125

UNIX/Linux/Mac syntax: UNIX/Linux/Mac example:

arp -s <IP Address> <Serial Number> temp

ping -s 408 <IP Address>

arp -s 192.168.0.125 00:40:8c:18:10:00 temp

ping -s 408 192.168.0.125

After installation, the AXIS 206 can be assigned a DNS name by using the AXIS Dynamic DNS Service.

See page 11.

AXIS 206 - Install the AXIS 206W

Install the AXIS 206W

Before the AXIS 206W can connect to an encrypted wireless network, the wireless settings

in the camera must be configured and an IP address must be set. This is done by

connecting the camera to a computer with the help of the supplied USB cable. Follow the

instructions below.

Set up the wireless connection - Windows

1. Connect the power adapter to the camera. Press the power cable into the cable clip on

the rear panel. This will help prevent accidental cable disconnection.

2. Connect the USB

cable to your

computer and then

to the camera.

3. Open My Computer

or Windows

Explorer, and the

AXIS 206W should

be displayed as a

new drive.

4. Click on the drive

for the AXIS 206W to see the files contained in the camera.

5. Click on the file setup.exe. This starts

the AXIS Setup Tool, which lets you

configure the wireless settings.

6. Enter the name of the network (SSID) to

connect to, and optionally enable

wireless encryption. See the online help

in the setup tool for more information.

Note that any settings made here should

match those previously made in your

wireless access point.

7. Specify the type of IP address to use.

See the online help for more

information.

8. Click OK, close the AXIS Setup Tool and

disconnect the USB cable.

The AXIS 206W displays

as a drive

Online Help

AXIS 206 - Install the AXIS 206W

9. Wait at least 10 seconds for the settings to take effect and then restart the camera by

disconnecting and reconnecting the power cable.

Discover the IP address for the AXIS 206W

If you set the IP address manually, you can now access the camera’s web interface simply

by starting a browser and entering the IP address.

If you selected Obtain IP address via DHCP, you have several options:

• Reconnect the USB cable, browse to the camera as before, and restart the AXIS Setup Tool.

The DHCP-assigned address will be displayed in the tool.

• If you are using e.g. a home broadband router, you may find it convenient to view the

router’s administration pages to discover which IP address has been assigned to your AXIS

206W. Please consult the router’s documentation for further information.

• If your network has an Internet connection (with no HTTP proxy), use the AXIS Dynamic

DNS Service to assign your camera a DNS name, which is then used to access the camera.

See

page 11 for more information.

• If your network uses automatic IP addressing (DHCP) and your computer uses the UPnP

™

service, the AXIS 206W will automatically be detected and displayed on your screen.

• Use AXIS IP Utility 2.0 to discover the IP address. See the CD included with the product.

Set up the AXIS 206W on other operating systems

To set up the AXIS 206W on other operating systems (Linux/Unix/Mac), follow these steps:

1. Connect the camera to the computer via the USB cable. This allows you to access the

camera as a USB Mass Storage device.

2. Browse to and open the file config.txt and enter the encryption keys, the SSID network

name, the IP address, etc. The wireless settings entered here should be identical to those

previously configured in your wireless access point.

3. Save the file, wait at least 10 seconds for the settings to take effect and then restart the

camera to enable the wireless connection.

AXIS 206 - Access the Camera

Access the Camera

Access From a Browser

The AXIS 206 can be used with most standard operating systems and browsers. The

recommended browser is Internet Explorer with Windows, or Mozilla/Firefox with other

operating systems. See also the

Technical Specifications, on page 37.

1. Start a browser (e.g. Internet

Explorer, Mozilla)

2. Enter the IP address or host name

of the AXIS 206 in the

Location/Address field of your

browser.

Select the language and password

1. When accessing the AXIS 206 for the first time you can optionally change the

language. Select the language from the available options, by clicking the appropriate

flag.

2. The next step is to set the password for the

user “root.” Enter a password and then

re-enter it to confirm the spelling. Click OK.

3. The ‘Enter Network Password’ dialog will

appear. Enter the user name: root

4. Enter the password as set in step 2 above, and click OK. If the password is lost, the

AXIS 206 must be reset to the factory default settings. See below.

5. If required, click Yes to install the AXIS Media Control (AMC). You will need

administrator rights on the computer to do this.

Notes: •The default administrator user name root is permanent and cannot be deleted.

•The language can be changed at any time via the Setup link available from the product’s web

interface.

AXIS 206 - Access the Camera

The Live View page of the AXIS 206 is now displayed, with links to the Setup tools that

allow you to customize the camera to your specific needs.

Live View - Shows live video

from the camera.

Setup - Provides all the tools

needed to set up the camera to

your requirements.

Help - Displays online help on

all aspects of using the camera.

Notes: •To view streaming video in Microsoft Internet Explorer, you must set your browser to allow

ActiveX controls and allow the AXIS Media control (AMC) to be installed on your workstation. If

your workstation restricts the use of additional software components, the AXIS 206 can be con-

figured to use a Java applet for updating images. Please see the online help for more informa-

tion.

•The layout of the web pages in the AXIS 206 may have been customized to meet specific

requirements. Consequently, some of the examples and functions featured here may differ from

those displayed on your own Live View page.

Access from the Internet

Once installed, your AXIS 206 is accessible on your local network (LAN). To access the

camera from the Internet you must configure your router to allow incoming data traffic to

the camera. To do this, enable the NAT-traversal feature, which will attempt to

automatically configure the router to allow access to the camera. This is enabled from

Setup > System Options > Network > TCP/IP Advanced.

For more information, please see NAT traversal (port mapping), on page 31. See also the

AXIS Internet Dynamic DNS Service at www.axiscam.net or, for Technical notes on this

and other topics, visit the Axis Support Web at www.axis.com/techsup

AXIS 206 - Focusing

Focusing

To focus the AXIS 206, see the illustration below.

Status Indicator

Focus Ring

To focus:

Open a browser and

examine the image. If

required, adjust the focus

ring until the focus is

satisfactory.

The focus ring features a

raised line.

A small dot is located over the

top of the lens assembly.

Notes: •Upon delivery, the raised line is aligned with the dot above the lens, and the focus is set to

infinity. After a focus adjustment, the raised line might not be aligned with the dot. This is not

important.

•Although the illustration shows the AXIS 206W, the focusing procedure is identical for all

models.

Page is loading ...

Axas 0199-004 User manual

Brand: Axas

Model: 0199-004

Category: Security cameras

Type: User manual

This manual is also suitable for

Download PDF

report

Axas 0199-004 User manual

This manual is also suitable for

Axas 0199-004 User manual

Other documents