Hotpoint XAL85 T1I G WTD Operating Instructions Manual

Brand: Hotpoint

Model: XAL85 T1I G WTD

Type: Operating Instructions Manual

XH9 XXX X XX

English

Operating Instructions

REFRIGERATOR/FREEZER COMBINATION

Contents

Operating Instructions, 1

Assistance, 2

Description of the appliance, 3

Description of the appliance, 4

Installation, 5

Start-up and use, 5

Maintenance and care, 7

Precautions and tips, 7

Troubleshooting, 8

Reversible doors, 9

Assistance

Before calling for Assistance:

• Check if the malfunction can be solved on your own (see

Troubleshooting).

• If after all the checks, the appliance still does not operate or

the problem persists, call the nearest Service Centre

Communicating:

• type of malfunction

• appliance model (Mod.)

• serial number (S/N)

This information can be found on the data plate located on the

bottom left side of the refrigerator compartment.

Never call on unauthorized technicians and always refuse

spare parts which are not originals.

- model - serial number

Description of the appliance

Control panel

1. ON/OFF

The whole product (both fridge and freezer compartments)

can be turned on by pressing this button for 2 seconds.

The last set value is indicated on the interface. Press this button

to turn off the device. An audible signal will confirm the “off

commutation of the product”.

2. FRIDGE temperature indicator

It shows the temperature of the fridge compartment.

3. FRIDGE temperature setting

It allows you to change the fridge temperature value, in a

cyclical way; it also confirms the selected temperature on the

interface.

4 SUPER indicator light (rapid freezing)

illuminates when the SUPER button is pressed.

5 SUPER button (rapid freezing)

To be used to freeze fresh foods. When it is pressed, the

SUPER indicator light illuminates (see Start-up and use).

Description of the appliance

Overall view

The instructions contained in this manual are applicable to different

model refrigerators. The diagrams may not directly represent the

appliance purchased. For more complex features, consult the

following pages.

1 Levelling FEET

2 STORAGE compartment*

3 FREEZER and STORAGE compartment

4 FRUIT and VEGETABLE bin *

5 COMPARTMENT 3 IN 1 ZONE*

6 Control panel

7 WINE RACK *

8 SHELVES *

9 LAMP (see Maintenance).

10 Extractable STORAGE shelf WITH COVER

11 Removable multipurpose SHELVES *

12 BOTTLE shelf

13 WATER DISPENSER

* Varies by number and/or position, available only on certain

models.

Installation

! Before placing your new appliance into operation please read

these operating instructions carefully. They contain important

information for safe use, for installation and for care of the

appliance.

! Please keep these operating instructions for future reference.

Pass them on to possible new owners of the appliance.

Positioning and connection

Positioning

1. Place the appliance in a well-ventilated humidity-free room.

2. Do not obstruct the rear fan grills. The compressor and

condenser give off heat and require good ventilation to

operate correctly and save energy.

3. Leave a space of at least 10 cm between the top part of

the appliance and any furniture above it, and at least 5 cm

between the sides and any furniture/side walls.

4. Place the device far from heat sources (direct sun light,

electric kitchen etc.)

Levelling

1. Install the appliance on a level and rigid floor.

2. If the floor is not perfectly horizontal, adjust the refrigerator

by tightening or loosening the front feet.

Electrical connections

After the appliance has been transported, carefully place it

vertically and wait at least 3 hours before connecting it to the

electricity mains. Before inserting the plug into the electrical

socket ensure the following:

• The appliance is earthed and the plug is compliant with the

law.

• The socket can withstand the maximum power of the

appliance,

• The voltage must be in the range between the values indicated

on the data plate located on the bottom left side (e.g. 220-

240V).

• The socket is compatible with the plug of the appliance. If

the socket is incompatible with the plug, ask an authorised

technician to replace it (see Assistance). Do not use extension

cords or multiple sockets.

! Once the appliance has been installed, the power supply cable

and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these safety

measures not be observed.

Start-up and use

Starting the appliance

! Before starting the appliance, follow the installation

instructions (see Installation).

! Before connecting the appliance, clean the compartments and

accessories well with lukewarm water and bicarbonate.

! Electronic versions are provided with a motor protection switch

that powers on the compressor only almost 8 minutes after the

starting. The compressor also starts each time the power supply

is cut off whether voluntarily or involuntarily (blackout).

1. Connect the plug and check that the FRIDGE TEMPERATURE

indicator turns on. If the indicator stays off, please press the

ON/OFF button.

2. Set the FRIDGE TEMPERATURE on an average value. After

a few hours it will be possible to insert food in the fridge.

Cooling system

No Frost

The No Frost system circulates cold air continuously to collect

humidity and prevent ice and frost formation. The system

maintains an optimal humidity level in the compartment,

preserving the original quality of the food, preventing the food

from sticking together and making defrosting a thing of the past.

Do not block the aeration cells by placing food or containers in

direct contact with the refrigerating back panel. Close bottles

and wrap food tightly.

Using the refrigerator to its full potential

• Place only cold or lukewarm foods in the compartment•

Remember that cooked foods do not last longer than raw

foods.

• Do not store liquids in open containers: they will increase the

level of humidity in the refrigerator and cause condensation to

form.

COMPARTMENT 3 IN 1 ZONE*

This is the new box which offers maximum flexibility in order to

stock your food in an excellent way.

-store meat, fish and delicate food;

-rapid cooling of hot food from 70°C to 3°C and of other fresh

foods and leftovers

-low temperature defrosting (it inhibits the proliferation of

microorganisms).

You can get the 0°C temperature, in standard conditions, when

the fridge compartment temperature is at about 4°C.

By decreasing the fridge temperature you decrease the CHILLER

compartment temperature too.

* Varies by number and/or position, available only on certain

models.

SHELVES:

Due to the special guides the shelves are removable and the

height is adjustable allowing easy storage of large containers

and food. Height can be adjusted without complete removal of

the shelf. (see diagram),

TEMPERATURE Indicator light*: to identify the coldest area in

the refrigerator.

1. Check that OK appears clearly on the indicator light (see

diagram).

2. If the word “OK” does not appear it means that the temperature

is too high:set the FRIDGE TEMPERATURE on a colder value,

and then wait 10 hours until the temperature becomes stable.

3. Check the indicator light again: if necessary, readjust it

following the initial process. If large quantities of food have

been added or if the refrigerator door has been opened

frequently, it is normal for the indicator not to show OK. Wait

at least 10 hours before you set the FRIDGE temperature on

a colder value.

Operation and maintenance of the water

dispenser.

When first used, or after prolonged periods of inactivity, wash the

tank with water. The water dispenser supplies cold water without

having to open the refrigerator door each time.

This also allows for reducing the product’s energy consumption.

To fill the tank, lift the flap or remove the cover (see picture) then

pour in the water with a carafe or other suitable container. Avoid

filling the tank completely.

Always exclusively use drinkable natural mineral water: any

other liquid may hamper the device’s correct operation.

To withdraw water with the refrigerator door closed, press the

dispenser actuator with a suitable container (glass, carafe, etc.).

Release the actuator once the desired quantity has been dispensed.

The water tank should be cleaned regularly under running water; do

not use detergents. To clean the tank, remove the tank cover and

upper ledges; subsequently, remove the tank by pulling it outwards

while pressing the appropriate button (see picture).

The tank must be replaced back into its housing as soon as

possible so as to avoid excessive heating of the refrigerator.

For more thorough cleaning, it is advisable to unscrew the valve

from the tank (see picture) and clean it under running water.

! Be careful not to pull the transparent mobile element of the valve.

Once cleaning operations have been completed, screw the

valve back on while ensuring that the internal seal adheres to the

end part of the tank bushing; subsequently, put the tank-valve

assembly back into the appropriate cylindrical housing of the

door, while making sure that the upper hook on the rear wall of

the tank is properly inserted in the appropriate compartment on

the inner wall of the door. Put the previously removed ledges and

tank cover back in place.

! Make sure that the tank has been properly inserted in the

door (see picture).

! The presence of water drops on the tank walls is a normal

occurrence during the product’s operation.

! Dry any drops present on the outer walls of the product.

! To empty completely the Water Tank, please disassembly

it as shown on the picture, spill the water, clean with a soft

textile and assembly in the product.

! If the water drops remain on the external door surface

after use, clean it with a soft cleaning textile.

Using the freezer to its full potential

• Do not re-freeze food that is defrosting or that has already been

defrosted. These foods must be cooked and eaten (within 24

hours).

• Fresh food for freezing should not be placed in contact with

the one already frozen; it should be placed in the lower

FREEZER and STORAGE compartment that provides the best

freezing rate.

• To freeze fresh food in the best and safest way possible,

activate the SUPER function 24 hours before placing the

food in the freezer. After placing the food inside, activate the

SUPER function again; it will be deactivated automatically

after 24 hours;

• Do not place glass bottles which contain liquids, and which are

corked or hermetically sealed in the freezer because they could

break.

• The maximum quantity of food that may be frozen daily is

indicated on the plate containing the technical properties

located on the bottom left side of the refrigerator compartment

(for example: 2Kg/24h ).

! To avoid blocking the air circulation inside the freezer

compartment, it is advisable not to obstruct the ventilation

holes with food or containers.

! Do not open the door during freezing.

! If there is a power cut or malfunction, do not open the freezer

door. This will help maintain the temperature inside the

freezer, ensuring that foods are conserved for at least 12-18

hours.

! To get more space inside your freezer, you can take out any

drawers (and flaps, if appropriate), from their slots, by putting

your food directly on the provided shelves.

Maintenance and care

Switching the appliance off

During cleaning and maintenance it is necessary to disconnect

the appliance from the electricity supply:

1. Press the ON/OFF button to turn off the device

2. pull the plug out of the socket

Cleaning the appliance

• The external and internal parts, as well as the rubber seals

may be cleaned using a sponge that has been soaked in

lukewarm water and bicarbonate of soda or neutral soap. Do

not use solvents, abrasive products, bleach or ammonia.

• The removable accessories may be soaked in warm water

and soap or dishwashing liquid. Rinse and dry them carefully.

• The back of the appliance may collect dust which can be

removed by delicately using the hose of a vacuum cleaner set

on medium power. The appliance must be switched off and

the plug must be pulled out before cleaning the appliance.

Avoiding mould and unpleasant odours

• The appliance is manufactured with hygienic materials which

are odour free. In order to maintain an odour free refrigerator

and to prevent the formation of stains, food must always be

covered or sealed properly.

• If you want to switch the appliance off for an extended period

of time, clean the inside and leave the doors open.

Replace LED * light

The LED lighting, thanks to the powerful diffused light, allows

a clear view of each food. If you need to replace the LED light,

contact theTechnical Service.

Replacing the light bulb *

To replace the light bulb in the refrigerator compartment, pull out

the plug from the electrical socket. Follow the instructions below.

Access the light bulb by removing the cover as indicated in the

diagram. Replace it with a similar light bulb within the power

range indicated on the cover.

Precautions and tips

! The appliance was designed and manufactured in compliance

with international safety standards. The following warnings are

provided for safety reasons and must be read carefully.

This appliance complies with the following Community Directives:

- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent

amendments;

-89/336/EEC of 03.05.89 (Electromagnetic Compatibility) and

subsequent amendments;

- 2002/96/CE.

General safety

• The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial use.

• The appliance must be used to store and freeze food products

by adults only and according to the instructions in this manual.

• The appliance must not be installed outdoors, even in covered

areas. It is extremely dangerous to leave the appliance

exposed to rain and storms.

• Do not touch the appliance with bare feet or with wet or moist

hands and feet.

• Do not touch the internal cooling elements: this could cause

skin abrasions or frost/freezer burns.

• When unplugging the appliance always pull the plug from the

mains socket, do not pull on the cable.

• Before cleaning and maintenance, always switch off the

appliance and disconnect it from the electrical supply. -It is

not enough to turn off the device (with the ON/OFF button)

to eliminate all electric contacts.

• In the case of a malfunction, under no circumstances should

you attempt to repair the appliance yourself. Repairs carried

out by inexperienced persons may cause injury or further

malfunctioning of the appliance.

• Do not use any sharp or pointed utensils or electrical

* Varies by number and/or position, available only on certain

models.

equipment - other than the type recommended by the

manufacturer - inside the frozen food storage compartments.

• Do not put ice cubes taken directly from the freezer into your

mouth.

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or lack of experience

and knowledge unless they have been given Supervision

or instruction concerning use of the appliance by a person

responsible for their safety. Children should be Supervised

to ensure that they do not play with the appliance.

• Keep packaging material out of the reach of children! It can

become a choking or suffocation hazard.

Disposal

• Observe local environmental standards when disposing

packaging material for recycling purposes.

• The European Directive 2012/19/EU on Waste Electrical and

Electronic Equipment (WEEE), requires that old household

electrical appliances must not be disposed of in the normal

unsorted municipal waste stream. Old appliances must

be collected separately in order to optimise the recovery

and recycling of the materials they contain and reduce the

impact on human health and the environment. The crossed

out “wheeled bin” symbol on the product reminds you of your

obligation, that when you dispose of the appliance it must be

separately collected. Consumers should contact their local

authority or retailer for information concerning the correct

disposal of their old appliance.

Respecting and conserving the

environment

• Install the appliance in a fresh and well-ventilated room.

Ensure that it is protected from direct sunlight and do not

place it near heat sources.

• Try to avoid keeping the door open for long periods or opening

the door too frequently in order to conserve energy.

• Do not fill the appliance with too much food: cold air must

circulate freely for food to be preserved properly. If circulation

is impeded, the compressor will work continuously.

• Do not place hot food directly into the refrigerator. The internal

temperature will increase and force the compressor to work

harder and will consume more energy.

• Defrost the appliance if ice forms (see Maintenance). A thick

layer of ice makes cold transference to food products more

difficult and results in increased energy consumption.

Troubleshooting

If the appliance does not work, before calling for Assistance (see

Assistance), check for a solution from the following list.

The interface is off.

• The plug is not inserted in the outlet, or it is not powerful enough

to create a contact, or there is no electricity in the house.

The motor does not start.

• The appliance comes with a motor protection control (see

Start-up and use).

a) The alarm sounds.

a) The refrigerator door has remained open for more than two

minutes (the buzzer will stop sounding when you shut the door)

or the correct switching-off procedure was not followed (see

Maintenance).

The refrigerator and the freezer do not cool well.

• The doors do not close properly or the seals are damaged.

• The doors are opened too frequently.

• The FRIDGE TEMPERATURE is not correct (see Description).

• The refrigerator or the freezer have been over-filled.

The food inside the refrigerator is beginning to freeze.

• The FRIDGE TEMPERATURE is not correct (see Description).

• The food is in contact with the back inside wall of the

refrigerator.

The motor runs continuously.

• The SUPER button was pressed: the yellow SUPER indicator

is on (see Description).

• The door is not closed properly or is continuously opened.

• The outside ambient temperature is very high.

The appliance makes a lot of noise.

• The appliance has not been installed on a level surface (see

Installation).

• The appliance has been installed between cabinets that

vibrate and make noise.

• The internal refrigerant makes a slight noise even when the

compressor is off. This is not a defect, it is normal.

The back wall of the refrigerator unit is covered in frost or

droplets of water

• This shows the appliance is operating normally.

400011182421

09/2017

Hotpoint XAL85 T1I G WTD Operating Instructions Manual

Hotpoint XAL85 T1I G WTD Operating Instructions Manual

Hotpoint XAL85 T1I G WTD Operating Instructions Manual

Related papers

Other documents