2. Tascam
  3. RC-SS150
RC-SS150

Tascam RC-SS150 User manual

  • Hello! I am an AI chatbot trained to assist you with the Tascam RC-SS150 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I check the firmware version of the RC-SS150?
    How do I update the RC-SS150 firmware?
    What is the purpose of the PAGE [MENU] − and + buttons?
    What is the purpose of the MULTI JOG dial?
    What is the purpose of the SYSTEM item?
TASCAM
RC-SS150
1
RC-SS150
Checking the firmware version
Before starting firmware update procedures, check the firmware version of the RC-SS150 you are using.
1. Use the RS-232C connection cable included with the
RC-SS150 to connect it with a SS-CDR250N/SS-R250N.
CAUTION
Always turn the SS-R250N/SS-CDR250N unit power off
before connecting or disconnecting the cable.
Connecting and disconnecting while the power is on
could cause malfunction.
2. Turn the SS-R250N/SS-CDR250N unit on.
3. Press the PAGE [MENU] − and + buttons at the same
time to open the MENU screen.
4. If the firmware version of the system shown here is
the same or newer than the firmware version that you
plan to use for the update, there is no need to update.
Firmware update procedures
NOTE
The RC-SS150 firmware update uses the USB flash drive
or SD card of the connected SS-R250N/SS-CDR250N.
Updating is not possible using a CD (SS-CDR250N only).
1. Download the latest firmware from the TEAC Global
Site (http://teac-global.com/).
Decompress the downloaded file if it is in ZIP format
or another compressed file type.
2. Copy the downloaded firmware to the root folder (top
level of the medium).
3. Load the medium prepared in step 2 in an SD card
slot or the USB port on the front of the SS-R250N/SS-
CDR250N.
4. Set that medium as the current medium on the MEDIA
SELECT screen of the SS-R250N/SS-CDR250N.
5. Select UPDATE on the SYSTEM 2 page of the SS-R250N/
SS-CDR250N to open the FIRMWARE UPDATE screen.
SYSTEM item
This updates the SS-R250N/SS-CDR250N firmware.
FPGA item
Update the FPGA of the SS-R250N/SS-CDR250N.
RC-SS150 item
Update the firmware of a TASCAM RC-SS150 re-
mote control.
DRIVE item(SS-CDR250N only)
Update the CD drive firmware of an SS-CDR250N.
6. Select the RC-SS150 item, and press the MULTI JOG
dial on the SS-R250N/SS-CDR250N.
After the medium and firmware update file have been
verified, the following screen will appear.
NOTE
i
The screen above shows a list of firmware update files
in the root folder (top level) of the current medium. The
firmware copied in step 2 above should also be shown.
No Update File is shown if no update file is in the di-
rectory.
i
A maximum of five lines of firmware can be shown
at the same time. If there are more files than can be
shown on the display at once, use the MULTI JOG dial
on the SS-R250N/SS-CDR250N to scroll the list.
i
The screen shown above is an example. The actual ap-
pearance will differ.
072017
RC-SS150
2
TASCAM
RC-SS150
7. Select the firmware update to use.
The screen shown below will appear.
The number of the current version is shown on the
left and the update version is shown on the right.
The screen shown below will appear on the RC-SS150.
NOTE
The screen shown above is an example. The actual ap-
pearance will differ.
8. Press the MULTI JOG dial on the SS-R250N/SS-
CDR250N to start updating.
CAUTION
i
Be careful not to let the power be interrupted during
the update.
i
Do not load or remove media during the update.
i
If the power is interrupted or media is loaded or re-
moved during the update, the unit might become un-
startable.
9. When the update completes, the following message
will appear.
SS-R250N/SS-CDR250N screen
RC-SS150 screen
10. When the unit automatically turns off after the mes-
sage appears, turn it on again.
11. Confirm that the latest firmware is being used. This
completes the update procedure.
12. Delete the firmware update file from the medium.
/