～ Read this rst ～
CUB-43PCI-LP/CUB-43PCIEXP Setup Guide
■ Checking Accessories
Check that all the accessories are supplied.
● Interface board（
Low-prole bracket attached
）・・・1
● CD-ROM・・・1
- Driver software
- Utility program
- User's Manual（PDF）
- Setup Guide（this book）
■ Setup Flow
＊ Never touch the terminal. Doing so may damage the terminal.
Ⅰ
Ⅱ
Ⅲ
Ⅳ
Ⅴ
To install a setup program
Shut down the PC.
Open the PC cover and insert
the interface board into the PCI bus slot.
Close the cover and power on the PC.
To conrm that the OS identied this board.
Terminal*
Terminal*
CUB-43PCI-LP CUB-43PCIEXP
1
2
1. Installing the driver with setup program
■ Manually install from the supplied CD-ROM.
① . Turn on the computer, start Windows, administrator account (such as
Administrator) please login.
＊ If you are logged in account other than "Computer Administrator", Log o, and the computer
again.Please log in with an administrator account. If any account is unknown, please check
the account that has administrative rights by "Start" → "Control Panel" → "User Accounts".
② . Open the CD that has been attached
"Driver" folder. Run in the "setup.exe".
Here, the warning screen shown at right
is displayed in the case of Windows7, but
press "Yes" button to continue.
③ . Dialog in"Welcome to the CUB-43PCIEXP
Device Driver Setup Wizard" or "Welcome
to the CUB-43PCI-LP Device Driver
Setup Wizard" will appear, press "Next >"
button to continue.
④ . Dialog of the "Ready to Install" that
appears, press "Install" button to
continue.
⑤ . The dialog box of "Wpuld you like to
install this device software" will appear
as shown on the right in the case of
Windows7,then press "Install", and
continue.
⑥ . Dialog in "Completing the CUB-
43PCIEXP Device Driver Setup Wizard"
or "Completing the CUB-43PCI-LP Device
Driver Setup Wizard" will appear and the
installation of the setup program will be
completed by pressing "Finish" button .
3
2. Install the board to the PC
① . Power o the PC.
② . Remove all the cables from the PC.
③ . Remove the PC's cover.(Follow the directions in the PC's manual for how
to remove the cover.)
④ . Please insert the PCI slot in the case
of CUB-43PCI-LP. Please insert the
PCI-Express slot in the case of CUB-
43PCEXP.Then remove the cover
from the slot that are targeted.
⑤ . Insert the interface card into a free
PCI or PCI-Express slot rmly.
⑥ . Fix the card using the screws
supplied with the PC.
⑦ . Reinstall the PC cover in the reverse procedure of ③ .
⑧ . Reconnect the cables removed in ② .
■ Refer to the PC's manual for how to open and close the cover and install and remove a PCI card.
(Follow the directions in the PC's
manual for how to remove the
cover.)
※ If you want to insert the board
to the PC with a low-prole slot,
replace the low-prole bracket
attached.
(Do not connect the cable to the connector of this board yet.)
4
3. Conrm that the PCI board is recognized.
When you launch the OS to turn on the PC after you have installed in your computer this board,
the driver is automatically applied to the OS recognizes the board.
It may be at this time, the balloon is displayed on the task tray at the bottom right of the
screen, it recognizes the new hardware, you are installing the driver is displayed.
For Windows7
Driver will be installed automatically. You do not need to operation.
For WindowsXP
① . "Welcome to the Found New Hardware
Wizard" should appear as shown on the
right in the case of Windows XP. Here,
press "Cancel" button in helping you
select, and then go.
② . Open the CD that has been attached
"Driver" folder. Run in the "setup.exe".
③ . Dialog in"Welcome to the CUB-43PCIEXP
Device Driver Setup Wizard" or "Welcome
to the CUB-43PCI-LP Device Driver
Setup Wizard" will appear, press "Next >"
button to continue.
④ . Dialog of the "Ready to Install" that
appears, press "Install" button to
continue.
⑤ . Dialog in "Completing the CUB-
43PCIEXP Device Driver Setup Wizard"
or "Completing the CUB-43PCI-LP
Device Driver Setup Wizard" will appear
and the installation of the setup program
will be completed by pressing "Finish"
button .
5
In the case of WindowsXP, open
the "Control Panel" at the beginning,
"Syetem" and then open, please open
the "Hardware" below. And open the
"Device Manager".
Here, you can double-click the "CUnet
Devices", make sure that it is: "
StepTechnica: CUB-43PCIEXP WDF
Driver" or "StepTechnica: CUB-43PCI-
LP WDF Driver".
Please open the "Device Manager"
from "Control Panel" in the case of
Windows7.
Here, you can double-click the "CUnet
Devices", make sure that it is: "Step
Technica: CUB-43PCIEXP WDF Driver"
or "Step Technica:CUB-43 PCI-LP WDF
Driver".
For Windows7
For WindowsXP
In order to conrm that the board is properly installed, rst,open the "Device
Manager".
Specications
Number of ICs MKY43
Transfer rate 3/6/12Mbps
Occupied memory area 4KB
Connector RJ-45 8 pins × 2
Consumption current 500 mA or less
Size 120mm(W) × 64mm(H)
*Panel side of the board is excluded.（Low prole correspondence）
Communication method CUnet communication method
Compatible bus
CUB-43PCI-LP PCI Ver2.2 compliant, 5V,32-bit,33-MHz extended bus
CUB-43PCIEXP PCI-EXPRESS Ver1.1 × 1compliant,extended bus
Interrupt 1 line used(CUB-43PCI-LP)
Power supply
CUB-43PCI-LP +5V
CUB-43PCIEXP +3.3V
Conditions of use Temperature 0 – 50℃ Humidity 20 － 90% (with no condensation)
Safety Precautions
Restriction
The CUB-43PCI-LP/CUB-43PCIEXP board is an evaluation board using our CUnet master IC
(MKY43).We will not be liable for results from any use other than evaluation.
When using this product for a purpose other than evaluation, be sure to verify the operation in
advance.
The contents of this guide are subject to change without any prior notice. Check for the latest
version of this guide when using this card. (You can check it with our Web site.)
Description and technical information in this guide should be treated as reference material to use
this product for your own purpose. When using this product for a practical purpose, consider the
peripheral conditions and environments on the actual board and evaluate the entire system on
your own responsibility, and design the system to be suitable for your purpose. We are not liable
for tness of this product for your system.
We are not liable for any damages or infringement of a patent or any other rights, resulting from
use of information contained in this guide, the product, circuits and other components.
We do not transfer any warranty or ownership of a third party's industrial rights, intellectual
property rights, and any other rights to anyone who use this product, information contained in this
guide, or circuits and other components.
This product is not designed for use with equipment which may aect human life. If you are
planning to use this product for such use, consult us in advance.
You cannot transfer or copy this guide in whole or in part without prior permission from us.
Developed and manufactured by Step Technica Co., Ltd
Issued: December 2014
Document No：STD-CUB43PCISU-V1.4E
Warning and Caution
6
Contact
Visit our website for contact info.
Contact us on website Contact technical support
http://www.steptechnica.com/jp/contact/index.html
TEL 04-2964-8804
Weekday AM9:00 ～ PM6:00
( A special holiday is excluded. )
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Lenovo 57094408 - IdeaCentre H210 5355AFU Desktop Upgrade Instructions
-
Airwell AWWR-WDF012-C11 User manual
-
Wacker Neuson CUB700M User manual
-
-
Cub Cadet GT 3235 User manual
-
-
-
-
E-flite UMX Carbon Cub SS BNF User manual
-