Intel 945GZ User manual

User’s Manual

Intel 945GC/945GZ/945GCT/945GZT

Socket LGA775 Processor Mainboard

Intel 945 Series

Rev: 1.10, Oct 2007

P/N: 88EN945GC1

Disclaimer

The intellectual property of this manual belongs to our company. The ownership of all of the

products, including accessories and software etc. belong to our company. No one is permitted to

copy, change, or translate without our written permission.

We compiled this manual based on our careful attitude, but we can not guarantee the accuracy

of the contents. This manual is purely technical documentation, without any hint or other

meanings, and we won't commit users' misunderstanding of the typesetting error.

Our products are in continuous improvement and updating, Therefore, we retain the right that

we won't give notice to the users in future.

Copyright

All of the trademark in this manual belong to their own registered company.

All of the products name is only for identication, its title belongs to its manufacturer or brand

owner.

Table of Contents

Chapter 1 Introduction ........................................................................

3

1.1 Package Checklist ...............................................................................................

3

1.2 Specications ......................................................................................................

4

1.3 Mainboard Layout ...............................................................................................

5

1.3.1 Intel 945GC(V1.0) ........................................................................................................... 5

1.3.2 Intel 945GC(V2.0) ........................................................................................................... 6

1.4 Connecting Rear Panel I/O Devices

...................................................................

7

Chapter 2 Hardware Setup ..................................................................

8

2.1 Choosing a Computer Chassis .............................................................................

8

2.2 Installing Mainboard ...........................................................................................

8

2.3 Installation of the CPU and CPU Cooler...............................................................

9

2.3.1 Installation of the CPU ....................................................................................................

9

2.3.2 Installation of the CPU Cooler ....................................................................................... 10

2.4 Installation of Memory Modules........................................................................

10

2.5 Connecting Peripheral Devices..........................................................................

11

2.5.1 Floppy and IDE Disk Drive Connectors ............................................................................

11

2.5.2 Serial ATA Connectors .....................................................................................................

11

2.5.3 PCI and PCI Express slots ...............................................................................................

11

Chapter 3 Jumpers & Headers Setup ................................................

12

3.1 Checking Jumper Settings ................................................................................

12

3.2 CMOS Memory Clearing Header ........................................................................

12

3.3 Keyboard Power Function .................................................................................

12

3.4 FAN Power Connectors ...................................................................................... 13

3.5 Front Panel Switches & Indicators Headers .....................................................

13

3.6 Additional USB Port Headers ............................................................................

14

3.7 Front Panel Audio Connection Header...............................................................

14

3.8 Internal Audio Connectors ................................................................................

15

3.9 ATX Power InputConnectors ............................................................................. 15

Chapter 4 BIOS Setup Utility .............................................................

16

4.1 About BIOS Setup ..............................................

....................

.............................. 16

4.2 To Run BIOS Setup ............................................

....................

..............................

16

4.3 About CMOS..............................................

..........................................

..................... 16

4.4 The POST (Power On Self Test).......................................................................... 16

4.5 BIOS Setup — CMOS Setup Utility.....................................................................

17

4.5.1 CMOS Setup Utility ........................................................................................................

17

4.5.2 Control Keys ..................................................................................................................

18

4.5.3 Standard CMOS Features ..............................................................................................

19

4.5.4 Advanced BIOS Features ...............................................................................................

21

4.5.5 Advanced Chipset Features ...........................................................................................

24

4.5.6 Integrated Peripherals ..................................................................................................

26

4.5.7 Power Management Setup ............................................................................................

30

4.5.8 PnP PCI Conguration ................................................................................................... 32

4.5.9 PC Health Status ............................................................................................................ 33

4.5.10 Frequency/Voltage Control .........................................................................................

34

4.5.11 Load Fail-Safe Defaults ................................................................................................ 35

4.5.12 Load Optimized Defaults .............................................................................................. 35

4.5.13 Set Supervisor/User Password ....................................................................................

35

4.5.14 Save & Exit Setup .........................................................................................................

36

4.5.15 Exit Without Saving ......................................................................................................

36

Chapter 5 Driver Installation ...... .......................................................

37

- 3 -

Intel 945 Series User's Manual

Chapter 1 Introduction

1.1 Package Checklist

Thank you for choosing our product.

Please check the following packing and accessories, if there is any broken or part missing,

please contact with your franchiser.

• HDD Cable X 1

• Serial ATA Cable X 1

• Rear I/O Panel X 1

• User's Manual X 1

• Driver/Utility CD X 1

• FDD Cable X 1 (Optional)

• Serial ATA Power Cable X 1 (Optional)

The items listed above are for reference only, and are subject to change without notice.

- 4 -

Intel 945 Series User's Manual

1.2 Specications

CPU

- LGA775 socket for Intel

®

Core

TM

2 Duo/Pentium

®

D/Pentium

®

4/

Celeron

®

D Processors

- FSB 1333MHz/1066MHz(for Intel 945GC-A2 Chipset Only)

、

800MHz/

533MHz

- Hyper Threading Technology

Chipset

- Based on Intel 945GZ/945GC/945GC-A2 + ICH7

- ICH7: Intel FW82801GB

VGA - Intel Graphics Media Accelerator 950

Main Memory

- 2x 240-pin DIMM slots support (for Intel 945GC(V1.0) Only)

- 4x 240-pin DIMM slots support (for Intel 945GC(V2.0) Only)

- Maximum memory capacity up to 2GB

- Supports Dual Channel DDR2 667MHz(for Intel 945GC-A2 Chipset

Only)(Optional)

- Supports Dual Channel DDR2 533MHz

BIOS

- Supports Plug&Play

- Supports Advanced Power Management ACPI

- CPU temperature, Fan speed, System Voltage monitoring

Integrate Ports

- 1 X Floppy Drive, supports 360K/720K/1.2M/1.44M/2.88M oppy disk

- 8 X USB 2.0 ports, USB 1.1 is compliant

- 1 X COM port

- 1 X VGA port

- 1 X PS/2 Keyboard port

- 1 X PS/2 Mouse port

- 1 X RJ45 port

- 1 X LPT connector (Optional)

- 1 X eSATA port (Optional)

- Provides 1* IDE connector, 2* IDE devices could be connected,

support ATA 66/100

- Provides 4* SATA high speed HDD ports

Sound

- Onboard 6-channel/8-channel HD Audio Codec (Optional)

- Supports 16 bit Audio Codec

- Positioning Audio Support A3D, I3DL2

- Front Panel Jumper, provides stereo MIC port on front panel

Onboard LAN - Onboard 10/100/1000Mbps compatible LAN (Optional)

Expansion Slots

- 1 X PCI Express x16 slot (Intel 945GZ Chipset works at 4 X)

- 2 X PCI slots

- Support PCI Bus interface v2.2 compliant

Form Factor - Micro-ATX

- 5 -

Intel 945 Series User's Manual

1.3 Mainboard Layout

1.3.1 Intel 945GC(V1.0)

(This picture is only for reference)

- 6 -

Intel 945 Series User's Manual

1.3.2 Intel 945GC(V2.0)

(This picture is only for reference)

- 7 -

Intel 945 Series User's Manual

1.4 Connecting Rear Panel I/O Devices

The rear I/O part of this mainboard provides the following I/O ports:

• PS/2 Mouse: Connect to PS/2 mouse.

• PS/2 Keyboard: Connect to PS/2 keyboard.

• LPT: Connect to printer or other devices that support this communication protocol.

• COM: Connect to external modem, mouse or other devices that support this

communication protocol.

• VGA: Connect to monitor input.

• LAN: Connect to Local Area Network.

• USB: Connect to USB devices such as scanner, digital speakers, monitor, mouse, keyboard,

hub, digital camera, joystick etc.

• eSATA: Connect to peripherial SATA devices.The peripherial SATA devices must connect

inside SATA connectors. (Optional)

• AUDIO1:

Cen./Sub. (Center / Subwoofer): Connect to the center and subwoofer channel in the 7.1

channel audio system.

R.L./R.R. (Rear Left / Rear Right): Connect to the rear left and rear right channel in the 7.1

channel audio system.

S.L./S.R. (Surround Left / Surround Right): Connect to the surround left and surround right

channel in the 7.1 channel audio system.

Line-In: Connect to the line out from external audio sources.

Line-Out: Connect to the front left and front right channel in the 7.1-channel or regular

2-channel audio system.

Mic-In: Connect to the plug from external microphone.

- 8 -

Intel 945 Series User's Manual

Chapter 2 Hardware Setup

2.1 Choosing a Computer Chassis

• Choose a chassis big enough to install this mainboard.

• As some features for this mainboard are implemented by cabling connectors on the

mainboard to indicators and switches or buttons on the chassis, make sure your chassis

supports all the features required.

• If there is possibility of adopting some more hard drives, make sure your chassis has

sufcient power and space for them.

• Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O

shield of the chassis matches the I/O port conguration of this mainboard. You can nd

an I/O shield specically designed for this mainboard in its package.

2.2 Installing Mainboard

Most computer chassis have a base with many mounting holes to allow the mainboard to

be securely attached, and at the same time, prevent the system from short circuits. There

are two ways to attach the mainboard to the

chassis base: (1) with studs, or (2) with spacers.

Basically, the best way to attach the board is with

studs. Only if you are unable to do this should you

attach the board with spacers. Line up the holes on

the board with the mounting holes on the chassis.

If the holes line up and there are screw holes, you

can attach the board with studs. If the holes line

up and there are only slots, you can only attach with

spacers. Take the tip of the spacers and insert them

into the slots. After doing this to all the slots, you can slide the board into position aligned

with slots. After the board has been positioned, make sure everything is OK before putting

the chassis back on.

To install this mainboard:

1. Locate all the screw holes on the mainboard and the chassis base.

2. Place all the studs or spacers needed on the chassis base and have them tightened.

3. Face the mainboard’s I/O ports toward the chassis’s rear panel.

4. Line up all the mainboard’s screw holes with those studs or spacers on the chassis.

5. Install the mainboard with screws and have them tightened.

The mainboard and its component layouts illustrated in this chapter were

based mainly on model “Intel 945GC(V1.0)”, unless speci cally stated.

Always power off the computer and unplug the AC power cord before adding or removing

any peripheral or component. Failing to do so may cause severe damage to your

mainboard and/or peripherals. Plug in the AC power cord only after you have carefully

checked everything.

To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they are

already fastened on the chassis base and are without mounting-holes on the mainboard to

align with.

- 9 -

Intel 945 Series User's Manual

2.3 Installation of the CPU and CPU Cooler

Before installing the CPU, please comply with the following conditions:

1. Please make sure that the mainboard supports the CPU.

2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong

direction, the CPU will not insert properly. If this occurs, please change the insert direction

of the CPU.

3. Please add an even layer of heat sink paste between the CPU and CPU cooler.

4. Please make sure the CPU cooler is installed on the CPU prior to system use, otherwise

overheating and permanent damage of the CPU may occur.

5. Please set the CPU host frequency in accordance with the processor specications. It is not

recommended that the system bus frequency be set beyond hardware specications since

it does not meet the required standards for the peripherals. If you wish to set the frequen-

cy beyond the proper specications, please do so according to your hardware

specications including the CPU, graphics card, memory, hard drive, etc.

2.3.1 Installation of the CPU

1

2

5

6

7

8

9

10

1. Open the socket lever by

pushing the lever down and

away from the socket (see

Figure 1, 1 and 2).

2. Lift the load plate. Do not

touch the socket contacts

(see Figure 2, 3 and 4)

3 . Re m o v e t h e p l a s t i c

protective socket cover

from the load plate (see

Figure 3, 5). Do not discard

the protective socket cover.

Always replace the socket

cover if the processor is

removed from the socket.

4. Remove the processor

f r o m t h e p r o t e c t i v e

processor cover. Hold the

processor only at the edges,

being careful not to touch

the bottom of the processor

(see Fig u re 4). Do not

d i s c a r d t h e p r o t e c t i v e

processor cover. Always

r e p l a c e t h e p r o c e s s o r

back to the package if the

processor is removed from

the socket.

5. Hold the processor with

yo u r t h u m b a n d i n d e x

ngers oriented as shown in

Figure 5. Make sure ngers

align to the socket cutouts

(see Figure 5, 6). Align

notches (see Figure 5, 7)

with the socket see (Figure

5, 8). Lower the processor

straight down without tilting

or sliding the processor in

the socket.

6. Pressing down on the

load plate (Figure 6, 9)

c l o s e a n d e n g a g e t h e

socket lever (Figure 6, 10).

Figure 1

Figure 2

Figure 3

Figure 4

Figure 6

Figure 5

- 10 -

Intel 945 Series User's Manual

2.3.2 Installation of the CPU Cooler

For proper installation, please kindly refer to the instruction manuals of your CPU Cooler.

2.4 Installation of Memory Modules

This mainboard provides two 240-pin DDRII (Double Data Rate) DIMM slots (Intel945GC(V2.0)

provides 4x) , and supports Dual Channel Memory Technology. For dual channel

conguration, you always need to install two identical (the same brand, speed, size and chip-

type) memory modules in the DDRII DIMM slots to activate Dual Channel Memory

Technology. Otherwise, it will operate at single channel mode.

To install system memory:

1. Power off the computer and unplug the

AC power cord before installing or

removing memory modules.

2. Locate the DIMM slot on the board.

3. Hold two edges of the DIMM module

carefully, keep away from touching its

connectors.

4. Align the notch key on the module with

the rib on the slot.

5. Firmly press the module into the slots until the ejector tabs at both sides of the slot

automatically snap into the mounting notch. Do not force the DIMM module in with extra

force as the DIMM module only ts in one direction.

6. To remove the DIMM modules, push the two ejector tabs on the slot outward

simultaneously, and then pull out the DIMM module.

Dual-Channel Memory installation (For Intel 945GC(V2.0) Only)

The Intel 945GC(V2.0) includes 4 DIMM sockets, and each Channel has two DIMM sockets as

following:

Channel 1 : DIMM1, DIMM2

Channel 2 : DIMM3, DIMM4

The following is a Dual Channel Memory conguration table:

(D: Double Side, S: Single Side, "--": Empty)

Ejector Tab

Notch Key

Mounting Notch

Rib

Channel 1 Channel 2

Dual Channel

DIMM1 DIMM2 DIMM3 DIMM4

S -- S -- Enabled

S -- -- S Enabled

-- S S -- Enabled

-- S -- S Enabled

S S S S Enabled

D -- D -- Enabled

D -- -- D Enabled

-- D D -- Enabled

-- D -- D Enabled

Static electricity can damage the electronic components of the computer or optional

boards. Before starting these procedures, ensure that you are discharged of static

electricity by touching a grounded metal object briey.

- 11 -

Intel 945 Series User's Manual

2.5 Connecting Peripheral Devices

2.5.1 Floppy and IDE Disk Drive Connectors

The FDD connector connects up to two oppy drives with a 34-wire, 2-connector oppy

cable.Connect the single end at the longer length of ribbon cable to the FDD on the board,

the two connectors on the other end to the oppy disk drives connector. Generally you need

only one oppy disk drive in your system.

2.5.2 Serial ATA Connectors

Each SATA connector serves as one single channel to connect one SATA device by SATA

cable.

2.5.3 PCI and PCI Express slots

Install PCI Express X16 graphics card into slot “PCIE1”.

Install PCI card into slots “PCI1” or “PCI2”.

Each of the IDE port connects up to two

IDE drives at Ultra ATA/100 mode by one

40-pin, 80-conductor,and 3-connector Ultra

ATA/66 ribbon cables.

Connect the single end (blue connector)

at the longer length of ribbon cable to

the IDE port of this board, the other two

ends (gray and black connector) at the

shorter length of the ribbon cable to the

connectors of your hard drives.

Make sure to congure the “Master” and “Slave”

relation before connecting two drives by one

single ribbon cable. The red line on the ribbon

cable must be aligned with pin-1 on both the IDE

port and the hard-drive connector.

The red line on the ribbon cable must be aligned with pin-1 on both the FDD port and the oppy connector.

- 12 -

Intel 945 Series User's Manual

Chapter 3 Jumpers & Headers Setup

3.1 Checking Jumper Settings

• For a 2-pin jumper, plug the jumper cap on both

pins will make it CLOSE (SHORT). Remove the

jumper cap, or plug it on either pin (reserved for

future use) will leave it at OPEN position.

• For 3-pin jumper, pin 1~2 or pin 2~3 can be

shorted by plugging the jumper cap in.

How to identify the PIN1 jumpers?

Please check the mainboard carefully, the PIN1

is marked by "1" or white thick line.

3.2 CMOS Memory Clearing Header

The time to clear the CMOS memory occurs when (a)

the CMOS data becomes corrupted, (b) you forgot

the supervisor or user password preset in the BIOS

menu, (c) you are unable to boot-up the system

because the CPU ratio/clock was incorrectly set in the

BIOS menu, or (d) whenever there is modication on

the CPU or memory modules.

This header uses a jumper cap to clear the CMOS

memory and have it recongured to the default

values stored in BIOS.

• Pins 1 and 2 shorted

(Default): Normal

operation.

• Pins 2 and 3 shorted:

Clear CMOS memory.

To clear the CMOS memory and load in the default values:

1. Power off the system.

2. Set pin 2 and pin 3 shorted by the jumper cap. Wait for a few seconds. Set the jumper

cap back to its default settings --- pin 1 and pin 2 shorted.

3. Power on the system.

4. For incorrect CPU ratio/clock settings in the BIOS, press <Del> key to enter the BIOS

setup menu right after powering on system.

5. Set the CPU operating speed back to its default or an appropriate value.

6. Save and exit the BIOS setup menu.

3.3 Keyboard Power Function(JKB)

Pin 1-2 short: Disabled power on by keyboard

Pin 2-3 short: Support power on by keyboard

No rmal

(D efaul t)

Cl ear C M OS

JB AT or CL R CMOS1 _

1 2 3

Disabled

(Defau l t)

Enabled

1 2 3

JKB:

- 13 -

Intel 945 Series User's Manual

3.4 FAN Power Connectors

These connectors each provide power to the cooling fans installed in your system.

CFAN or CFAN1: CPU Fan Power Connector

SYSFAN1: System Fan Power Connector

SYSFAN2: System Fan Power Connector (Optional)

3.5 Front Panel Switches & Indicators Headers

HDD_LED (Hard Driver LED Header)

Connect the HDD LED cable to these PINs, in order to see the HDD status

RESET (Reset Control)

This connector connects to the case-mounted reset switch for rebooting your computer

without having to turn off your power switch. This is a preferred method of rebooting in

order to prolong the lift of the system’s power supply.

PWR-ON (Power Button)

This connector connects to the case-mounted power switch to power ON/OFF the system.

SPEAKER (Speaker)

This 4-pin connector connects to the case-mounted speaker. You should follow the instruction

of the speaker cable.

CFAN or CFAN1

SFAN1

SFAN2

These fan connectors are not jumpers. DO NOT place

jumper caps on these connectors.

- 14 -

Intel 945 Series User's Manual

3.6 Additional USB Port Headers

3.7 Front Panel Audio Connection Header

This header provides the connection to audio connector at front panel.

Pin Pin Assignment Pin Pin Assignment

1 VCC 2 VCC

3 Data 0- 4 Data 1-

5 Data 0+ 6 Data 1+

7 Ground 8 Ground

10 NC

HD Audio:

Pin No. Denition

1 MIC2_L

2 AGND

3 MIC2_R

4 NC

5 OUT_R

6 MIC2_JD

7 SENCE

8 No Pin

9 OUT_L

10 OUT_JD

AC'97 Audio:

Pin No. Denition

1 MIC

2 GND

3 MIC Power

4 NC

5 Line Out (R)

6 NC

7 NC

8 No Pin

9 Line Out (L)

10 NC

FUSB1 FUSB2,

1

2

9

10

F AUDIO_

1

2

9

10

- 15 -

Intel 945 Series User's Manual

3.8 Internal Audio Connectors

Connect CD-ROM or DVD-ROM audio out to the connector.

3.9 ATX Power Input Connectors

This mainboard provides two power connectors to connect power supplier.

CD IN_

1

Pin No. Denition

1 CD-L

2 GND

3 GND

4 CD-R

GND

+

12V

1

2

3

4

+ .

+

+ .

.

3 3V

12V

5VSB

PWR OK

COM

5V

COM

5V

COM

3 3V

+3 3V

COM

5V

COM

PS ON

COM

12V

3 3V

+

-

_

-

+ .

1

12

13

24

- 16 -

Intel 945 Series User's Manual

Chapter 4 BIOS Setup Utility

BIOS stands for Basic Input and Output System. It was once called ROM BIOS when it was

stored in a Read-Only Memory (ROM) chip

.

Now manufacturers would like to store BIOS in

EEPROM which means Electrically Erasable Programmable Memory. BIOS used in this series

of mainboard is stored in EEPROM, and is the first program to run when you turn on your

computer.

BIOS performs the following functions:

1. Initializing and testing hardware in your computer (a process called "POST", for Power On

Self Test).

2. Loading and running your operating system.

3. Helping your operating system and application programs manage your PC hardware by

means of a set of routines called BIOS Run-Time Service.

4.1 About BIOS Setup

BIOS Setup is an interactive BIOS program that you need to run when:

1. Changing the hardware of your system. (For example: installing a new Hard Disk etc.)

2. Modifying the behavior of your computer. (For example: changing the system time or date,

or turning special features on or off etc.)

3. Enhancing your computer's behavior. (For example: speeding up performance by turning

on shadowing or cache)

4.2 To Run BIOS Setup

First access BIOS setup menu by pressing <DEL> key after “POST” is complete (before OS is

loaded). BIOS will then display the following message:

4.3 About CMOS

CMOS is the memory maintained by a battery. CMOS is used to store the BIOS settings you

have selected in BIOS Setup. CMOS also maintains the internal clock. Every time you turn

on your computer, the BIOS looks into CMOS for the settings you have selected and

congures your computer accordingly. If the battery runs out of power, the CMOS data will

be lost and POST will issue a “CMOS invalid” or “CMOS checksum invalid” message. If this

happens, you have to replace the battery and check and congure the BIOS Setup for the

new start.

4.4 The POST (Power On Self Test)

POST is an acronym for Power On Self Test. This program will test all things the BIOS does

before the operating system is started. Each of POST routines is assigned a POST code, a

unique number which is sent to I/O port 080h before the routine is executed.

DEL: SETUP

- 17 -

Intel 945 Series User's Manual

Phoenix - AwardBIOS CMOS Setup Utility

►

Standard CMOS Features

►

Advanced BIOS Features

►

Advanced Chipset Features

►

Integrated Peripherals

►

Power Management Setup

►

PnP/PCI Configurations

►

PC Health Status

►

Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving

Esc : Quit

↑↓

→←

: Select Item

F10 : Save & Exit Setup

Time, Date, Hard Disk Type...

►

Standard CMOS Features

4.5 BIOS Setup — CMOS Setup Utility

4.5.1 CMOS Setup Utility

After powering up the system, the BIOS message appears on the screen, the memory count

begins, and then the following message appears on the screen:

If this message disappears before you respond, restart the system by pressing <Ctrl> +

<Alt>+ <Del> keys, or by pressing the Reset button on computer chassis. Only when these

two methods should be fail that you restart the system by powering it off and then back on.

After pressing <Del> key, the main menu screen appears.

Press DEL to enter SETUP

• Standard CMOS Features

This setup page includes all the items in standard compatible BIOS.

• Advanced BIOS Features

This setup page includes all the items of Award special enhanced features.

• Advanced Chipset Features

This setup page includes the Chipset features.

• Integrated Peripherals

This setup page includes all onboard peripherals.

• Power Management Setup

This setup page includes all the items of Green function features.

• PnP/PCI Congurations

This setup page includes all the congurations of PCI & PnP ISA resources.

•

In order to increase system stability and performance, our engineering staff is

constantly improving the BIOS menu. The BIOS setup screens and descriptions

illustrated in this manual are for your reference only, and may not completely

match with what you see on your screen.

•

Do not change the BIOS parameters unless you fully understand its function.

- 18 -

Intel 945 Series User's Manual

• PC Health Status

This setup page is the System auto detect temperature, voltage, fan, speed.

• Frequency/Voltage Control

This setup page is control CPU clock and frequency ratio.

• Load Fail-Safe Defaults

Fail-Safe Defaults indicates the value of the system parameters which the system would

be in safe conguration.

• Load Optimized Defaults

Optimized Defaults indicates the value of the system parameters which the system would

be in best performance conguration.

• Set Supervisor Password

Change, set, or disable password. It allows you to limit access to the system and Setup,

or just to Setup.

• Set User Password

Change, set, or disable password. It allows you to limit access to the system.

• Save & Exit Setup

Save CMOS value settings to CMOS and exit setup.

• Exit Without Saving

Abandon all CMOS value changes and exit setup.

4.5.2 Control Keys

Press F1 to pop up a small help window that describes the appropriate keys to use and the

possible selections for the highlighted item.

Please check the following table for the function description of each control key.

Control Key(s) Function Description

←

/

→

Move cursor left or right to select Screens

↑

/

↓

Move cursor up or down to select items

+/

-/PU/PD

To Change option for the selected items

<Enter>

To bring up the selected screen

<ESC>

Main Menu - Quit and not save changes into CMOS Status

Page Setup Menu and Option Page Setup Menu - Exit

current page and return to Main Menu

<F1>

General help

<F2>

Item Help

<F5>

Restore the previous CMOS value from CMOS, only for

Option Page Setup Menu

<F6>

Load the fail-safe default CMOS value from BIOS default

table

<F7>

Load the Optimized Defaults

<F10>

Save all the CMOS changes

- 19 -

Intel 945 Series User's Manual

4.5.3 Standard CMOS Features

・

Date (mm:dd:yy)

This item sets the date you specify (usually the current date) in the format of [Month],

[Date],and [Year].

・

Time (hh:mm:ss)

This item sets the time you specify (usually the current time) in the format of [Hour],

[Minute],and [Second].

►

IDE Channel 0 Master/Slave,SATA Channel 1~4

Click <Enter> key to enter its submenu:

Phoenix - AwardBIOS CMOS Setup Utility

IDE Channel 0 Master

IDE HDD Auto-Detection

IDE Channel 0 Master

Access Mode

Capacity

Cylinder

Head

Precomp

Landing Zone

Sector

[Press Enter]

[Auto]

80 GB

38309

16

0

38308

255

Item Help

Menu Level

►►

To auto-detect the

HDD

’

s size, head... on

this channel

↑↓

→←

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Press Enter

Phoenix - AwardBIOS CMOS Setup Utility

Standard CMOS Features

Date (mm:dd:yy)

Time (hh:mm:ss)

►

IDE Channel 0 Master

►

IDE Channel 0 Slave

►

SATA Channel 1

►

SATA Channel 3

►

SATA Channel 2

►

SATA Channel 4

Drive A

Drive B

Halt On

Base Memory

Extended Memory

Total Memory

Mon, Jun 11 2007

13 : 19 : 44

[MAXTOR STM380215A]

[None]

[1.44M, 3.5in.]

[None]

[All Errors]

640K

1047552K

1048576K

Item Help

Menu Level

►

Change the day, month,

year and century

↑↓

→←

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Jun

Page is loading ...

Intel 945GZ User manual

This manual is also suitable for

Intel 945GZ User manual

Related papers

Other documents