Arrow Storage Products AK100 Owner's manual

Brand: Arrow Storage Products

Model: AK100

Type: Owner's manual

This manual is also suitable for

68383

PARTS LIST

ANCHOR KIT #AK100

INTRODUCTION

This anchor kit is intended for use on all Arrow storage buildings.

TOOLS AND MATERIALS REQUIRED

● Carpenter's Level ● 1/4" Masonary Drill Bit(Supplied)

● Drill (Electric) ● #2 Phillips Head Screwdriver

● Safety Glasses ● Tape Measure

● 1/8" (3,2 mm) Drill Bit ● 3/8" Wrench

● 1/4" (6,4 mm) Drill Bit ● Hammer

● Work gloves & long sleeves

ASSEMBLY INSTRUCTIONS:

Read the instructions and study the illustrations carefully. Follow

the step by step instructions to properly Anchor your Storage

Building.

RETAIN THIS MANUAL AND PARTS LIST AFTER

ASSEMBLY FOR FUTURE REFERENCE.

CHECK THE CONTENTS:

Check the contents of carton against the Parts List. Identify parts

to those shown in the illustrations. This will help you become

familiar with the parts on sight.

SAFETY RULES:

● ●

● Make sure no one is in path while drilling.

● Wear safety glasses, work gloves and long sleeves

while drilling.

ANCHORING THE STORAGE BUILDING TO A

CONCRETE PATIO OR SLAB

This concrete Anchor Kit comes complete with masonary drill bit,

fasteners and easy to follow instructions. For proper installation,

it is important that the overall size of the patio/slab has approxi-

mately 9/16" (1,4 cm) clearance between frame and edge of

concrete around entire perimeter.

IMPORTANT: Make sure Floor Frame is level and square

before proceeding with the anchoring.

One Anchor Kit is recommended for most buildings. Anchors are

used at each corner and spaced evenly along the Floor Frame.

NOTE: The following must be considered before starting to drill

concrete for installation of Hold Down Clips:

1. If your building has Floor Frame Splices.

A. Assemble and position Floor Frame.

B. Mark and drill hole location as described above.

This kit contains four Gussets to anchor the Floor Frame corners.

If your building is supplied with Gussets (some models have them),

disregard the ones supplied with the building.

Key # Part # Description (Quan.)

1 8397 Corner Gusset (4)

2 8398 Hold Down Clip (11)

Anchor Bolt (16)

3 66159 #10 x 1/2" (13 mm) Screw (39)

Masonary Drill Bit-1/4" (1)

1 2 3 Hardware Kit

ENTRANCE

Limits of

Floor Frame

Slab To Extend 9/16" (1,4 cm)

Beyond Floor Frame

Anchor Bolt Location

Equally Spaced Along Floor Frame

Floor Frame Assembly

of Storage Building

It is important that the entire

floor frame be anchored after

the building is erected.

Anchor Bolt

Corner Gusset

704960311

STEP 1

Corner Gusset Installation

1. Position Gussets into corners of Floor Frame with

flanged edges "UP".

2. Attach Gussets through aligning holes, or drill 1/8"

(3,2 mm) holes.

3. Through hole in center of Gusset, drill 1/4" (6,4 mm)

diameter hole in concrete using the Masonary Drill Bit

supplied.

IMPORTANT: Holes drilled in concrete must be at right

angle to surface and 2" (5,1 cm) deep. Use drill bit

furnished. Holes must not be more than 1/32" (0,1 cm)

over size or anchor bolts will not hold.

4. Place Anchoring Bolt in hole drilled and tap head

with hammer to set into place. Tighten nut with wrench.

STEP 2

Hold Down Clip Installation

1. Position Clips on Floor Frame (by panel rib) at equally

spaced intervals and attach using screws through

existing holes or drill 1/8" (3,2 mm) holes.

See Figure 1, 2 or 3.

2. NOTE: If other size Floor Frames (Figure 2) are to be

anchored, you must bend Hold Down Clips "UP" before

attaching to Floor Frame. (Figure 3) is for buildings

12'x10' (3,7 m x 3,0 m) through 14'x31' (4,3 m x 9,4 m) with

channel style floor frames. Additional kits may be

required.

3. Drill holes in concrete and anchor Clips to concrete in

same manner as described in Step 1.

STEP 3

Front Frame Anchor Installation

1. Drill 1/4" (6,4 mm) hole at center of Front Floor Frame

as shown. Switch to Masonary Bit supplied and continue

drilling to a 2" (5,1 cm) depth.

2. Anchor Frame to concrete with an Anchoring Bolt in

the same manner as described in Step 1.

For replacement parts or any questions concerning your

anchor kit, include the model no. of your kit and contact:

Arrow Shed, LLC

Customer Service Department

1101 North 4th Street

Breese, Illinois 62230

1-800-851-1085

[email protected]

Anchor Bolt

Drill 1/8" (3,2 mm) diameter hole

Corner Gusset

Slab/Patio

9/16" (1,4 cm)

(All Around)

FIGURE 3

Drill 1/8" (3,2 mm)

diameter hole

Anchor Bolt

Floor Frame

FIGURE 2

Ref. All Other Sizes

FIGURE 1

Hold Down Clip

Wall Panel Rib

Ref. Size 25/32" (2,0 cm)

Drill 1/8"

(3,2 mm)

diameter hole

Anchor Bolt

Hold Down Clip

Front Floor Frame

with Ramp

Floor Frame

Floor

Frame

Arrow Storage Products AK100 Owner's manual

Brand: Arrow Storage Products

Model: AK100

Type: Owner's manual

This manual is also suitable for

68383

Download PDF

report

Arrow Storage Products AK100 Owner's manual

This manual is also suitable for

Arrow Storage Products AK100 Owner's manual

Related papers

Other documents