Sharp LC-M3700 User manual

Printed in Japan

Gedruckt in Japan

Imprimé au Japon

Impreso en Japón

TINS-A842WJZZ

03P07-JKK

SHARP CORPORATION

Printed on 100% post-consumer recycled paper.

Gedruckt auf 100% wiederverwertungs Papier.

Imprimé sur 100% de papier recyclé.

Impreso en 100% de papel reciclado de postconsumo.

INPUT

RETURN

MENU

STANDBY/ON

ENLARGE

WIDE

LCD MONITOR

ENTER

VOL

LC-M3700

LC-M3710

OPERATION MANUAL

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

MANUAL DE MANEJO

WIDE LCD MONITOR

BREITBILD-LCD-MONITOR

MONITEUR GRAND ÉCRAN À

CRISTAUX LIQUIDES

MONITOR LCD PANORÁMICO

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

OPERATION MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUAL DE MANEJO

LC-M3700/LC-M3710

Cover.p65 03.7.25, 1:24 PM1

1

US

LC-M3700

LC-M3710

WIDE LCD MONITOR

ENGLISH

OPERATION MANUAL

ENGLISH

IMPORTANT INFORMATION

CAUTION

RISK OF ELECTRIC

SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT

REMOVE COVER.

NO USER-SERVICEABLE PARTS

INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of

uninsulated “dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within a triangle is

intended to alert the user to the presence

of important operating and maintenance

(servicing) instructions in the literature

accompanying the product.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS PRODUCT TO RAIN OR MOISTURE.

IMPORTANT:

To aid reporting in case of loss or theft, please

record the product’s model and serial numbers in

the space provided. The numbers are located in

the rear of the product.

Model No.:

Serial No.:

U.S.A. ONLY

US

2

INFORMATION:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Relocate or adjust the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: FCC Regulations state that any unauthorized changes or modifications to this

equipment not expressly approved by the manufacturer could void the user’s authority

to operate this equipment.

CAUTION: Use the supplied AC cord as it is.

Do not remove the core part from the AC cord, and do not change the way of

winding cables around the core part.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according

to the manufacturer’s instructions.

U.S.A. ONLY

IMPORTANT INFORMATION (Continued)

3

US

Introduction

Connection

and Installation

Basic Operation

PC Operation

Settings and

Adjustments

Troubleshooting and

Specifications

Appendix

Thank you for your purchase of a SHARP LCD product. To ensure safety and many

years of trouble-free operation of your product, please read the Safety Precautions

carefully before using this product.

SAFETY PRECAUTIONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage

if improperly handled. This product has been engineered and manufactured with the highest priority on safety.

However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please

observe the following instructions when installing, operating and cleaning the product. To ensure your safety

and prolong the service life of your LCD product, please read the following precautions carefully before using

the product.

1. Read instructions—All operating instructions must be read and understood before the product is oper-

ated.

2. Keep this manual in a safe place—These safety and operating instructions must be kept in a safe place

for future reference.

3. Observe warnings—All warnings on the product and in the instructions must be observed closely.

4. Follow instructions—All operating instructions must be followed.

5. Cleaning—Unplug the power cord from the AC outlet before cleaning the product. Use a damp cloth to

clean the product. Do not use liquid cleaners or aerosol cleaners.

6. Attachments—Do not use attachments not recommended by the manufacturer. Use of inadequate attach-

ments can result in accidents.

7. Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink and

laundry tub, swimming pool and in a wet basement.

8. Stand—Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an

unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to

the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold

with the product. When mounting the product on a wall, be sure to follow the manufacturer’s instructions.

Use only the mounting hardware recommended by the manufacturer.

9. When relocating the product placed on a cart, it must be moved with utmost care.

Sudden stops, excessive force and uneven floor surface can cause the product to fall

from the cart.

10. Ventilation—The vents and other openings in the cabinet are designed for ventilation.

Do not cover or block these vents and openings since insufficient ventilation can cause

overheating and/or shorten the life of the product. Do not place the product on a bed,

sofa, rug or other similar surface, since they can block ventilation openings. Do not

place the product in an enclosed place such as a bookcase or rack, unless proper

ventilation is provided or the manufacturer’s instructions are followed.

11. Power cord protection—The power cords must be routed properly to prevent people from stepping on

them or objects from resting on them.

12. The LCD panel used in this product is made of glass. Therefore, it can break when the product is

dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD

panel breaks.

13. Overloading—Do not overload AC outlets or extension cords. Overloading can cause fire or electric

shock.

14. Entering of objects and liquids—Never insert an object into the product through vents or openings. High

voltage flows in the product, and inserting an object can cause electric shock and/or short internal parts.

For the same reason, do not spill water or liquid on the product.

15. Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high

voltage and other dangerous conditions. Request a qualified service person to perform servicing.

DEAR SHARP CUSTOMER

US

4

16. Repair—If any of the following conditions occurs, unplug the power cord from the AC outlet, and request

a qualified service person to perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid was spilled on the product or when objects have fallen into the product.

c. When the product has been exposed to rain or water.

d. When the product does not operate properly as described in the operating instructions.

Do not touch the controls other than those described in the operating instructions. Improper adjust-

ment of controls not described in the instructions can cause damage, which often requires extensive

adjustment work by a qualified technician.

e. When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates

that the product needs servicing.

17. Replacement parts—In case the product needs replacement parts, make sure that the service person

uses replacement parts specified by the manufacturer, or those with the same characteristics and per-

formance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other

danger.

18. Safety checks—Upon completion of service or repair work, request the service technician to perform

safety checks to ensure that the product is in proper operating condition.

19. Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product

according to the method recommended by the manufacturer.

20. Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves and other

heat-generating products (including amplifiers).

21. Power source—This product must operate on a power source specified on the specification label. If you

are not sure of the type of power supply used in your home, consult your dealer or local power company.

For units designed to operate on batteries or another power source, refer to the operating instructions.

The LCD panel is a very high technology product with 3,147,264 thin film transistors, giving you fine picture

details.

Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red.

Please note that this does not affect the performance of your product.

WARNING:

This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

WARNING:

To reduce the risk of fire or electric shock, do not expose this product to rain or

moisture.

SAFETY PRECAUTIONS (Continued)

5

US

Introduction

Page

Dear SHARP Customer........................................................................... 3

Safety Precautions.................................................................................. 3

Introduction ............................................................................................. 5

Features ................................................................................................. 6

Part Names – Display ............................................................................ 8

Removing the terminal cover ................................................................. 9

Part Names – Remote Control Unit ..................................................... 10

Removing the battery cover ................................................................. 11

Supplied Accessories ........................................................................... 12

Connection and Installation ................................................................. 13

Connecting Peripheral Equipment ....................................................... 13

Connecting external speakers ............................................................. 18

Connecting the AC cord ....................................................................... 19

Connecting multiple monitors ............................................................... 20

Mounting options .................................................................................. 23

Bundling cables .................................................................................... 29

Basic Operation .................................................................................... 30

Turning on Power ................................................................................. 30

Main POWER switch ............................................................................ 30

STANDBY/ON ...................................................................................... 30

Remote Control Unit............................................................................. 31

Menu Items .......................................................................................... 32

Menu option selection .......................................................................... 32

Menu screen explanation ..................................................................... 33

PC (analog) input mode menu items ................................................... 34

AV input mode menu items .................................................................. 35

Language setting .................................................................................. 36

PC Operation ......................................................................................... 37

PC connection ...................................................................................... 37

Communication conditions ................................................................... 37

Communication procedure ................................................................... 38

RS-232C command table ..................................................................... 46

Settings and Adjustments.................................................................... 51

Picture .................................................................................................. 51

Audio .................................................................................................... 53

Power control ....................................................................................... 53

Setup .................................................................................................... 54

Option ................................................................................................... 57

Detailed explanation............................................................................. 58

Troubleshooting and Specifications ................................................... 65

Troubleshooting ................................................................................... 65

Specifications ....................................................................................... 67

Optional Accessories ........................................................................... 67

Appendix ................................................................................................ 68

Appendix 1: PC Compatibility Chart ..........................................................

68

Appendix 2: Dimensional Drawings ...........................................................

69

Appendix 3: Menu Option Reference Chart ...............................................

70

CONTENTS

US

6

Features

HIGH-DEFINITION (HD) PANEL

•

A large, flat LCD display panel with 3.15 million pixels lets you enjoy a detailed, high-

definition picture from a digital TV or a PC.

ASV

*

LOW-REFLECTION BLACK TFT LCD PANEL

•

SHARP’s unique ASV* low-reflection BLACK TFT LCD panel provides higher luminance,

higher contrast, and a wider viewing angle. This reduces reflection in the monitor when it

is placed near a window, and ensures brighter, more vivid image reproduction. With a

wide viewing angle of 170 degrees, both horizontally and vertically, the image is

beautiful, even when viewed off axis.

* ASV … Advanced Super View

CABINET DESIGN ENABLES VERTICAL AND HORIZONTAL

INSTALLATION

•

When mounted vertically, this monitor requires images coded for a vertical screen. It

does not have image rotation capability.

EQUIPPED WITH A VARIETY OF TERMINALS

•

INPUT1 Terminals are provided for two types of video input signal. Input Select

Video Input (BNC-terminal) NTSC (3.58/4.43)/PAL/SECAM (*1)

S-video Input (S-terminal) NTSC (3.58/4.43)/PAL/SECAM (*1)

•

INPUT2 This terminal can be set for input or output. INPUT2 Select

Video Input (RCA-terminal) NTSC (3.58/4.43)/PAL/SECAM (*1)

•

INPUT3 This terminal enables selection of the video signal type. Input Select

COMPONENT/RGB Input (BNC-terminal)

COMPONENT 480i/480p/576i/576p/1080i/720p (*2)

RGB Conforms to PC analog input. Appendix 1 (*2, *3)

•

PC

Analog Input (D-Sub terminal)

VGA/SVGA/XGA/SXGA and others

Appendix 1 (*2, *3)

Digital Input (DVI terminal)

VGA/SVGA/XGA/SXGA and others

Appendix 1

*1: There is a setting for auto-detection of the color system. (This is set to “Auto” at factory shipment.)

*2: Frequency is auto-detected.

*3: The INPUT3 (RGB) and PC (analog) inputs are compatible with Sync On Green input. PC (analog) input is

compatible with Csync input.

COMPATIBLE WITH VARIOUS COLOR SYSTEMS

•

Compatible with NTSC (3.58/4.43), PAL (50/60) and SECAM.

Numbers within refer to the main page(s) where the topic is explained.

9

54

56

54

68

57

13

7

US

Introduction

ENLARGEMENT FUNCTION

•

Allows output of enlarged images for 4- or 9-screen (“2×2” or “3×3”) setups, without using

a special-purpose external device.

CHAIN CONNECTION OF MULTIPLE MONITORS

•

Enables chain connection of monitors using video signal output (composite-video/D-Sub)

terminals.

•

Enables individual control via PC of multiple sets connected in a daisy chain using RS-

232C cables.

EXTERNAL CONTROL AND STATUS MONITORING FROM

A PC

•

The monitor can be controlled in various ways from a PC.

•

Multiple monitors can be individually controlled by connecting them in a daisy chain.

EXTERNAL SPEAKERS CAN BE CONNECTED

•

Compatible speakers: L/R, 8 ohm, 10W or larger

EQUIPPED WITH BUILT-IN MONITOR SPEAKER (MONO)

•

When activated from the menu screen, you can check the audio input status using the

built-in monitor speaker (mono).

CONTROL LOCK FUNCTIONS

•

The monitor is equipped with various operation lock functions to prevent unintended

operation or mischief. (The PIN can be set by the user.)

Numbers within refer to the main page(s) where the topic is explained.

56

20

22

37

18

57

54

61

37

58

Features (Continued)

Fluorescent Tubes

■ The fluorescent tubes in this product have a limited lifetime.

» If the screen gets dark, flashes, or does not turn on, change the fluorescent tubes with new

exclusive ones.

Expected lifetime: ............... 60,000 hours for LC-M3700 (horizontal mount)*

40,000 hours for LC-M3710 (vertical mount)*

*When “Brightness” is set to a center value.

» For more information, please contact your product dealer.

■ Because of the property of fluorescent tubes, the screen may flash during the initial period of use. If

this happens, please turn off the main power switch on the back of the monitor and turn on again to

confirm operation.

US

8

Part Names – Display

MENU

ENTER

UP

RIGHT

LEFT

DOWN

INPUT

VOL

Numbers within refer to the main page(s) where the topic is explained.

Liquid Crystal Display panel

Side control panel

(See below.)

Front view

Side control panel

Remote

control sensor

*

When using the

remote control, point

it towards here.

STANDBY/ON

button

STANDBY/ON

indicator

Panel side

30

11

30

MENU

ENTER

VOL +/–

UP

LEFT

RIGHT

DOWN

INPUT

32

31

Menu operation

buttons

Cursor

control

LC-3700 LC-3710

About LC-M3710:

»

The SHARP logo for the LC-M3710 model is

on the vertical base.

9

US

Introduction

Removing the terminal cover

1. Hold down the two claws at the top of the terminal

cover, and pull the cover toward you so it opens a

little.

2. Slowly lift the cover so the three claws at the bottom

come loose from the claw holes in the console.

2 1

3

Rear view

Built-in monitor

speaker

57

SPEAKER (R)

External speaker terminal

(right)

18

POWER····················

Main power on/off

switch

30

SPEAKER (L)

External speaker terminal

(left)

18

AC Input

terminal···············

19

INPUT2 (INPUT/

OUTPUT)

14

VIDEO OUTPUT

17

RS-232C INPUT··············

17

RS-232C OUTPUT········

17

15

INPUT1

13

17

PC (DIGITAL) INPUT

16

INPUT3/PC (ANALOG)

OUTPUT············

INPUT3

PC (ANALOG)

INPUT··················

16

Removing the terminal cover

Lower claw

Upper claw

Part Names – Display (Continued)

US

10

Part Names – Remote Control Unit

INPUT

RETURN

MENU

STANDBY/ON

ENLARGE

WIDE

LCD MONITOR

ENTER

VOL

Numbers within refer to the main page(s) where the topic is explained.

Signal transmitter

Remote control unit

STANDBY/ON

MENU····································

VOL +/– ··································

30

ENLARGE

31

INPUT

31

RETURN

32

WIDE·····································

31

Cursor control ('/"/\/|)············

32

ENTER··································

32

31

11

US

Introduction

Removing the battery cover

Cautions regarding remote control unit

» Do not expose the remote control unit to shock. In addition, do not

expose the remote control unit to liquids, and do not place it in an

area with high humidity.

» The remote control unit may not work properly if the remote control

sensor is under direct sunlight or strong lighting.

In such cases, change the angle of the lighting or the monitor, or

operate the remote control unit closer to the remote control sensor.

Cautions regarding batteries

Improper use of batteries can result in chemical leakage

or explosion. Be sure to follow the instructions below.

» Do not mix old and new batteries, or batteries of different

types.

» Do not charge or disassemble batteries.

» Place batteries with their terminals corresponding to the

± and — as indicated in the compartment.

» Do not short-circuit the batteries.

Caution

NOTE:

» The batteries supplied with this product may

have a shorter life expectancy due to storage

conditions. Replace with new batteries at the

earliest opportunity.

» If you will not use the remote control for a long

time, remove its batteries.

» If the remote control does not work, even with

new batteries, take the batteries out, check

whether they are facing the right way, then

replace them.

Remote control operation range

If the remote control unit does not work well:

» Objects between the remote control unit and the remote

control sensor may prevent proper operation.

» Replace the batteries when they run low as this may shorten

the remote control operation range.

10°

6 m

7 m

6 m

Remote

control sensor

Gently hold down and

press in the arrow

direction.

Part Names – Remote Control Unit (Continued)

US

12

Make sure the following accessories are provided

with the product.

Remote control unit (× 1)

INPUT

RETURN

MENU

STANDBY/ON

ENLARGE

WIDE

LCD MONITOR

ENTER

VOL

“AA” size battery (× 2)

Pages 11, 30 - 32 Page 11

AC cord, 9 ft.10-

1

/8″(3 m) (× 1)

Cable clamp (× 1)

Screw (× 1)

Cable binder (× 3)

Page 19

Page 29

Supplied Accessories

Terminal cover mounting screw (× 2)

Flat washer (× 2)

Caution:

» This monitor is equipped with a temporary stand when shipped from the factory. Please note this stand is for temporary use

only until the monitor is properly mounted. Be sure to use a special-purpose AN-37ST1 table stand or AN-37AG1 wall-

mount bracket (both optional). Mounting Options.

23

Page 29

(RRMCGA186WJSA)

» Operation manual × 1

(UBATU0013TAZZ)

(QACCDA024WJPZ)

(XTBS940P-16000)

(LHLDW1118CEZZ)

(LHLDWA017WJKA)

(XBBS960P20000)

(XWHS960-16180)

13

US

Introduction

Connection

and Installation

INPUT1

■ INPUT1: Terminals are provided for two types of video input signal. Input Select

No matter which video signal is selected, the system uses the signal input to the audio terminals for

audio.

Related topic:

Input Select

*1 “Auto” (automatic color system detection) is factory preset value.

Color System

54

57

INPUT 1

AUDIO

VIDEOS-VIDEO

R - - L

1

S-video

INPUT1

audio

Video

Connecting Peripheral Equipment

Terminal type

BNC

S terminal

Compatible signals

NTSC (3.58/4.43), PAL, SECAM (*1)

Video

S-video

US

14

Connecting Peripheral Equipment (Continued)

INPUT2

INPUT 2 (INPUT/OUTPUT)

VIDEO

AUDIOR - - L

2

INPUT2

audio

Video

Terminal type

RCA

Compatible signals

NTSC (3.58/4.43), PAL, SECAM (*2)Video

■ INPUT2: Input or output can be selected for INPUT2. (*1) INPUT2 Select

This setting cannot be switched when INPUT2 is currently being displayed.

When this is set to “Output”, video signals input from the INPUT1 video input terminal are output. (*3)

An audio signal is output with this setting (i.e. the audio signal corresponding to the video currently

being displayed). (*4)

Related topic:

INPUT2 Select

*1 “Input” is factory preset value.

*2 “Auto” (automatic color system detection) is factory preset value.

Color System

*3 Outputs video from INPUT1, regardless of the currently displayed signal.

*4 If the “INPUT2 Select” is set to “Output”, audio output is as follows.

56

57

Example 1

Input Selection

: INPUT1

“Input Select”

: AV

Example 2

Input Selection

: INPUT3

“Input Select”

: RGB

31

54

31

54

INPUT2 video output: Video from INPUT1

INPUT2 audio output: Audio from INPUT1

INPUT2 video output: Video from INPUT1

INPUT2 audio output: Audio from INPUT3

15

US

Connection

and Installation

INPUT3

INPUT 3

AUDIOPr/Cr/RPb/Cb/B VDHDY/G

3

Input Select: RGB

INPUT3 audio

Input Select:

COMPONENT

Horizontal

sync signal (H sync)

Vertical

sync signal (V sync)

The signal is input with the Y/Pb/Pr (Y/Cb/Cr) terminals. The HD and VD terminals are

not used. Video adjustment options on the menu are the AV type.

Compatible input range: 480i/576i, 480p/576p, 1080i (50Hz (*4) /60Hz), 720p (60Hz). (*1)

The monitor operates using Video (RGB) and Sync (HD/VD) signals, just like a PC

(analog). Supported sync signals are ordinary separate sync (HD/VD) and Sync On

Green. (*2) (*3)

Video adjustment options on the menu are the PC type.

Compatible input range: Conforms to PC (analog). Appendix 1

COMPONENT

RGB

68

■ INPUT3: Either COMPONENT or RGB can be selected for the input video signal. Input Select

Related topic:

Input Select

*1 Auto-detects video signal frequency.

*2 Automatic sync signal type detection

*3 Sync signal presence is detected in the order: Separate Sync → Sync On Green. If for some reason

Separate Sync is not input, the system will operate assuming that the signal is a Sync On Green

signal (i.e. that the sync signal is contained in the G signal of RGB), and this may result in an

unstable image, depending on the video signal.

*4 1080i (50Hz) corresponds to a SMPTE274M signal. (Horizontal frequency is 28.125kHz)

54

Connecting Peripheral Equipment (Continued)

US

16

PC

Terminal type

D-Sub15-pin

DVI-D

Compatible signals

VGA, SVGA, XGA, SXGA and others Appendix 1

In addition to ordinary Separate Sync (HD/VD) signals, the system is also

compatible with Composite Sync (Csync) and Sync On Green. (*1) (*2)

VGA, SVGA, XGA, SXGA and others Appendix 1

Analog

Digital

68

Connecting Peripheral Equipment (Continued)

■ PC: Terminals for two kinds of PC video input signal are available. Input Select

No matter which video signal is selected, the system uses the signal input to the audio terminals for

audio.

Related topic:

*1 Auto-detects Sync signal type.

*2 Sync signal presence is detected in the order: Separate Sync → Composite Sync → Sync On

Green. If for some reason neither Separate Sync nor Composite Sync is input, the system will

operate assuming that the signal is a Sync On Green signal (i.e. that the sync signal is contained in

the G signal of RGB), and this may result in an unstable image, depending on the video signal.

54

PC(DIGITAL)INPUT

PC (digital) video

PC(ANALOG)INPUT

AUDIO

PC (analog) video

PC audio

17

US

Connection

and Installation

VIDEO OUTPUT

■ When INPUT2 is displayed, video from INPUT2 is output. Otherwise video from INPUT1 is output.

INPUT3/PC (ANALOG) OUTPUT

■ When INPUT3 is displayed, video from INPUT3 is output. Otherwise PC (analog) video is output.

RS-232C INPUT/RS-232C OUTPUT

■ The RS-232C INPUT and RS-232C OUTPUT are used to control this monitor with a PC.

To connect a single monitor to a PC, connect to the RS-232C INPUT terminal.

To connect multiple monitors in a daisy chain for control by PC, use the RS-232C OUTPUT terminal.

37

RS-232C INPUT

RS-232C OUTPUT

INPUT 3 / PC (ANALOG) OUTPUT

VIDEO

OUTPUT

Video

Connecting Peripheral Equipment (Continued)

US

18

Connecting External Speakers

Make sure to connect the speaker jack and cable polarity

(±, —)

properly.

■ The speaker jacks have plus ± and minus — polarity. Plus is red and minus is black.

The cables are also divided into plus and minus.

When connecting the left/right speakers, be sure to connect the plus/minus jacks with the correct

cables.

» You can output audio from the built-in monitor speaker on the back of the monitor. See “Monitor Speaker Output”

on page 57 for details.

Speaker compatibility:

» Be sure to use external speakers with an

impedance of 8 ohm and a rated input of

at least 10W.

"Rear view

"SPEAKER L

terminal

"SPEAKER R

terminal

How to connect the speaker

cables

Pull up the lid.

1

Insert the edge

of the cable.

2

Put the lid back

down.

3

To external speaker

(left)

To external

speaker (right)

NOTE:

19

US

Connection

and Installation

Connecting the AC Cord

Caution

Be sure to turn the main POWER off when connecting the cord.

» When connecting the power cord to the main unit, always

use the cable clamp to keep the power cord from coming

loose.

Fastening the AC cord

1. Plug the AC cord into the AC input terminal on the back

of the monitor.

» Align the shape of the plug and the connector, and

insert all the way in.

2. Attach the supplied cable clamp to the AC cord.

3. Align the hole of the cable clamp with the screw hole on

the monitor, and fasten the cable clamp screw.

4. Plug the AC cord into the AC power outlet.

» Be sure to plug all the way into the socket.

NOTE:

Screw

Cable clamp

Attaching portion

"Rear view

Plug (to power outlet)

Plug (to the AC

input terminal)

AC cord 9 ft. 10-

1

/

8

″ (3 m)

Power outlet

'AC input terminal

(plug in here)

Page is loading ...

Sharp LC-M3700 User manual

This manual is also suitable for

Sharp LC-M3700 User manual

Related papers

Other documents