Amazon Basics K001387 User manual

AmazonBasics Desk Monitor Mount

B00MIBN16O

2

English . . . . . . . . . . . . . . . . . . . . . .3

Français . . . . . . . . . . . . . . . . . . . .17

Deutsch . . . . . . . . . . . . . . . . . . . .31

日本語 . . . . . . . . . . 45

中文. . . . . . . . . . . . . . . . . . . . 59

Italiano . . . . . . . . . . . . . . . . . . . . .72

Español. . . . . . . . . . . . . . . . . . . . .86

3

English

Instruction Manual · English

AmazonBasics Desk Monitor Mount

Contents

Make sure that the package contains the following parts:

Upper arm

(1 pc)

Bracket cover

(1 pc)

Grommet bracket

(1 pc)

M8 (1/4-20UNC, 3 inch)

(1 pc)

Wing nut

(1 pc)

Cable tie

(2 pcs)

M4 × 10 mm screw

(4 pcs)

Lower arm

(1 pc)

M4 × 10 mm knob

(4 pcs)

Base

(1 pc)

4 mm Allen wrench

(1 pc)

2.5 mm Allen wrench

(1 pc)

M3 x 6 mm

screw

1 (pc)

4

Supported monitor weights

Your monitor mount supports a monitor of the following weight:

Monitor adjustments

Your monitor mount lets you adjust the monitor viewing angle, height, tilt, and orientation

(portrait or landscape).

5 to 25 lbs

(2.3 to 11.3 kg)

lbs

kg

360°

180°

360°

13 in.

(330 mm)

70°

5°

Viewing angle Height Tilt Orientation

5

Assembly Instructions

Step 1: Choose a mounting option.

You can mount the monitor arm using the:

• Desk-clamp mount to attach your monitor arm to the edge of a tabletop. Go to

“Desk-clamp mount” on page 6.

• Plate mount to attach your monitor mount to an area that is away from the edge of a

tabletop. This mounting option requires a hole through the mounting surface. Go to

“Plate mount” on page 7.

Caution: Because mounting surface materials

can vary widely, make sure that the mounting

surface is strong enough to handle your monitor

mount and the monitor.

6

Desk-clamp mount

Step A: Determine the thickness of the mounting surface, then use the 4 mm Allen wrench to

adjust the location of the mounting clamp assembly, if necessary.

•The top screw holes on the clamp bracket fit a mounting surface thickness of less than

5/8 in. (1.6 cm).

•The middle screw holes on the clamp bracket fit a mounting surface thickness between

1/4 to 1 5/8 in. (0.6 to 4.1 cm).

•The bottom screw holes on the clamp bracket fit a mounting surface thickness between

1 1/4 to 2 5/8 in (3.2 to 6.7 cm).

Step B: Slide the mounting clamp assembly onto the mounting surface, then tighten the

clamp.

Caution: Do not rotate the monitor past the

edge of desk. The weight of the monitor may

cause the desk to tip over.

<3/8 in. (1 cm)

1/2 to 1-3/8 in.

(1.2 to 3.56 cm)

1.5 to 2-3/8 in.

(3.7 to 6.0 cm)

4 mm Allen wrench

7

Plate mount

Step A: Remove the mounting clamp assembly from the clamp bracket on the base.

Step B: Remove the clamp bracket from the base. Keep the screws you remove. You will use

them later.

Step C: Make sure that the side of the grommet bracket with recessed screw holes is facing

down. Insert the M8 × 3 in. screw through the square hole in the center of the grommet

bracket.

Note: To keep the 3-inch screw from falling inside the base, temporarily attach the wing nut to

hold it in place.

4 mm

8

Step D: Attach the grommet bracket to the base with the 3 screws you removed from the

clamp bracket.

Note: If the screws are not flush to the grommet bracket, the grommet bracket is upside down.

Remove these screws and the M8 × 3 in. screw, turn the grommet bracket over, then put all the

screws back in.

Step E: Remove the clamp plate from the clamp assembly using a Phillips screwdriver.

Step F: Center the base over the top of the hole in the mounting surface, then, from the

bottom of the mounting surface, slide the clamp plate you removed onto the M8 × 3 in. screw.

Secure the clamp plate to the screw with the wing nut.

Note: The M8 × 3 in. screw must be centered in the hole.

Caution: For secure arm attachment and to

avoid equipment damage, the base and the

clamp plate must make contact with the

mounting surface on both sides of the hole.

4 mm

0.31 to 2 in.

(8 to 51 mm)

< 2.25 in.

(57 mm)

9

Step 2: Determine the orientation of the monitor

You can mount the monitor in a locked portrait or landscape orientation, or you can leave the

monitor free to rotate 360°.

• If you want the monitor to rotate freely, do not insert the M3 x 6 mm screw.

• If you want the monitor in a locked orientation, insert the M3 x 6 mm screw into the front

of the plate on the upper arm.

Note: If you insert the screw, then want to change the monitor’s orientation after you mount the

monitor to the upper arm, you need to remove the monitor from the upper arm and insert or

remove the M3 x 6 mm screw.

Monitor rotates freely.

Monitor is locked in portrait or

landscape orienation.

10

Step 3: Attach the upper arm to the back of the monitor using a Phillips screwdriver.

Note: If a stand is attached to the monitor, remove the stand.

Note: You can use the M4 × 10 mm screws or M4 × 10 mm knobs to attach the arm to the

monitor.

Caution: The mounting screw holes on the

back of the monitor may require screws of a

different type or length than the provided

M4 × 10 mm screws or knobs.

• Using screws of that are too big in

diameter will damage the screw holes on

the monitor.

• Using screws that are too small or too

short may cause the monitor to fall off the

arm.

• Using screws that are too long may

damage the interior of the monitor.

Before you attach the monitor to the upper arm,

make sure that the provided screws or knobs fit

the screw holes on the back of the monitor.

If the provided screws or knobs do not fit, refer

to the documentation that came with the

monitor for the correct screw type and size.

Warning: The upper arm is under

tension and will move up rapidly, on its

own, as soon as the attached monitor is

removed. For this reason, remove the upper

arm, lay the monitor face down on a soft

surface, then remove the monitor. Failure to

follow this instruction may result in serious

personal injury or equipment damage.

M4 × 10 mm screws M4 × 10 mm knobsOR

11

Step 4: Slide the lower arm onto the base. Slide the upper arm over the lower arm, then insert

the bracket cover into the top of the upper arm. The cover should snap into place.

Note: To remove the bracket cover, use a flathead screwdriver to pry off the cover.

Note: If the monitor is too high or too low, remove the upper and lower arms. Loosen the screw

on the base ring with the 2.5 mm wrench, slide the ring up or down, then tighten the screw.

Bracket

cover

12

Step 5: Insert the cable ties through the loops on the bottom of the upper arm, route the

monitor cables along the upper arm, then loosely secure the cables to the upper arm with the

cable ties. Do not over-tighten the ties. If the ties are too tight and you try to remove them, you

may damage the monitor cables.

Squeeze the tabs on the lower arm cover to remove the cover, route the monitor cables along

the bottom of the lower arm, then replace the covers.

Caution: Before you tighten the cable ties,

adjust your monitor to the highest position. This

will leave enough slack in the cables for monitor

movement/height adjustment.

L

o

w

e

r

a

r

m

c

o

v

e

r

C

a

b

l

e

t

i

e

s

13

Step 6: Adjust your monitor mount's tension. You can adjust the vertical, tilt, and arm tension

so that the monitor stays in place when you move it.

Adjusting the vertical tension

Tilt the monitor down to access the screw. If the monitor is rising up, loosen the screw by

turning it to the left. If the monitor is falling down, tighten the screw by turning it to the right.

Caution: Do not over-tighten the screw. You

might damage the monitor or your monitor

mount.

4 mm

14

Adjusting the tilt tension

If the monitor is falling forward (screen goes down), loosen the screw by turning it to the left. If

the monitor is falling back (screen goes up), tighten the screw by turning it to the right.

Caution:

Do not remove the screw. The monitor might

fall.

Do not over-tighten the screw. You might

damage the monitor or your monitor mount.

4 mm

15

Adjusting the arm tension

To make the arm easier to move, loosen the screws by turning them to the left. To make the

arm harder to move, tighten the screws by turning them to the right.

Caution:

Do not remove the screws. The monitor might

fall.

Do not over-tighten the screws. You might

damage the monitor or your monitor mount.

2.5 mm

16

Safety and Compliance

IMPORTANT: This product will need tension adjustments after installation is complete. Make

sure that all equipment is properly installed on the product before attempting range of motion

or tension adjustments. Any time equipment is added or changed on this product resulting in a

different mounted weight, you should repeat the adjustment steps to ensure safe and optimum

operation. This product should move smoothly and easily through the full range of motion and

stay where you set it. If movement is difficult or the product does not stay where you set it,

follow the adjustment instructions to loosen or tighten the tension to create a smooth, easy

motion. Depending on your product and the adjustment, it may take many turns to notice a

difference.

affiliates.

Made in China

Page is loading ...

V2 14-1435

Made in China

Amazon Basics K001387 User manual

This manual is also suitable for

Amazon Basics K001387 User manual

in other languages

Other documents