Puretec PRO Series User manual

Brand: Puretec

Model: PRO Series

Type: User manual

Puretec PRO Series is a high-quality drinking water system that provides clean and fresh water for your home or office. It is easy to install and maintain, and it comes with a 36-month warranty. The PRO Series is designed to remove impurities from your water, including chlorine, taste, odor, particles, and turbidity. It is also effective at removing Cryptosporidium and giardia cysts. The PRO Series has a nominal flow rate of 4LPM and requires a minimum operating pressure of 300kPa. It can be used with water temperatures ranging from 3°C to 30°C.

PRO SERIES Drinking Water Systems

USER GUIDE

For correct operation & installation it is

essential to observe these instructions.

Installation & operation manual

for Drinking Water Systems

PRO Series

PURETEC CUSTOMER SERVICE

Thank you for purchasing a Puretec drinking water system. Your system is a proven performer

manufactured from only quality materials and components and will give years of ‘spring fresh’

water free of impurities if maintained properly.

Caution: Do not use with water that is microbiologically unsafe or with water of unknown

quality without adequate disinfection before or after the system.

The system is designed for metropolitan supply water but can be used in other situations. For

other types of water supply please contact your local Puretec stockist

or call our Puretec Customer Service Helpline.

The Puretec filter systems cartridges need replacing regularly to maintain optimum performance.

This is a simple procedure when following instructions. For cartridge replacements contact your

nearest Puretec stockist.

Puretec Customer Service Helpline 1300 190 190

OPERATION

Puretec systems are designed to run economically for many years and this is dependant on the

initial installation and periodical maintenance.

Flush systems for 10 minutes after any period of non-use more than 2 days. For a period of non-

use of 2 weeks or more, it may be necessary to replace cartridges.

CARTRIDGE REPLACEMENT

You can obtain replacement cartridges from your local Puretec dealer and to maintain

performance and warranty use genuine Puretec replacements.

Replacement Cartridge Guide

System Model No. Replacement Cartridge Model No.

PRO90 PX051, CB951, RET1812-24

PRO130 PX051, CB951, RET1812-36

PRO270 PX051, CB951, RET1812-60

Other cartridges are available to suit a range of requirements upon request.

PRO SERIES Drinking Water Systems

USER GUIDE

PRO SERIES Drinking Water Systems

User Guide

PRO SERIES Drinking Water Systems

USER GUIDE

CARTRIDGE INSTALLATION/CHANGEOUT

To change the filter cartridges adhere to the following procedure.

1. Close Ballvalve to prevent water ﬂow

2. Unscrew Filter Housing using the spanner wrench and discard cartridges. When removing

housings place a container underneath to catch any spillage. Membrane housing cap can be

unscrewed by hand.

3. Cleanse the inside of the housing using Puretec S500 Sanitiser. Check O-Ring and lubricate

with food grade silicone lubricant or similar. Replace O-Ring if kinked or damaged.

4. Install new cartridges and replace housing screwing them up HAND TIGHT ONLY. PX051 ﬁlter is

on the inlet side and CB951 on the outlet side.

5. Restore water supply & check for leaks, rectifying them, if any, before leaving the unit.

After installing cartridges ﬂush unit for 5 - 10 minutes.

INSTALLATION

INSTALLATION REQUIREMENTS

1. Supply pressure: 300 - 600kPa.

2. Supply temperature: 3°- 30°C.

PRO SERIES

PRO SERIES Drinking Water Systems

USER GUIDE

PRO SERIES Drinking Water Systems

INSTALLATION PROCEDURE - See Figure 1

1. The unit comes with a Tap Adapter on the inlet side, identiﬁed by GREEN hose, which will

screw onto a standard tap without the need of thread seal tape. Make sure it is ﬁrmly screwed

to provide a seal on the rubber gasket (hand tighten only).

2. To gain access to the mounting screw holes on the mounting bracket, simply unclip the

R.O. housing from the clip attached to the main mounting bracket. This will reveal the wall

mounting screw holes to enable the mounting of the system to the wall, cupboard etc.

3. Puriﬁed water (BLUE hose), and waster water (BLACK hose) lines do not come with any

attachments. Pure water should be directed to a suitable container without any back pressure

or valving occurring in the line. The drain line, or waste water may be directed to the outside

garden, or if installed inside, to a washing machine, to conserve water. If inconvenient it may

be directed to any drainage system.

4. When the unit is in place and the water lines are installed, the unit should be run for four (4)

hours before the puriﬁed water is used, on initial start up. The unit cannot be stored for more

than two weeks without use, or damaged to the membrane may occur. Please enquire if this is

the case.

For a period of non-use greater than 2 days, ﬂush for 10 min before use. For non-use greater

than 2 weeks, the cartridges may need replacing.

5. The Sediment and Chemical Removal Filters should be replaced every six (6) months. The

membrane should be replaced when water quality deteriorates or every 18-24 months,

depending on incomming water quality. A Puretec TDS meter (PTE10) can determine quality

for you at the push of a button.

For best performance use only genuine Puretec replacement cartridges and cartridges that are

suitable for this appliance.

FIGURE 1.

No. DESCRIPTION

1 Tap Adaptor

2, 2A Tube Adaptor

3 Inlet Water - Green ﬂexible tubing

4 Waste Water Outlet - Black ﬂexible tubing

5 Pure Water Outlet - Blue ﬂexible tubing

6 Membrane Housing

7 Mounting Bracket

8 Chemical Filter Housing

9 Sediment Filter Housing

9 8

SEDIMENT REMOVAL CHEMICAL REMOVAL

END VIEW OF

MEMBRANE HOUSING

User Guide

PRO SERIES Drinking Water Systems

USER GUIDE

Important Notice: Read this data sheet and compare the capabilities to your actual water

treatment needs before purchasing.

Manufacturer

Fluid Products

PO Box 64, Melrose Park

SA 5039 Australia

Phone: 1300 190 190

Seller

Name

Address

Phone:

Product: Drinking Water Filter

Model: PRO SERIES

FIGURE 2.

1. Cut the tube square and push in

to the tube stop. For metal tube

remove burrs and chamfer tube

end to prevent O-Ring seal being

damaged.

DISCONNECTION PROCEDURE

4. Push collet against body and

slide tube out of ﬁtting.

2. Fitting grips before it seals. Ensure

tube is pushed in to tube stop.

HOW TO USE QUICK CONNECT FITTINGS

3. Tube is secured in position.

PERFORMANCE DATA

PRO SERIES Drinking Water Systems

USER GUIDE

PRO SERIES Drinking Water Systems

USE GUIDELINES

• Minimumoperatingpressure300kPa.

• Maximumoperatingpressure600kPa.

• Donotallowexposuretotemperaturesbelow4°C.

• Maximumoperatingtemperature38°C.

• Nominalowrate4LPM.

• Thissystemmustbeinstalledaccordingtolocalplumbingcodesonthecoldwaterline.

• ReplacementCartridges:SeeCartridgeInstallation,page2.

• Thissystemrequiresregularreplacementoftheltercartridgetomaintainproperoperation.

Varying chlorine, sediment, or organic substance levels may aect replacement frequency.

• Besuretochangetheltercartridgesatleastevery8,000litresor6monthswhicheveroccurs

ﬁrst; or whenever you detect a change in taste, odour, or decrease in ﬂow. 8,000 litres is

approximately equal to using 20 litres daily for one year.

Caution: Do not use with water that is microbiologically unsafe or of unknown quality without

adequate disinfection before or after the system.

SUBSTANCE REDUCTION

The Water Filter models listed above have been tested and certified under AS/NZS 3497 and AS/

NZS 4348 for reduction of chlorine, odour, particles, taste and turbidity. The performance of this

product has been verified and substantiated as the test data summarised below indicates. The

Substances may not be in your water.

Class Pass Comment

Particular Reduction

III YES 75% or more

Taste, odour, chlorine reduction

IV YES 75% or more

Cryptosporidium & giardia cyst removal

IIc

YES 99.9% or more

User Guide

PRO SERIES Drinking Water Systems

USER GUIDE

PRO SERIES Drinking Water Systems

USER GUIDE

NOTES

FPS designs, manufactures and supports Puretec water care products, the name you can trust for

viable and proven water solutions. All pictures and information are supplied as a guide only.

The complete range of Puretec products are developed, refined and made to meet and exceed stringent

specifications for the worldwide market.

Important Note: Sales of products are subject to our Terms & Conditions which are available upon

request. All specifications, prices and photos are a guide only and are subject to change without

notice. Please ring to confirm details. Do not use products with microbiological unsafe water without

adequate disinfection. Where water pressure exceeds maximum pressure specifications, a pressure

limiting valve must be fitted. Maximum flow depends on cartridge, vessel, pressure, impurities etc.

WARRANTY

WARRANTY: Any claim under this warranty must be made within 36 MONTHS of the date of purchase

of the product. This product is warrantied to be free of defect of material and workmanship for 36

months from date of purchase. To make a claim under the warranty, take the product and proof of

purchase to place where you purchased the product, and they will lodge a Warranty Request with

Puretec.

Puretec will pay your reasonable, direct expenses of claiming under this warranty. You may submit

details and proof of your expense claim to place of purchase for consideration.

This warranty is given by Puretec, ABN 66 474 243 571, 14-16 Bailey Street, St Marys SA 5064,

telephone no. 1300 190 190 and email at [email protected].

This warranty is provided in addition to other rights and remedies you have under law: Our goods

come with guarantees which cannot be excluded under the Australian Consumer Law. You are entitled

to replacement or refund for a major failure and to compensation for other reasonably foreseeable

loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of

acceptable quality and the failure does not amount to a major failure.

The warranty only applies if the product was used and/or installed in accordance with the user guide

and/or installation instructions. This warranty is given in lieu of all other express or implied warranties

and manufacturer shall in no circumstance be held liable for damages consequential or otherwise or

delays caused or faulty manufacturing except as excluded by law.

Applicable to all above, is that the Warranties need to be approved by Puretec to ensure product

was not incorrectly used, installed or claimed. False and incorrect claims will be pursued at Puretec’s

discretion, including chargeable inspection and labour costs incurred.

Customer Service Helpline 1300 190 190

Email [email protected]

Web www.puretec.com.au

Puretec PRO Series User manual

Puretec PRO Series User manual

Puretec PRO Series User manual

Related papers

Other documents