Installation Guide

AT-VTP-800

1

Velocity 8” Touch Panel

AT-VTP-800

1 x AT-VTP-800

1 x Metal mounting plate

4 x Mounting screws

1 x Wall installation template

1 x 2-gang mud ring

1 x Installation Guide

Package Contents

IMPORTANT: Velocity Gateway (AT-VGW-250) must be set up before the AT-VTP-800 is

fully functional.

The Atlona AT-VTP-800-BL and AT-VTP-800-WH are 8” touch panels in black and white,

respectively, for the Atlona Velocity™ Control System. They feature contemporary, rened styling

for modern presentation environments with 1280x800 native resolution, and a capacitive glass

surface that supports multi-touch and gesture interactions. These touch panels conveniently

install into a wall or furniture via a US two-gang opening. Also available is the optional AT-VTP-

TMK tabletop mounting kit for placement on a meeting table or lectern. The VTP-800-BL and

VTP-800-WH feature Power over Ethernet (PoE), enabling a single network connection for data

and power. Setting up the touch panels is eortless as the AV control GUI is automatically

Installation Guide

AT-VTP-800

2

the unit.

2 Install the back box (not included) or mud ring (included) into the wall.

3 Screw the included metal mounting plate into the mud ring using the 4 included screws.

4 Remove the two screws from the bottom of the touch panel.

5 Run the Ethernet cable through the mud ring and metal mounting plate.

6 Connect the Ethernet and/or power cable into the back of the touch panel.

7 Line up the touch panel with the mounting plate and thread the metal hooks into the four

holes on the back of the panel.

8 Gently press the touch panel down to ensure it is fully seated on the mounting plate.

9 Replace the two bottom screws to secure the touch panel to the metal mounting plate.

Installation Guide

AT-VTP-800

3

3 Plug the Ethernet cable into the back of the touch panel.

4 Place the touch panel on the stand, pushing the excess cable back through the stand at the

same time as resting the back panel of the touch panel in the rectangular front hole of the

stand.

5 Secure the touch panel to the stand using the four stand screws (included in the stand box).

a Thread the screws through the 4 pre-drilled holes in the front of the stand into the four

screw holes on the back of the touch panel.

NOTE: Tight the screws by hand. To avoid damage to the touch panel, do not

overtighten.

Installation and Set Up

NOTE: Installation of the Velocity Touch Panel can only be done after the VGW-250

has been set up. View the AT-VGW-250 Installation Guide and Velocity Manual for

instructions.

Installation Guide

AT-VTP-800

4

4 When the unit displays the IP information, press CONTINUE.

a If the touch panel does not display an IP, select the Set Static IP slider.

b Assign the unit a static IP. Ensure there are no other devices on the network with the

same IP to avoid connection issues.

5. The unit will load a new screen. Change the Device Alias (if needed) to help dierentiate

when there are multiple touch panels at a site.

7 The touch panel will scan for new gateways. Once the correct gateway is found, press USE.

Installation Guide

AT-VTP-800

5

8 On a network computer, use a browser to log into Velocity.

13 Depending on the room options there may be multiple buttons on the home page. Select the

any icon to open the room’s control page.

14 Select sources and displays by tapping on them.

a To route sources to displays, drag and drop the source icon onto the display box.

Installation Guide

AT-VTP-800

6

TUV WXYZ

1 2 3

4 5 6

7 8

0

2 Select Advanced Setup.

3 Type in the PIN. Default PIN is 554361.

Factory Reset - Press the Factory Reset button to clear all the settings and start the touch

pad set up again. Press the OK button to verify.

Advanced Settings

Once th touch pad has been set up, the settings can be changed or reset only through the

advanced settings.

1 To access the settings, swipe from the left side of the touch pad to the right.

Installation Guide

AT-VTP-800

7

Troubleshooting

Problem Cause Solution

My touchpad won’t power

on.

The touchpad is not

connected to a PoE switch.

• Connect the touchpad to a

switch that supports 802.3at

an IP.

not DHCP enabled.

to the right and press

the refresh button. It can

sometimes take up to 60

seconds to obtain an IP.

• Set the touchpad to static IP

by selecting the Set Static

IP slider and providing IP,

subnet, gateway, and DNS

server information.

Connection Diagram



Voltage

Sensor

Installation Guide

AT-VTP-800

8

© 2016 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered trademarks