Whirlpool WA PL 974 FLD Installation guide

Brand: Whirlpool

Model: WA PL 974 FLD

Category: Washing machines

Type: Installation guide

Check the preset detergent dosing value and adapt it to your detergents if necessary (Detergent calibration)

Important: during this phase do not consider the local water hardness; simply follow the instructions below.

There are three different basic dosing values which are preset:

• one for programme group Wool/Handwash and Delicates

• one for programme Dark

• one for all other programmes

Press and hold the buttons marked with and “+” simultaneously for at least 3 seconds.

On the display, the symbol for the “soft” water hardness level blinks:

Press the button marked with “+” to select “medium” water hardness:

r “hard” water hardness:

If you want to reduce the selected water hardness level,

press the button marked with "-".

Confirm the selected water hardness by pressing the button marked with “Ok”.

…for a certain programme group:

Select any programme belonging to the group you want to reset the do-

sing value for.

Press the button marked with for at least 3 seconds -" the bottle sym-

bol and the saved detergent value appear on the display.

Press the “Reset/Drain” button – “rES” shortly appears on the display.

Afterwards, the default dosing value appears on the display.

Press the button marked with “Ok” to confirm and exit.

…for all programmes:

Select programme “Rinse & Spin”.

Press the button marked with for at least 3 seconds -" the bottle sym-

bol and “---” appear on the display.

Press the “Reset/Drain” button – “rES” appears on the display

Press the button marked with “Ok” to confirm and exit.

Dosing Aid - before the first use...

Check if the water hardness degree "soft" preset in the washing machine matches your regional

ater hardness. Also check if the dosing amounts recommended on your detergent packs corre-

spond with the preset basic dosing amounts of the washing machine.

= soft

= medium

= hard

If you want to reset the dosing values you saved and go back to the default values…

Adapt the preset water hardness if necessary

The water hardness of your washing machine is set to "soft". Check with your regional water supply authorities or by using the test stripe provided

with your washing machine, if the hardness of your water is also "soft". Refer to the picture on the right to understand how to interpret results from

the stripe test. If your regional water hardness is not "soft", adapt the water hardness setting of the washing machine as follows

Do this for all three programme groups mentioned above; it is sufficient to save a dosing value for ONE programme per group - it will be auto-

matically saved for the other programmes of this group. For example: if you save the dosing value for “Wool/Handwash”, it will be automatically

saved for “Delicates”, too.

If you want to change the saved dosing values (because you changed the type of detergent you use, for example)

…proceed as described above; the previously saved dosing value will be replaced by the new one for the programme group you selected.

To check and eventually change the preset detergent dosing value, proceed as follows:

First select a programme belonging to the group for which you want to check the preset dosing value.

Use amount for

medium soil level

and medium water

hardness recom-

mended on your

detergent pack.

Press the button marked with for at least 3 seconds - the bottle symbol on the

display lights up, and the preset detergent dosing value blinks on the display.

If the dosing amount recommended on your detergent pack (for medium water hard-

ness and medium soil level) is a different one, change the dosing value of the wash-

ing machine now by pushing the buttons marked with “+” or “-”.

Press button marked with “Ok” to save the set detergent dosing value - the numbers

stop blinking, and shortly afterwards the display will go back to the initial state.

10601461GB.qxp:Layout 1 12-05-2010 15:40 Pagina 1

oad the laundry, close the door and select the desired programme.

Select any options, change temperature and spin speed if you want, adjust the soil level and set a start delay, if desired.

Note that…

•

you must set any options and the start delay BEFORE you press the “Start (Pause)” button for the first time (before step ).

•

the durations for programmes with small maximum loads (like Delicates, Wool, Handwash etc., see in separate programme chart) are not up-

dated when you press the “Start (Pause)” button for the 2nd time (step ).

•

the programme duration can differ from the time which is indicated on the display after the wash load has been identified. It can be influenced

also by factors like reduced inlet water temperature, which leads to a longer heating time. While the programme duration is newly calculated,

the display shows an animation.

•

if you want to add more laundry after you have already pressed the “Start (Pause)” button for the first time (step ), proceed as follows:

press the “Reset/Drain” button for at least 2 seconds: the door will unlock after a while, and you can add the laundry.

Close the door and just press the “Start (Pause)” button again; the washing machine will repeat the load estimation and display the dosing

value accordingly.

• if you load the drum with laundry which is already wet, do not use the full amount of detergent the "Dosing Aid" function recommends you,

but only 2/3 of the recommended amount.

Dosing Aid - how to use it...

our washing machine is “intelligent”: it will calculate the recommended detergent quantity for the selected programme, depending on the soil

level of your laundry and the size of your wash load. It will also adapt the programme duration, water and energy consumption accordingly.

Whirlpool is a registered trademark of Whirlpool, USA

5019 106 01461

01/10

Press the “Dosing Aid”

utton shortly – the light goes

on, and the “Dosing Aid” sym-

bol on the display lights up.

The recommended detergent

dosing value in ml appears on

the display:

Press the “Start (Pause)” button.

The door locks

If you have selected prewash, the display will alternately show

the detergent amount for the prewash chamber (marked with

“I”) and for the main wash chamber (marked with “II”) of the

detergent dispenser:

Prewash Main wash

Add the recommended deter-

gent quantity to the detergent

dispenser now.

Press the “Start (Pause)”

button again.

The washing machine calculates the programme time according to the identified wash load while the display shows an animation.

...and then the wash programme starts automatically.

The washing machine detects the wash load while the display shows an animation; this will last

approximately 10 seconds.

10601461GB.qxp:Layout 1 12-05-2010 15:40 Pagina 2

Whirlpool WA PL 974 FLD Installation guide

Brand: Whirlpool

Model: WA PL 974 FLD

Category: Washing machines

Type: Installation guide

Download PDF

report

Whirlpool WA PL 974 FLD Installation guide

Whirlpool WA PL 974 FLD Installation guide

Related papers