ESAB EPP-201 User manual

Brand: ESAB

Model: EPP-201

Category: Welding System

Type: User manual

Valid for serial no. 015-xxx-xxxx0558 007 904 GB 20110513

EPP-201

Instruction manual

DECLARATION OF CONFORMITY

According to

The Low Voltage Directive 2006/95/EC of 12 December 2006, entering into for ce 16 January 2007

The EMC Directive 2004/108/EC of 15 December 2004, entering into force 20 January 2005

Type of equipment

Plasma Cutting power source

Brand name or tr ade mark

ESAB

Type designation etc.

EPP--201, Valid from serial number 015 xxx xxxx (2010 w.15)

EPP--201 is used in installations for mechanized plasma cutting

Manufacturer or his authorised representative established within the EEA

Name, address, telephone number, telefax number:

ESAB AB

Esabväge n, SE--695 81 Laxå, Sweden

Phone: +46 586 81000, Fax: +46 584 411 924

The following harmonised standard in force within the EEA has been used in the design:

EN 60974--1, Arc welding equipment – Part 1: Welding power sources

EN 60974--10, Arc welding equipment – Part 10: Electromagnetic compatibility (EMC) requirements

Additional information: Restrictive use, Class A equipment, intended for use in locations other than residential.

This apparatus EPP--201 constitute a part of the electrical installation of a machine

By signing this document, the undersigned declares as manufacturer, or the manufacturer’s authorised

representative established within the EEA, that the equipment in question complies with the safety requirements

stated above.

Place and Date:

Laxå 2010--09--10

Signatur Position / Befattning

Global Direc tor

Equipment and Automation

Kent Eimbrodt

Clarification

-2-

-3-

TOCe

Rights reserved to alter specifications without notice.

1SAFETY 4...........................................................

2 INTRODUCTION 6...................................................

2.1 Equipment 6................................................................

2.2 Properties and function 6.....................................................

3 TECHNICAL DATA 6.................................................

4 INSTALLATION 7....................................................

4.1 Lifting instructions 8.........................................................

4.2 Delivery check 8............................................................

4.3 Location 8..................................................................

4.4 Mains supply 9..............................................................

4.4.1 Connecting the incoming mains cable 9....................................

4.5 Supply and return cables (supplied by the customer) 10...........................

4.5.1 Connection of supply and return cables 10..................................

4.6 Parallel installation 11.........................................................

4.6.1 Parallel connection of two power sources 11................................

4.6.2 Marking with two parallel connected power sources 12........................

4.7 Connections for supply cables 13...............................................

5 OPERATION 14.......................................................

5.1 Connections and control devices 14............................................

5.1.1 Key to symbols 15.......................................................

5.1.2 Control panel 15.........................................................

5.2 Operate modes 16...........................................................

5.2.1 Power source in single operation (used with CNC, there are two basic operating modes)

5.2.2 Several power sources 18................................................

5.3 Starting cutting and marking 18................................................

6 MAINTENANCE 19....................................................

6.1 Inspection and cleaning 20....................................................

7 FAULT-TRACING 20..................................................

7.1 List of fault codes 21..........................................................

8 ORDERING SPARE PARTS 22.........................................

DIAGRAM 24............................................................

ORDERING NUMBER 29.................................................

-4-

bp06de1

1SAFETY

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or

near the equipment observes all the relevant safety precautions. Safety precautions must meet the

requirements that apply to this type of equipment. The following recommendations should be ob-

served in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the equip-

ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in-

jury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

S its operation

S location of emergency stops

S its function

S relevant safety precautions

S welding and cutting

2. The operator must ensure that:

S no unauthorized person is stationed within the working area of the equipment when it is

started up.

S no-one is unprotected when the arc is struck

3. The workplace must:

S be suitable for the purpose

S be free from drafts

4. Personal safety equipment

S Always wear recommended personal safety equipment, such as safety glasses, flame-proof

clothing, safety gloves.

S Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

S Make sure the return cable is connected securely.

S Work on high voltage equipment may only be carried out by a qualified electrician.

S Appropriate fire extinquishing equipment must be clearly marked and close at hand.

S Lubrication and maintenance must not be carried out on the equipment during operation.

-5-

bp06de1

WARNING

Read and understand the instruction manual before installing or operating.

Arc welding and cutting can be injurious to yourself and others. Take precausions when welding and

cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard

data.

ELECTRIC SHOCK - Can kill

S Install and earth the unit in accordance with applicable s tandards.

S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

S Insulate yourself from earth and the workpiece.

S Ensure your working stance is safe.

FUMES AND GASES - Can be dangerous to health

S Keep your head out of the fumes.

S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS - Can injure eyes and burn skin.

S Protect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

S Protect bystanders with suitable screens or curtains.

FIRE HAZARD

S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE - Excessive noise can damage hearing

S Protect your ears. Use earmuffs or other hearing protection.

S Warn bystanders of the risk.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

WARNING

Do not use the power source for thawing frozen pipes.

CAUTION

Class A equipment is not intended for use in residential locations where

the electrical power is provided by the public low-voltage supply system.

There may be potential difficulties in ensuring electromagnetic

compatibility of class A equipment in those locations, due to conducted

as well as radiated disturbances.

CAUTION

This product is solely intended for plasma cutting.

CAUTION

Read and understand the instruction manual before

installing or operating.

-6-

bp06de1

Dispose of electronic equipment at the recycling facility!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical and/or

electronic equipment that has reached the end of its life must be disposed of at a

recycling facility.

As the person responsible for the equipment, it is your responsibility to obtain

information on approved collection stations.

For further information contact the nearest ESAB dealer.

2 INTRODUCTION

Plasma power source EPP 201 is designed for marking and mechanical high speed

plasma cutting. It can be used with, for example, torches PT-15, PT-19XLS, PT-600

and PT-36 together with Smart Flow II, a computer controlled system for gas control

and reconnection.

2.1 Equipment

The power source is supplied with:

S Instruction manual

2.2 Properties and function

S Fan cooled

S Protection in the event of connecting the incorrect power supply

S Thermal protection in the event of overload

S Can be connected in parallel to increase the current range.

3 TECHNICAL DATA

EPP201

Mains voltage

3~ 380 V, 400 V +/–10 %, 50 Hz

Mains supply Ssc min. 7.2 MVA

Zmax. 0.020 Ω

Primary current lmax 64 A at 380 V, 59 A at 400 V

Setting range

marking

cutting

5 A - 200 A

10 A - 36 A

30 A - 200 A

Permissible load

duty cycle 100 %

200 A / 160 V

Efficiency at maximum current 90 %

Power factor at maximum current 0,90

Open-circuit voltage U

342 V at 380 V

360 V at 400 V

Operating temperature -10to40°C

Transportation temperature -20to55°C

-7-

bp06de1

EPP201

Dimensions, l x w x h 1200 x 603 x 1035 mm

Weight 475 kg

Enclosure class IP21

Mains supply, S

sc min

Minimum short circuit power on the network in accordance with IEC 61000-3-12

Mains supply, Z

max

Maximum permissible line impedance of the network in accordance with IEC 61000-3-11.

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at

a certain load without overloading. The duty cycle is valid for 40° C.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Apparatus marked IP21 are intended for indoor use.

4 INSTALLATION

The installation must be executed by a professional.

WARNING!

ELECTRIC SHOCKS CAN KILL

Take precautionary measures against electric shocks. Ensure that all power

supplies are disconnected

– switch off the switch at the wall socket and pull out

the equipment's power cable from the socket before making any electrical

connections in the power source.

WARNING!

Failure to follow these instructions can lead to serious personal injury, death or

property damage. Follow the instructions to prevent accidents and injuries.

Observe local and national electrical safety regulations.

WARNING!

Incorrect earthing can result in personal injury or death. The chassis must be

connected to approved protective earth. Ensure that protective earth is not

connected to any phase terminals by mistake.

CAUTION

This product is intended for industrial use. In a domestic environment this product may

cause radio interference. It is the user's responsibility to take adequate precautions.

-8-

bp06de1

CAUTION!

Conducting dust and contaminants inside the power source can cause electrical flashovers.

This can damage the equipment. If dust is allowed to collect inside to the power source,

short-circuits can occur (see the chapter regarding maintenance).

4.1 Lifting instructions

WARNING

The product must be lifted using a fork

lift truck or as follows:

4.2 Delivery check

1. Remove the packaging and inspect the equipment for damage that was not

immediately apparent upon reception of the delivery.

Immediately report any damage to the delivery company.

2. Check that here are no loose parts in the packaging before it is recycled.

3. Check the cooling air gaps and ensure that any obstacles are removed from

there.

4.3 Location

S Minimum permitted distance to walls or other cold air obstructions in front of and

behind the power source is 1 m.

S Place the power source so that the top and side panels can be removed for

maintenance, cleaning and inspection.

S Place the power source relatively close to a correctly fused mains socket.

S Keep the surface under the power source clean, so that the cold air does not

bring any contaminants in with it.

S The area around the equipment must be as free of dust and vapour as possible

and also be as cool as possible. These factors affect the cooling capacity.

-9-

bp06de1

4.4 Mains supply

The power source is 3-phase driven. The power supply must be taken from a socket

equipped with a switch, anti-surges or MCBs, in accordance with local regulations.

Recommended fuse sizes an d minimum cable area

ESP 150 50 Hz

Mains voltage 380 V 400 V

Mains cable area mm

4 G 35*) 4 G 35*)

Phase current I

1eff

64 A 59 A

Fuse, anti-surge 100 A 100 A

*) Supplied by the customer.

NOTE! The mains cable areas and fuse sizes as shown above are in accordance with Swedish

regulations. Use the power source in accordance with the relevant national regulations.

4.4.1 Connecting the incoming mains cable

1 Opening for mains cable in

the rear panel

2 Main earth terminal 3 Phase terminals

1. Remove the small panel from the reverse of the power source.

2. Insert the mains cable through the opening in the rear panel.

3. Secure the cable with the strain relief at the opening.

4. Connect the protective earth to the chassis's main earth terminal.

5. Connect the phase conductors to the phase terminals.

6. Reinstall the panel on the r everse before powering the equipment.

-10-

bp06de1

4.5 Supply and return cables (supplied by the customer)

Supply and return cables for plasma cutting must have a copper conductor with

cross section of 105 mm

per 400 A and be rated for at least 600 V.

4.5.1 Connection of supply and return cables

1. Open the safety plate from the front of the power source.

2. Insert the cables through the openings at the bottom of the power source

immediately behind the front panel.

3. Connect the cables to the output terminals in the power source.

4. Close the front panel.

Closed front protective panel

Open front protective panel

-11-

bp06de1

4.6 Parallel installation

Two power sources can be connected in parallel for higher current.

4.6.1 Parallel connection of two power sources

CAUTION!

The main power source has the electrode conductor (negative conductor) jumpered. The

auxiliary power source has the return conductor (positive conductor) jumpered.

1. Connect outgoing negative cables to the arc start box (high frequency

generator).

2. Connect the outgoing positive cables to the workpiece.

3. Connect positive and negative cables between the power sources.

4. Connect the pilot arc cable to the pilot arc terminal in the power source. The

auxiliary power source pilot arc connection is not used. The pilot arc cir cuit is not

connected in parallel.

5. Connect a parallel control cable between both power sources.

6. Connect the CNC control cable to the main power source.

The power source does not have a m ains voltage switch. Then mains voltage is

switched off using the switch at the power socket.

Parallel connection of two power sources when bo t h power sources are used.

EPP-201 EPP-201

Auxiliary power source Main power source

Return cable Electrode Return cable Electrode

(+) (-) (+) Pilot arc (-)

Control

cable to

cooling unit

Parallel control cable for power

sources

CNC

control

cable

2 pcs positive

cables

600 V 105 mm

to the work-

piece

1 pcs 600 V conductor

2.5 mm

arc start box (high frequency

generator)

2 pcs negative cables

600 V 105 mm

in arc start box

(high frequency

generator)

-12-

bp06de1

Parallel connection of two power sources when only one power source is

used.

EPP-201 EPP-201

Auxiliary power source Main power source

Return

cable

Electrode Return

cable

Electrode

(+) (-) (+) (-)

Parallel control

cable for power sources

Control cable to

cooling unit

To reset from parallel operation to

single operation, disconnect the

negative cables from the auxiliary

power source and isolate the cable

ends.

2 pcs positive

cables

600 V 105 mm

to the workpiece

2 pcs negative cables 600 V 105 mm

in arc start box

(high frequency generator)

4.6.2 Marking with two parallel conn ected power sou rces

Two parallel connected EPP-201s can be used for marking down to 10 A and for

cutting from 30 A to 400 A.

Operation with two parallel conn ected power so urces

1. The signal supply main power source with digital logic signals for start/stop,

marking/cutting and current range high, and either digital logic input signals or

analogue input signals for controlling pilot current signals to the m a in power

source for both marking and cutting. Both power sources switch on during

marking, but the au x iliary power source's current output switches off when

marking signals are given.

-13-

bp06de1

4.7 Connections for supply cables

1 Remote operation (CNC) 2 Parallel connected power source

3 Cooling unit 4 Emergency stop connection

-14-

bp06de2

5OPERATION

General safety regulations for the handling of the equipment can be found on

page 4. Read through before you start using the equipment!

5.1 Connections and control devices

1 Connection for cooling unit 9 Voltmeter

2 Connection for parallel connected power

source

10 Switch for control panel or remote control

unit

3 Connection for remote control unit, CNC unit 11 Switch for actual and setpoint value display

4 MCB for CNC unit. 12 Controls for current settings

5 Emergency stop 13 Connection for emergency stop

6 Ammeter 14 Connecting mains cable (supplied by the

customer)

7 Red indicating lamp, restart error 15 Fuse 15 A

8 Orange indicating lamp - Overheating

-15-

bp06de2

5.1.1 Key to symbols

Over heating (8) Fault indication (7)

Emergency stop (5)

Emergency stop

connection (13)

Local operation (10) Remote control unit (10)

Pilot arc current (11) Current (12)

5.1.2 Control panel

Switch actual valu e/setp o in t valu e d isp lay (11)

S Middle position: the cutting parameters; actual value is displayed.

S Up mode: setpoint value for pilot arc current during local operation or remote

operation is displayed.

S Mode down: setpoint value for cutting current during local operation or remote

operation is displayed.

Overheating protection (8)

Lights when the power source has overheated.

Fault indication (7)

Lights in the event of a fault that requires the power source to be restarted.

Current control potentiometer (12)

The range for the power source is 30 to 200 A. Only used in “PANEL” mode.

Switch co n t rol panel / remote o p eration (10)

This switch is used to select where the current is controlled from.

S With the switch in the local control mode, PANEL, use the current potentiometer.

S With the switch in the remote control mode, REMOTE, the current is controlled

by external signal (CNC).

Display window (6, 9)

Displays voltage and current during cutting. T he ammeter can be activated before

cutting is started, to give an indication of how high the cutting or marking current or

pilot arc current will be, see A above. The display window also shows any fault

codes.

Emergency sto p co n n ectio n (13)

The emergency stop connection gives access to the emergency stop's breaking

contact. The contact is connected to J4-A and J4-B and breaks when the emergency

stop button is pressed. Th is gives a signal to the plasma cutting equipment stating

that the power source is in emergency stop m ode.

-16-

bp06de2

Emergency stop button (5)

The emergency stop button affects the emergency stop switch. When the button is

pressed, emergency stop status is active. T he power source cannot provide any

power, even if a start signal is given.

Miniature circuit breaker (MCB) CB1 - 3 A (4)

Switch for 115 VAC to CNC unit.

5.2 Operate modes

In cutting mode, the outgoing current on the power source can be regulated

steplessly from 30 to 200 A using the current potentiometer on the control panel or

with a remote reference signal connected to J1.

When remote reference signals are used, 1 V corresponds to 36 A and 200

corresponds to signal voltage of 5.55 VDC.

The power source has cutting as standard setting. To switch to marking m ode, the

control signal for this m ust be supplied from a remote control unit.

The switch is set to marking mode with an external, isolated relay or external,

isolated switch that connects J1-R (115 VAC) with J1-C. The electrical circuit

diagram is in the inside of the rear panel. Contact closure for m arking mode must

occur at least 50 m s before command for start or contact on is given.

In CNC marking mode, the outgoing current can b e regulated steplessly from 0 to 36

A using a remote reference signal connected to J1. In local operated marking mode,

the outgoing current can be regulated steplessly from 0 to 18 A using the current

potentiometer on the control panel (standard setting upon delivery). If SW1-1, which

is open on the control panel, closes, the range becomes 0 to 18 A.

When remote reference signals are used, 1 V corresponds to 3.6 A and 36 A

corresponds to signal voltage of 10.00 VDC.

5.2.1 Powe r source in single operati on (us ed with CNC, there a re tw o basi c

operating modes)

1. Local operation from control panel – (switch on the power source) Switch for

local/remote operation in local control mode, PANEL. Used with limited CNC

unit, which only provides start/stop signals to the power source. The

micro-control unit in the power source uses the control panel potentiometer's

analogue setting as setpoint signal for cutting current. From these values, the

micro control unit calculates initial current, pilot arc current and ramp up time.

The current values for cutting and pilot arc can be displayed before cutting, by

moving the return sprung switch to the position for display of the setpoint value

for cutting current respectively pilot arc current. If the pilot arc current seems to

be insufficient the CNC unit can increase it by sending out output signals on

inputs PA0 and PA1. The current increases as follows.

PAO PA1

no signal no signal no change

signal no signal the current increases by 12.5 %

no signal signal the current increases by 2,5 %

signal signal the current increases by 37,5 %

-17-

bp06de2

See diagram on page24.

The table below, which is used to calculate starting current, pilot arc current and

ramp up time, is stored in the micro control unit.

Cutting current

(A)

Start current

(A)

Pilot arc current

(A)

Ramp up time

(ms)

30 20 15 200

50 25 20 250

100 50 25 500

200 100 30 800

If other values than the table values used for the cutting current, the corresponding

values are calculated assuming a linear ramp for all required parameters.

2. Remote control mode

a. Partial CNC operation – (CNC cable pin V open, open for internal control).

The switch for local/remote operation must be in the REMOTE mode. T he

CNC unit must supply setpoint values for cutting current and start/stop

signals to the power source. The micro-control unit in the power source

calculates initial current, pilot arc current and ramp up time from the setpoint

value for cutting current.

b. Remote control mode with full CNC operation – (CNC cable pin V closed,

closed for internal control). The switch for local/remote operation must be in

the REMOTE mode. The CNC unit m ust activate the input for full CNC

control on pin V in the connection cable. In this mode, all parameters are

controlled by the CNC unit, including initial current, pilot arc current and

ramp times. T he pilot arc current can be controlled using a digital logic input

signals or analogue input signals. If the analogue input signal is less than 0.5

V, the power source uses the digital logic signals on the inputs PA0 and PA1

to supply the required pilot arc current, based on the following combination.

PAO PA1 Pilot arc current (A)

no signal no signal 10

signal no signal 20

no signal signal 30

signal signal 40

If analogue reference signals are used, 10 VDC gives 45 A and 1 VDC 4.5 A.

Marking – Can be carried out in local operating mode remote control mode. The

input for marking mode must be closed in the CNC unit. In local operating mode,

the marking current is set using the potentiometer on the control panel.

Maximum marking current is 36 A. If SW1-1, which is open on the control panel,

closes, the range becomes max. 0 to 18 A. In remote control mode, the marking

current is regulated by a remote reference signal, 10 VDC gives 36 A and 1 VDC

gives 3.6 A marking current.

-18-

bp06de2

5.2.2 Several power so u rces

1. Parallel connected operation – Connect the power sources according to section

3.6. Set the switch for local/remote operation in REMOTE mode, on both power

sources. If the units are used for cutting and both power sources are to supply

cutting current, activate the logic input HI CURRENT (pin T) in the CNC cable.

With this setting, the maximum current is 400 A at analogue input signal 10 VDC

from CNC. If the input HI CURRENT is deactivated, the auxiliary source's current

outout switches off, despite it being connected to the main power source. Only

the main power source produces current in marking mode. If marking and cutting

are carried alternately the input HI CURRENT can be left active, whereupon the

input for marking is controlled if both the power sources' current outputs or only

the main power source' s is to be active. The current range when marking is 10 to

36 A and when cutting 30 to 400 A.

5.3 Starting cutting and marking

1. Power the equipment by switching on the switch at the power socket ( the power

source does not have its own mains power switch). When the current source is

powered, the display window briefly shows EPP-201 and then Pr x.xx, (the

program version number) and then 0 A and 0 V.

2. Set the switch for local/remote operation in the desired m ode, depending on

whether the CNC unit can be remotely controlled.

a. During local operation (PANEL mode) you can display the set setpoint value

for cutting current by keeping the switch on the control panel in the position

for display of setpoint for cutting current. In PANEL mode, the power source

calculates pilot arc current, initial current and ramp up time from the set

cutting current setpoint value. You can display the set setpoint value for pilot

arc current by keeping the switch on the control panel in the position for

display of setpoint for pilot arc current. See section 5.1.2 Control panel.

b. In remote control mode, there are two possible operating modes.

1 The standard mode is similar to local operating mode, but the cutting

current signal comes from the CNC unit instead of from the control

panel's potentiometer. The scale for the current signal during remote

control operation is 1.0 VDC = 36 A. This mode can be used if the CNC

unit does not have functions for controlling initial current and ramp times.

Connections for remote control are based on the schedule for the CNC

interface.

2 If the CNC unit has functions for controlling the initial current and ramp

times, set the switch for local/remote control in REMOTE m ode, and

connects the pins R and V in the CNC contact. In this mode, the CNC

unit supplies analogue signals for controlling the values for initial current,

ramp up time and cutting current. The scale is the same as in the

standard mode. The pilot arc current is regulated by another analogue

signal, 0–10 VDC, if applicable, or using a binary signal according to the

schedule for the CNC unit's interface. The scale for the pilot arc current

signal is 10 VDC = 45 A.

3. Start plasma cutting. Variables such as gas pressure, flow, torch height etc. may

need to be set.

4. If cutting/marking, for any reason, cannot be initiated, the power source displays

a fault code that indicates the cause o f the fault, see Fault codes in the fault

tracing section.

-19-

bp06de2

6 MAINTENANCE

CAUTION

All guarantee undertakings from the supplier cease to apply if the customer himself

attempts any work in the product during the guarantee period in order to rectify any faults.

WARNING!

ELECTRIC SHOCKS CAN KILL

Switch off the switch at the power socket before starting maintenance work.

WARNING!

Risk of eye injuries when blow cleaning with compressed air.

Use approved eye protection with side guards when cleaning the power

source.

Only use low pressure air.

WARNING!

Risk of electric shock!

Always reinstall all covers that were removed when cleaning, before switching the

power back on.

CAUTION!

The maintenance may only carried out by persons with the appropriate training.

CAUTION!

If the cold air flow is blocked for any reason, EPP-201 can overheat.

The thermo switches can then deploy and prevent continued operation.

Do not use air filters on this power source.

Keep cold air passages clear of dust and obstructions.

Regular maintenance is important for safe, reliable operation.

Only those persons who have appropriate electrical knowledge (authorized

personnel) may remove the safety plates.

-20-

bp06de2

6.1 Inspection and cleaning

The following points on the power source should be checked and/or cleaned

regularly.

1. Check the return cable connection to the workpiece.

2. Check that the protective earth from the work piece is securely connected to the

power source chassis earth.

3. Check the torch heat shield. Replace it if it is damaged.

4. Check the electrode and the nozzle for wear daily. Remove any splash, r eplace

the electrode and nozzle as necessary.

5. Check that the cables or hoses are not damaged or bent.

6. Check that all plugs and connections and ground terminal are firmly connected.

7. Using dry, clean, low pressure compressed air, blow clean any dust from all air

ducts from all components, especially from cooling fins in the front part of the

power source. Dust is a heat insulator and reduces the cooling capacity. Use eye

protection.

8. Ensure that all incoming power supplies are disconnected. Use goggles and face

mask and blow clean the power source internally using dry compressed air at

low pressure .

7 FAULT-TRACING

WARNING!

ELECTRIC SHOCKS CAN KILL

Never allow persons other than those with the applicable knowledge to check or

repair the equipment. Electrical work must always be carried out by authorised

electricians.

CAUTION!

Stop all work immediately if the power source does not work correctly.

Only allow qualified people to fault trace the equipment.

Only use recommended spare parts.

Page is loading ...

ESAB EPP-201 User manual

Brand: ESAB

Model: EPP-201

Category: Welding System

Type: User manual

Download PDF

report

ESAB EPP-201 User manual

ESAB EPP-201 User manual

Related papers

Other documents