EN
7
1. CONVENTIONAL
Press or to select the function, confirm by
pressing
, and then press to activate.
. CLEANING
• AUTOMATIC CLEANING PYRO
Do not touch the oven during the Pyro cycle.
Keep children and animals away from the oven
during and after (until the room has finished
airing) running the Pyro cycle.
Remove all accessories - including shelf guides - from
the oven before activating the function. If the oven is
installed below a hob, make sure that all the burners
or electric hotplates are switched off while running
the selfcleaning cycle. For optimum cleaning results,
remove the worst soiling with a damp sponge before
using the Pyro function. We recommend only running
the Pyro function if the appliance contains heavy
soiling or gives off bad odours during cooking.
Press
to show “Pyro” on the display.
Pyro
Press or to select the desired cycle, then press
to confirm. Once a cycle has been selected, if desired,
press
or to set end time (start delay), then press
to confirm.
Clean the door and remove all accessories as
prompted, then close the door and press
when
done: the oven will begin the self-cleaning cycle,
while the door locks automatically: a warning
message appears on the display, along with a
countdown indicating the status of the cycle in
progress.
Once the cycle has been completed, the door remains
locked until the temperature inside the oven has
returned to a safe level.
• DRAIN
The drain function allows the water to be drained in
order to prevent stagnation in the tank. It is advisable
to always carry out draining every time the oven has
been used.
Anyway, after a certain number of cooking this action
will be mandatory and it will not possible start a
steam function before done it.
Once selected the “Drain” function
or when suggested from display,
press
and follow the actions
indicated: Open the door and place
a large jug under the drain nozzle
located at the bottom right of the
panel. Once started the draining,
keep the jug in position until the operation is
completed.
The display will indicate when the tank has to be
completely drained.
Please note: it is not possible to perform this activity before
4 hours have elapsed from the last cycle (or the last time
the product was powered). During this wait time, the
display will show the following feedback “WATER IS HOT
- PLEASE WAIT”. The jug must be at least 2 liters large.
• DESCALE
This special function, activated at regular intervals,
allows you to keep the boiler and the steam circuit in
the best condition.
The function is divided into several phases: draining,
descaling, rinsing. Once the function is started, follow
all the steps indicated on the display and press
when done to start each phase.
The average duration of the full function is around
190 minutes.
Please note: if the function is stopped at any time, the
entire descaling cycle must be repeated.
» DRAINING
Before descaling, it will be necessary to drain tank:
to perform the operation in the best way, proceed as
described in the relative paragraph.
Please note: it is not possible to perform this activity before
4 hours have elapsed from the last cycle (or the last time
the product was powered). During this wait time, the
display will show the following feedback “WATER IS HOT
- PLEASE WAIT”. The jug must be at least 2 liters large.
» DESCALING
For best results in descaling, we recommend filling the
tank with a solution composed of 75 g of the specific
WPRO product and 1.7 litres of drinking water.
WPRO descaler is the suggested professional product
for the maintenance of the best performance of
your steam function in the oven. Please follow the
instructions for use on the packaging. For orders and
information contact the after sales service or
www.whirlpool.eu
Whirlpool will not be held responsible for any damage
caused by the use of other cleaning products available
on the market.
Once the descaling phase has been completed, the tank
has to be drained.
Please note: The jug must be at least 2 liters large.
» RINSING
To clean the tank and the steam circuit, rinse cycle
has to be done. Fill the tank with drinking water until
the display shows “TANK FULL”, then press
to start
the rinsing. At the end, the display will prompt to
repeat this phase by draining and rinsing again.
Do not turn off the oven until all the steps required
by the function have been completed.
Cooking functions cannot be activated during the
cleaning cycle.
Please note: A message will be shown on display, to remind
you to execute this operation regularly.