Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manuale d’uso
Manual del usuario
202
Copyright © 2003 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in
any form without the written permission of ROLAND CORPORATION.
201a
Before using this unit, carefully read the sections entitled:
“USING THE UNIT SAFELY” and “IMPORTANT NOTES” (p. 2;
p. 4). These sections provide important information
concerning the proper operation of the unit. Additionally, in
order to feel assured that you have gained a good grasp of
every feature provided by your new unit, Owner’s manual
should be read in its entirety. The manual should be saved
and kept on hand as a convenient reference.
M-10E
10 CHANNEL 5 STEREO MIXER
2
USING THE UNIT SAFELY
001
• Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
................................................................................................
002c
• Do not open (or modify in any way) the unit or its
AC adaptor.
................................................................................................
003
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct sunlight in
an enclosed vehicle, near a heating duct, on top of heat-
generating equipment); or are
• Damp (e.g., baths, washrooms, on wet floors); or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
................................................................................................
007
• Make sure you always have the unit placed so it is
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
008c
• Be sure to use only the AC adaptor supplied with
the unit. Also, make sure the line voltage at the
installation matches the input voltage specified on
the AC adaptor’s body. Other AC adaptors may
use a different polarity, or be designed for a
different voltage, so their use could result in
damage, malfunction, or electric shock.
................................................................................................
009
• Do not excessively twist or bend the power cord,
nor place heavy objects on it. Doing so can damage
the cord, producing severed elements and short
circuits. Damaged cords are fire and shock
hazards!
................................................................................................
010
• This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could cause
permanent hearing loss. Do not operate for a long
period of time at a high volume level, or at a level
that is uncomfortable. If you experience any
hearing loss or ringing in the ears, you should
immediately stop using the unit, and consult an
audiologist.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE:
BROWN:
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
NEUTRAL
LIVE
For the U.K.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
3
011
• Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
................................................................................................
012c
• Immediately turn the power off, remove the AC
adaptor from the outlet, and request servicing by
your retailer, the nearest Roland Service Center, or
an authorized Roland distributor, as listed on the
“Information” page when:
• The AC adaptor or the power-supply cord has been
damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been spilled onto
the unit; or
• The unit has been exposed to rain (or otherwise has
become wet); or
• The unit does not appear to operate normally or
exhibits a marked change in performance.
................................................................................................
013
• In households with small children, an adult should
provide supervision until the child is capable of
following all the rules essential for the safe
operation of the unit.
................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
................................................................................................
015
• Do not force the unit’s power-supply cord to share
an outlet with an unreasonable number of other
devices. Be especially careful when using extension
cords—the total power used by all devices you
have connected to the extension cord’s outlet must
never exceed the power rating (watts/amperes) for
the extension cord. Excessive loads can cause the
insulation on the cord to heat up and eventually
melt through.
................................................................................................
016
• Before using the unit in a foreign country, consult
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
................................................................................................
019
• Batteries must never be recharged, heated, taken
apart, or thrown into fire or water.
101b
• The unit and the AC adaptor should be located so
their location or position does not interfere with
their proper ventilation.
................................................................................................
102d
• Always grasp only the output plug or the body of
the AC adaptor when plugging into, or
unplugging from, this unit or an outlet.
................................................................................................
103b
• Any accumulation of dust between the AC adaptor
and the power outlet can result in poor insulation
and lead to fire. Periodically wipe away such dust
with a dry cloth. Also, disconnect the power plug
from the power outlet whenever the unit is to
remain unused for an extended period of time.
................................................................................................
104
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
................................................................................................
106
• Never climb on top of, nor place heavy objects on
the unit.
................................................................................................
107d
• Never handle the AC adaptor body, or its output
plugs, with wet hands when plugging into, or
unplugging from, an outlet or this unit.
................................................................................................
108b
• Before moving the unit, disconnect the AC adaptor
and all cords coming from external devices.
................................................................................................
109b
• Before cleaning the unit, turn off the power and
unplug the AC adaptor from the outlet.
................................................................................................
110b
• Whenever you suspect the possibility of lightning
in your area, disconnect the AC adaptor from the
outlet.
................................................................................................
111: Selection
• If used improperly, batteries may explode or leak
and cause damage or injury. In the interest of
safety, please read and observe the following
precautions (p. 21).
3
• Remove the batteries whenever the unit is to remain
unused for an extended period of time.
5
• If a battery has leaked, use a soft piece of cloth or paper
towel to wipe all remnants of the discharge from the
battery compartment. Then install new batteries. To
avoid inflammation of the skin, make sure that none of
the battery discharge gets onto your hands or skin.
Exercise the utmost caution so that none of the
discharge gets near your eyes. Immediately rinse the
affected area with running water if any of the discharge
has entered the eyes.
6
• Never keep batteries together with metallic objects
such as ballpoint pens, necklaces, hairpins, etc.
................................................................................................
112
• Used batteries must be disposed of in compliance
with whatever regulations for their safe disposal
that may be observed in the region in which you
live.
4
IMPORTANT NOTES
291a
In addition to the items listed under “USING THE UNIT SAFELY” on pages 2 and 3, please read and observe
the following:
Power Supply: Use of
Batteries
301
• Do not use this unit on the same power circuit with any
device that will generate line noise (such as an electric
motor or variable lighting system).
302
• The AC adaptor will begin to generate heat after long
hours of consecutive use. This is normal, and is not a
cause for concern.
304a
• When installing or replacing batteries, always turn off the
power on this unit and disconnect any other devices you
may have connected. This way, you can prevent
malfunction and/or damage to speakers or other devices.
307
• Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions
and/or damage to speakers or other devices.
Placement
351
• Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum.
To alleviate the problem, change the orientation of this
unit; or move it farther away from the source of inter-
ference.
352b
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the vicinity of
this unit. Such noise could occur when receiving or initi-
ating a call, or while conversing. Should you experience
such problems, you should relocate such wireless devices
so they are at a greater distance from this unit, or switch
them off.
354a
• Do not expose the unit to direct sunlight, place it near
devices that radiate heat, leave it inside an enclosed
vehicle, or otherwise subject it to temperature extremes.
Excessive heat can deform or discolor the unit.
355b
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit. Damage
or malfunction may result if you attempt to use the unit in
this condition. Therefore, before using the unit, you must
allow it to stand for several hours, until the condensation
has completely evaporated.
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry cloth
or one that has been slightly dampened with water. To
remove stubborn dirt, use a cloth impregnated with a
mild, non-abrasive detergent. Afterwards, be sure to wipe
the unit thoroughly with a soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or
deformation.
Additional Precautions
553
• Use a reasonable amount of care when using the unit’s
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
556
• When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s
internal elements.
558a
• To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about
those around you (especially when it is late at night).
559a
• When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise,
you will need to use equivalent packaging materials.
562
• Use a cable from Roland to make the connection. If using
some other make of connection cable, please note the
following precautions.
• Some connection cables contain resistors. Do not use cables that
incorporate resistors for connecting to this unit. The use of such
cables can cause the sound level to be extremely low, or impos-
sible to hear. For information on cable specifications, contact
the manufacturer of the cable.
5
FEATURES
The M-10E is a 10-channel (5 stereo) mixer that features the following functionality.
Designed for the multimedia age, it allows sound from peripherals such as a MIDI sound module
or CD player to be mixed for the ideal playback balance. A maximum of five channels (four stereo
channels + AUX) of stereo sound can be controlled.
In applications such as video editing, it can be used to edit audio by mixing narration,
simultaneous recording, background music, and sound effects.
10 in/2 out Configuration
Five stereo channels (10 in’s) and 2
outputs (stereo) are provided.
Dual Power Supply
Conveniently powered using either
dry-cell batteries on the market (6F22,
S-006P/9V), or an AC adaptor.
Microphone Setup
Since it is equipped with SENS
(sensitivity) knobs, the M-10E can
accommodate a broad variety of
signals, from microphone to line
level.
Overload Indicators
The L/R OVERLOAD LEDs allow
you to set the best signal level for
optimum audio performance.
AUX OUT Jacks
Connection to a recording device
(cassette, DAT or open reel deck, for
example) can be made through these
jacks.
PHONES Jack
Stereo headphones can be connected
to this jack for convenient mix
monitoring.
ACCESSORIES
The M-10E package contains the following items.
Before you begin using the mixer, please check that these items are all present.
fig.8e
• AC ADAPTOR BOSS PSA Series
• Owner’s Manual
M-10E
AC Adaptor
Owner's Manual
6
PANEL DESCRIPTIONS
fig.1+2e
8. MASTER Volume Slider
15. AUX IN Jacks13. AC Adaptor Jack
16. INPUT (1/4-inch Phone) Jacks14. AUX OUT Jacks
12. INPUT (RCA Phono) Jacks10. POWER Switch 11. OUTPUT Jacks
4. POWER Indicator2. OVERLOAD L/R Indicators
3. AUX IN Knob 5. PHONES Knob
9. PHONES Jack6. SENS Knobs 7. CHANNEL VOLUME Sliders
1. BALANCE Knobs
7
PANEL DESCRIPTIONS
1. BALANCE Knobs
These knobs adjust the stereo input balance for each
channel. At the center position, the left and right signals
are at the same level. Rotating the knob clockwise or
counterclockwise will shift the sound field to the right or
left respectively.
2. OVERLOAD L/R Indicators
These indicators light when the mixed signal level is too
high. If these LEDs light frequently, lower the input
sensitivity by rotating the SENS knob of each channel
counterclockwise.
* These indicators are not affected by the position of the
MASTER volume slider.
* These indicators light at 6 dB below the clipping level (the
point at which distortion becomes audible).
3. AUX IN Knob
Adjusts the input level of the device connected to the AUX
IN (Auxiliary Input) jacks.
* The AUX IN knob controls the L/R input signals
simultaneously.
4. POWER Indicator
Lights when the M-10E is turned on.
* If you are using a battery and the POWER indicator does
not light (or lights dimly), replace the battery.
5. PHONES Knob
Controls the headphone volume.
* The headphone volume is not affected by the position of the
MASTER Volume slider.
6. SENS Knobs
Adjust the input sensitivity for each channel. They are
used to optimize the signal level to avoid distortion.
Rotating a SENS knob clockwise will increase the
sensitivity (increase the volume), while rotating it
counterclockwise will decrease the sensitivity (decrease
the volume). When a microphone is connected to one of
the 1/4 inch phone jacks, be sure to rotate the
corresponding SENS knob completely clockwise (to the “-
50 dB” position).
* Each SENS knob controls the L/R signals in each channel
simultaneously.
7. Channel VOLUME Sliders
These sliders provide volume control for each channel. Set
these sliders relative to one another to achieve the best
audio mix. (The marked position (“0”) of each channel
indicates the optimum level.)
* Each VOLUME slider controls the L/R signals in each
channel simultaneously.
8. MASTER Volume Slider
Adjusts the overall output of the M-10E.
* The MASTER slider does not affect the output level of the
AUX OUT jacks or the PHONES jack.
9. PHONES Jack (Stereo Mini Type)
Connect stereo headphones to this jack.
10. POWER Switch
Switches the unit on and off.
11. OUTPUT Jacks
(RCA Phono Jacks/
1/4“ Phone Jacks)
These jacks provide output of the final mixed signals.
They can be connected to a PA system, or to the inputs on
another mixer.
12. Input Jacks (RCA Phono Jacks)
Devices (computer music or audio equipment, for
example) with RCA phono plugs should be connected to
these inputs. (To connect a monaural device, use both the
L/R inputs (when possible), or use one of the standard 1/
4 inch phone jacks.)
13. AC Adaptor Jack
Connect an AC adaptor (PSA Series) to this jack. (Be sure
to use the adaptor specified for your country.)
* When an AC adaptor is connected, the batteries in the unit
are not used.
* If you are not going to use the unit on batteries for a long
period of time, remove them from the unit.
14. AUX OUT Jacks (RCA Phono Jacks)
These jacks are convenient for recording direct to a DAT,
cassette, or open reel deck (for example).
(Convenient further still because the output level is not
affected by the MASTER Volume slider.)
15. AUX IN Jacks (RCA Phono Jacks)
These input jacks are ideal for connecting devices that do
not require L/R balance adjustment (audio equipment, for
example).
16. Input Jacks (1/4“ Phone Jacks)
Devices (electronic instruments or mics, for example) with
1/4 inch phone plugs should be connected to these inputs.
If you are connecting a monaural device such as a
microphone, connect it to L (MONO).
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
16
CONNECTIONS
921
* To prevent malfunction and/or damage to speakers or other devices, always turn down the
volume, and turn off the power on all devices before making any connections.
Connecting Headphones
Connect the headphones to the PHONES jack.
fig.5ae
Headphones
17
CONNECTIONS
Example connections for editing audio for video
Here is an example of video post-recording in which you mix sounds from a
variety of audio devices.
fig.5be
* Use a monaural mic, and connect the mic to channel 1 (MIC) or 3 (MIC).
* “Post recording” refers to the process of recording audio material such as music, sound effects, and
narration for a previously-recorded video.
923
* If there are batteries (6F22, S-006P/9V) in the unit while an AC adaptor is being used, normal operation
will continue should the line voltage be interrupted (power blackout or power cord disconnection).
983
* Howling could be produced depending on the location of microphones relative to speakers. This can be
remedied by:
1. Changing the orientation of the microphone(s).
2. Relocating the microphone(s) at a greater distance from speakers.
3. Lowering volume levels.
Microphone
AC Adaptor
(BOSS PSA Series)
CD Player
Video Cassette Recorder
IN
OUT
IN
R
L
R
L
R
L
R
L
Camcorder
IN
MD Player
Images
IN
18
CONNECTIONS
Example connections for mixing or switching between
desktop media production sources or electronic
musical instruments
fig.5e
* Use a monaural mic, and connect the mic to channel 1 (MIC) or 3 (MIC).
* If you are using the M-10E as a sub-mixer for another mixer, connect the MASTER OUTPUT L, R
jacks to the input jacks of the other mixer.
* “Desktop media production” (DTMP) is a new way of enjoying music and visual material using your
computer. A “sound module” is an electronic sound generating device that you connect to your
computer in order to enjoy DTMP.
IN
R
L
IN
R
L
OUT
L
IN
R
L
IN
R
L
IN
R
L
OUT
R
L
OUT
R
(BOSS PSA Series)
Monitor Speakers
Sound Module
Sound Module
CD Player
Cassette Deck
Mixer
AC Adaptor
Keyboard
Microphone
19
OPERATION
941
* Once the connections have been completed (p. 16), turn on power to your various
devices in the order specified. By turning on devices in the wrong order, you risk
causing malfunction and/or damage to speakers and other devices.
1. Switch off the M-10E and all the units to be connected.
2. Make all the necessary connections. Set the BALANCE knob of each channel to
the center position and the SENS knob of each channel to the “+4” position. Set
each Channel VOLUME slider to “0” (the marked position) and the MASTER
Volume slider to the “-∞” position.
943
* Always make sure to have the MASTER volume level turned down before
switching on power. Even with the volume all the way down, you may still hear
some sound when the power is switched on, but this is normal, and does not
indicate a malfunction.
fig.6
3. Switch on all the units connected to the M-10E.
4. Switch on the M-10E.
944a
* When operating on battery power only, the unit’s indicator will become dim when
battery power gets too low. Replace the battery as soon as possible.
5. Slowly raise the MASTER Volume slider to an appropriate level.
20
OPERATION
6. Use the SENS knobs to adjust input sensitivity for each channel.
* For minimum noise and/or distortion, set the levels so the OVERLOAD indicators
light only briefly on input peaks.
fig.9e
7. Adjust the L/R input balance of each channel using the BALANCE knobs.
8. Adjust the channel levels relative to one another using the Channel VOLUME
sliders.
9. Set the overall output volume using the MASTER slider.
* Use a monaural mic, and connect the mic to channel 1
(MIC) or 3 (MIC).
On the channel to which the mic is connected, turn the
sensitivity knob all the way to the right.
21
BATTERY REPLACEMENT
This mixer is designed to be used with the included AC adapter, but you can also operate it on
battery power by installing a commercially available battery (6F22, S-006P/9V). Here’s how to
change the battery.
928
* When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under the
four corners or at both ends to prevent damage to the buttons and controls. Also, you should try to orient
the unit so no buttons or controls get damaged.
929
* When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over.
1. Remove the cover from the battery case located on the bottom of the unit.
fig.3
2. Remove the old battery and replace it with new one.
fig.4
3. Replace the cover.
If used improperly, batteries may explode or leak and cause damage or injury. In the interest of
safety, please read and observe the following precautions.
* Remove the batteries whenever the unit is to remain unused for an extended period of time.
* If a battery has leaked, use a soft piece of cloth or paper towel to wipe all remnants of the discharge from the
battery compartment. Then install new batteries. To avoid inflammation of the skin, make sure that none of
the battery discharge gets onto your hands or skin. Exercise the utmost caution so that none of the discharge
gets near your eyes. Immediately rinse the affected area with running water if any of the discharge has
entered the eyes.
* Never keep batteries together with metallic objects such as ballpoint pens, necklaces, hairpins, etc.
22
TROUBLESHOOTING
Q: The volume level of the instrument connected to INPUT, AUX IN, MASTER
OUTPUT, and AUX OUT is too low.
A: Could you be using a connection cable that contains a resistor?
Use a connection cable that does not contain a resistor.
23
SPECIFICATIONS
M-10E: 10 CHANNEL 5 STEREO MIXER
Frequency Response
10 Hz to 50 kHz +1/-3 dB (at minimum gain)
Nominal Input Level
INPUT (1 to 4) -50 dBu to +4 dBu
INPUT (5 to 8) -20 dBu to +4 dBu
AUX IN -10 dBu
Input Impedance
INPUT (1 to 4) 20 kΩ (Stereo)/10 kΩ (Mono)
INPUT (5 to 8) 20 kΩ (Stereo)
AUX IN 20 kΩ to 120 kΩ (Stereo)
Nominal Output Level
OUTPUT 0 dBu
AUX OUT -10 dBu
Output Impedance
OUTPUT 1 kΩ
AUX OUT 1 kΩ
Recommended Load Impedance
OUTPUT 10 kΩ or greater
AUX OUT 10 kΩ or greater
HEADPHONE 30 Ω or greater
Headphones Output
0.1 mW (33 Ω load)
Total Harmonic Distortion
0.05% or less
(minimum gain, 10 Hz to 50 kHz at nominal output)
Equivalent Input Noise
-107 dBu (input terminated with 150 Ω, IHF-A, Typ.)
Controls
BALANCE Knob x 4
SENS Knob x 4
Channel Volume Slider x 4
AUX IN Knob x 1
Headphones Knob x 1
Master Volume Slider x 1
Power Switch
Indicators
Power Indicator
Overload Indicator (L/R)
Connectors
<Front>
Headphone Jack (Stereo mini type)
<Rear>
Input (L/R) x 4 (RCA phono type)
Input (L(MONO)/R) x 2 (1/4-inch phone type)
Output (L/R) x 1 (RCA phono type)
Output (L/R) x 1 (1/4-inch phone type)
AUX IN (L/R) x 1 (RCA phono type)
AUX OUT (L/R) x 1 (RCA phono type)
AC Adaptor Jack (DC 9V)
Power Supply
DC 9V: Dry Battery
(6F22, S-006P/9V Commercially available)
AC Adaptor
Current Draw
45 mA (at maximum)
961
* Expected battery life under continuous use:
Carbon: approx. 3 hours
Alkaline: approx. 7 hours
(These figures will vary depending on the actual conditions of use.)
Dimensions
218 (W) x 170 (D) x 60 (H) mm
8-5/8 (W) x 6-3/4 (D) x 2-3/8 (H) inches
Weight
750 g (including battery)
1 lb 11 oz
Accessories
Owner’s Manual
AC Adaptor BOSS PSA Series
Options
Dry Battery (6F22, S-006P/9V Commercially available)
*0 dBu = 0.775 Vrms
962a
* In the interest of product development, the specifications and/or
appearance of this unit are subject to change without prior
notice.
03239167 1RTC
Information
When you need repair service, call your nearest EDIROL/Roland Service Center or authorized EDIROL/Roland distributor
in your country as shown below.
U. S. A. / CANADA
EDIROL Corporation North
America
425 Sequoia Drive, Suite 114
Bellingham, WA 98226
U. S. A.
TEL: (360) 594-4276
FAX: (360) 594-4271
http://www.edirol.com/
EUROPE
EDIROL (Europe) Ltd.
Studio 3.4 114 Power Road
London W4 5PY
U. K.
TEL: +44 (0)20 8747 5949
FAX:+44 (0)20 8747 5948
http://www.edirol.com/europe
Deutschland
TEL: 0700 33 47 65 20
France
TEL: 0810 000 371
Italia
TEL: 02 93778329
As of April 1, 2003 (EDIROL-1)
EGYPT
Al Fanny Trading Office
9, EBN Hagar A1 Askalany Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: 20-2-417-1828
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
That Other Music Shop
(PTY) Ltd.
11 Melle St., Braamfontein,
Johannesbourg, SOUTH AFRICA
P.O.Box 32918, Braamfontein 2017
Johannesbourg, SOUTH AFRICA
TEL: (011) 403 4105
Paul Bothner (PTY) Ltd.
17 Werdmuller Centre,
Main Road, Claremont 7708
SOUTH AFRICA
P.O.BOX 23032, Claremont 7735,
SOUTH AFRICA
TEL: (021) 674 4030
AFRICAAFRICA
HONG KONG
Tom Lee Music Co., Ltd.
Service Division
22-32 Pun Shan Street, Tsuen
Wan, New Territories,
HONG KONG
TEL: 2415 0911
ASIA
INDIA
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra Mahalaxmi
Flats Compound Off. Dr. Edwin
Moses Road, Mumbai-400011,
INDIA
TEL: (022) 2493 9051
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
INDONESIA
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
MALAYSIA
BENTLEY MUSIC SDN BHD
140 & 142, Jalan Bukit Bintang
55100 Kuala Lumpur,MALAYSIA
TEL: (03) 2144-3333
PHILIPPINES
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
KOREA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
SINGAPORE
CRISTOFORI MUSIC PTE
LTD
Blk 3014, Bedok Industrial Park E,
#02-2148, SINGAPORE 489980
TEL: 6243-9555
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung Shan
N.Road Sec.2, Taipei, TAIWAN,
R.O.C.
TEL: (02) 2561 3339
THAILAND
Theera Music Co. , Ltd.
330 Verng NakornKasem, Soi 2,
Bangkok 10100, THAILAND
TEL: (02) 2248821
VIETNAM
Saigon Music
138 Tran Quang Khai St.,
District 1
Ho Chi Minh City
VIETNAM
TEL: (08) 844-4068
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
BRAZIL
Roland Brasil Ltda
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
NEW ZEALAND
Roland Corporation Ltd.
32 Shaddock Street, Mount Eden,
Auckland, NEW ZEALAND
TEL: (09) 3098 715
AUSTRALIA/
NEW ZEALAND
CENTRAL/LATIN
AMERICA
MEXICO
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico D.F.
MEXICO
TEL: (55) 5668-6699
VENEZUELA
Musicland Digital C.A.
Av. Francisco de Miranda,
Centro Parque de Cristal, Nivel
C2 Local 20 Caracas
VENEZUELA
TEL: (212) 285-8586
URUGUAY
Todo Musica S.A.
Francisco Acuna de Figueroa 1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
DENMARK
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: 3916 6200
FRANCE
Roland France SA
4, Rue Paul Henri SPAAK,
Parc de l'Esplanade, F 77 462 St.
Thibault, Lagny Cedex FRANCE
TEL: 01 600 73 500
FINLAND
Roland Scandinavia As,
Filial Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt,
GERMANY
TEL: (040) 52 60090
HUNGARY
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint, HUNGARY
TEL: (23) 511011
AUSTRIA
Roland Austria GES.M.B.H.
Siemensstrasse 4, P.O. Box 74,
A-6063 RUM, AUSTRIA
TEL: (0512) 26 44 260
BELGIUM/HOLLAND/
LUXEMBOURG
Roland Benelux N. V
.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
EUROPE
GREECE
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
IRELAND
Roland Ireland
Audio House, Belmont Court,
Donnybrook, Dublin 4.
Republic of IRELAND
TEL: (01) 2603501
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
NORWAY
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: 2273 0074
PORTUGAL
Tecnologias Musica e Audio,
Roland Portugal, S.A.
Cais Das Pedras, 8/9-1 Dto
4050-465 PORTO
PORTUGAL
TEL: (022) 608 00 60
POLAND
P. P. H. Brzostowicz
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
RUSSIA
MuTek
3-Bogatyrskaya Str. 1.k.l
107 564 Moscow, RUSSIA
TEL: (095) 169 5043
SPAIN
Roland Electronics
de España, S. A.
Calle Bolivia 239, 08020
Barcelona, SPAIN
TEL: (93) 308 1000
SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
SWEDEN
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
UKRAINE
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo, UKRAINE
TEL: (03131) 414-40
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 702701
ROMANIA
FBS LINES
Piata Libertatii 1,
RO-4200 Gheorgheni
TEL: (066) 164-609
BAHRAIN
Moon Stores
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
TEL: 211 005
ISRAEL
Halilit P. Greenspoon &
Sons Ltd.
8 Retzif Ha’aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
JORDAN
AMMAN Trading Agency
245 Prince Mohammad St.,
Amman 1118, JORDAN
TEL: (06) 464-1200
KUWAIT
Easa Husain Al Yousifi Est.
Abdullah Salem Street,
Safat, KUWAIT
TEL: 243-6399
LEBANON
Chahine S.A.L.
Gerge Zeidan St., Chahine Bldg.,
Achrafieh, P.O.Box: 16-5857
Beirut, LEBANON
TEL: (01) 20-1441
CYPRUS
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia,
CYPRUS
TEL: (022) 66-9426
IRAN
MOCO, INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
TEL: (021) 285-4169
MIDDLE EAST
QATAR
Badie Studio & Stores
P.O. Box 62,
Doha, QATAR
TEL: 423554
SAUDI ARABIA
aDawliah Universal
Electronics APL
Corniche Road, Aldossary Bldg.,
1st Floor, Alkhobar,
SAUDI ARABIA
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
TURKEY
Barkat Muzik aletleri ithalat
ve ihracat Ltd Sti
Siraselviler Caddesi Siraselviler
Pasaji No:74/20
Taksim - Istanbul, TURKEY
TEL: (0212) 2499324
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai, U.A.E.
TEL: (04) 3360715
SYRIA
Technical Light & Sound
Center
Khaled Ebn Al Walid St.
Bldg. No. 47, P.O.BOX 13520,
Damascus, SYRIA
TEL: (011) 223-5384
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 Anhuaxili
Chaoyang District, Beijing,
CHINA
TEL: (010) 6426-5050
AUSTRALIA
Roland Corporation
Australia Pty., Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
TEL: (02) 9982 8266
This product complies with the requirements of European Directive 89/336/EEC.
For EU Countries
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
