ESAB W82 Aristo® User manual
- Category
- Welding System
- Type
- User manual
This manual is also suitable for
Aristo®
Instruction manual
0460 971 101 GB 20140521 Valid for: W82:905-,944- xxx-xxxx RetrofitW82:419-xxx-xxxx
W8
2
TABLE OF CONTENTS
0460 971 101 © ESAB AB 2014
1 SAFETY ................................................................................................................ 4
2 INTRODUCTION................................................................................................... 7
2.1 Equipment............................................................................................................. 7
3 TECHNICAL DATA ............................................................................................... 8
4 INSTALLATION..................................................................................................... 9
4.1 Mains supply ........................................................................................................ 9
4.2 Assembly instruction...........................................................................................9
4.3 System description ............................................................................................ 10
4.4 How to set-up the U82 for use with W82..........................................................10
4.4.1 Save your stored data ...................................................................................... 10
4.4.2 Convert the U82 stand alone unit to a presentation unit .................................. 11
4.5 Systems diagrams ............................................................................................. 11
5 OPERATION ....................................................................................................... 13
5.1 Connections and control devices.....................................................................13
5.2 Overheating protection......................................................................................13
6 MAINTENANCE.................................................................................................. 14
6.1 Inspection and cleaning .................................................................................... 14
7 ORDERING SPARE PARTS ............................................................................... 15
DIAGRAM ..................................................................................................................16
ORDERING NUMBERS.............................................................................................19
ACCESSORIES .........................................................................................................20
Rights reserved to alter specifications without notice.
1 SAFETY
0460 971 101
- 4 -
© ESAB AB 2014
1 SAFETY
NOTE!
The unit is tested by ESAB in a general set-up. The responsibility for safety and
function, of the specific set-up, lies with the integrator.
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
2. The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment when it
is started up
○ no-one is unprotected when the arc is struck or work is started with the equipment
3. The workplace must:
○ be suitable for the purpose
○ be free from drafts
4. Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could
become trapped or cause burns
5. General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinquishing equipment must be clearly marked and close at hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
CAUTION!
This product is solely intended for arc welding.
1 SAFETY
0460 971 101
- 5 -
© ESAB AB 2014
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting. Ask for your employer's safety practices which should
be based on manufacturers' hazard data.
ELECTRIC SHOCK - Can kill
• Install and earth the unit in accordance with applicable standards
• Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing
• Insulate yourself from earth and the workpiece
• Ensure your working stance is safe
FUMES AND GASES - Can be dangerous to health
• Keep your head out of the fumes
• Use ventilation, extraction at the arc, or both, to take fumes and gases away
from your breathing zone and the general area
ARC RAYS - Can injure eyes and burn skin.
• Protect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing
• Protect bystanders with suitable screens or curtains
FIRE HAZARD
• Sparks (spatter) can cause fire. Make sure therefore that there are no
inflammable materials nearby
NOISE - Excessive noise can damage hearing
• Protect your ears. Use earmuffs or other hearing protection. Protect your
ears. Use earmuffs or other hearing protection
• Warn bystanders of the risk
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be potential
difficulties in ensuring electromagnetic compatibility of
class A equipment in those locations, due to conducted
as well as radiated disturbances.
1 SAFETY
0460 971 101
- 6 -
© ESAB AB 2014
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2012/19/EC on
Waste Electrical and Electronic Equipment and its
implementation in accordance with national law, electrical
and/or electronic equipment that has reached the end of
its life must be disposed of at a recycling facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved collection
stations.
For further information contact the nearest ESAB dealer.
CAUTION!
Read and understand the instruction manual before
installing or operating.
ESAB can provide you with all necessary welding protection and accessories.
2 INTRODUCTION
0460 971 101
- 7 -
© ESAB AB 2014
2 INTRODUCTION
W8
2
is a control unit and it exists in two different chassis:
Aristo® W8
2
W8
2
is a control unit that adjusts the communication between
welding equipment and automation equipment, such as robots and
computers. Communication protocols: DeviceNet, Profibus,
CANopen and Ethernet.
W8
2
is used together with ESAB's CANbus equipped power sources
for welding automation. For power source and wire feed unit
handling, see the relevant instruction manual.
Retrofit Aristo® W8
2
Retrofit Aristo® W8
2
is retrofitted on top of supported ESAB power
sources. It connects to the CANbus internally. Communication
protocol: WeldLink.
For information about supported power sources, contact your ESAB
sales representative.
2.1 Equipment
Aristo® W8
2
• W8
2
DeviceNet, W8
2
Profibus, W8
2
CANopen and W8
2
Ethernet are supplied with a
USB memory and an instruction manual.
• W8
2
Integrated is supplied with an instruction manual.
Retrofit Aristo® W8
2
• Retrofit Aristo® W8
2
is supplied with the software WeldLink and an instruction manual.
Measurement cable kit and connection cables for different power sources are available as
accessories, see "ACCESSORIES" chapter and separate spare parts list.
Instruction manuals in other languages can be downloaded from the Internet:
www.esab.com
3 TECHNICAL DATA
0460 971 101
- 8 -
© ESAB AB 2014
3 TECHNICAL DATA
Aristo® W8
2
Supply voltage (to feed unit through W8
2
) 42 V, 50-60 Hz
Supply voltage (from robot) 24 V DC
Supply voltage (from power source) 12 V DC
Weight 4 kg
Dimensions (l × w × h) 366 × 101 × 159 mm
Enclosure class IP 23
Retrofit Aristo® W8
2
Supply voltage (from power source) 12 V DC
Supply current (max) 1.0 A (12 V DC)
Weight 3.6 kg
Dimensions (l × w × h) 477 × 250 × 90 mm
Enclosure class IP 23
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP23 is intended for indoor and outdoor use.
4 INSTALLATION
0460 971 101
- 9 -
© ESAB AB 2014
4 INSTALLATION
The installation must be carried out by a professional.
See the service manual for Aristo® W8
2
.
4.1 Mains supply
NOTE!
Mains supply requirements
High power equipment may, due to the primary current drawn from the mains
supply, influence the power quality of the grid. Therefore connection restrictions
or requirements regarding the maximum permissible mains impedance or the
required minimum supply capacity at the interface point to the public grid may
apply for some types of equipment (see technical data). In this case it is the
responsibility of the installer or user of the equipment to ensure, by consultation
with the distribution network operator if necessary, that the equipment may be
connected.
4.2 Assembly instruction
Connection of Aristo® W82 to ESAB's Mig 5000i power source
1. Remove the welding power source's rear
handle by removing the screws.
2. Put the W8
2
onto the welding power
source.
3. Screw the W8
2
and the handle into place
in the same screw holes.
Connection of Retrofit Aristo® W82
For instructions on how to connect the Retrofit Aristo® W8
2
, see the Service manual for W8
2
or contact the nearest ESAB Service Center or distributor.
Connection of Aristo® W82 to ESAB's Mig 3001i, Mig 4001i and Mig 6502c power
sources
Connect the W8
2
with a 2 m cable and place it on the floor or on a stand next to the power
source.
4 INSTALLATION
0460 971 101
- 10 -
© ESAB AB 2014
4.3 System description
It is possible to configure the U8
2
unit for stand-alone usage (stand-alone unit) or
presentation usage (presentation unit). The presence of a W8
2
unit within the welding system
determines which unit that is to be used.
The stand-alone unit is used when there is
no W8
2
unit in the system.
The presentation unit is used when there
is a W8
2
unit in the system.
It is necessary to convert the U8
2
stand-alone unit to a U8
2
presentation unit before it is used
together with a W8
2
unit.
During unit start-up it is possible to see if the unit is a presentation unit or not.
4.4 How to set-up the U82 for use with W82
NOTE!
It is necessary to change the U8
2
stand-alone unit to a presentation unit before it
is used together with a W8
2
unit.
4.4.1 Save your stored data
1. Connect the U8
2
stand-alone unit to a power source or a wire feed unit.
2. Turn on the power source's main switch.
3. Export weld data sets from the U8
2
memory to a USB memory (see chapter
Export/Import in the U8
2
instruction manual).
4. Turn off the power source's main switch.
5. Remove the USB memory.
4 INSTALLATION
0460 971 101
- 11 -
© ESAB AB 2014
4.4.2 Convert the U82 stand alone unit to a presentation unit
1. Connect the enclosed USB memory to a PC. Make sure that the computer is set to show
file extensions.
2. Rename:"update.txt_" to "update.txt"and "reset.txt_" to "reset.txt"
3. Open the cover on the left-hand end of the
control panel.
4. Insert the enclosed USB-memory into the
USB connector.
5. Close the cover.
6. Turn on the power source's main switch.
One “beep” indicates that convert process
is started It is finished when two “beeps”
are heard.
7. Turn off the power source's main switch.
8. Open the cover and remove the enclosed
USB memory.
9. Close the cover. The unit is now ready to be used together with a W8
2
unit.
4.5 Systems diagrams
Schematic diagrams showing the connection between different units follow.
1. Connection between welding power source and W82 - “CAN to power source“.
2. Connection between W82 and robot control cabinet - “Fieldbus”.
3. Connection between welding power source and wire feed unit - “Internal CAN”.
4. Connection between welding power source and control panel - “Internal CAN”.
NOTE!
If the wire feed unit, RoboFeed, is not used, a separate arc voltage feedback is
required to the measurement contact on the control unit.
4 INSTALLATION
0460 971 101
- 12 -
© ESAB AB 2014
5 OPERATION
0460 971 101
- 13 -
© ESAB AB 2014
5 OPERATION
General safety regulations for handling the equipment can be found in the "SAFETY"
chapter of this manual. Read it through before you start using the equipment!
5.1 Connections and control devices
1. Indicating lamp from serial number 944-xxx-xxxx
Orange indicating lamp - Overheating
2. Fieldbus
Connection for communication with robot system
3. Measure
Connection for measurement cable for arc voltage feedback and emergency stop signal,
measurement kit
4. Internal CAN
Connections for communication with ESAB wire feed unit and control panel
5. LAN
Connection to network, Ethernet
6. CAN to welding power source
Connection for communication with welding power source
7. USB
USB memory connection
5.2 Overheating protection
The control unit has overheating protection that operates if the temperature becomes too
high. When this occurs the welding current is interrupted and the orange lamp is on.
The overheating protection resets automatically when the temperature has fallen and the
lamp goes out.
6 MAINTENANCE
0460 971 101
- 14 -
© ESAB AB 2014
6 MAINTENANCE
NOTE!
Regular maintenance is important for safe, reliable operation.
CAUTION!
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates.
CAUTION!
All warranty undertakings from the supplier cease to apply if the customer
attempts any work to rectify any faults in the product during the warranty period.
6.1 Inspection and cleaning
Regularly check that the control unit is in electrical contact with the power source and that
the connections are fault-free and correctly connected.
7 ORDERING SPARE PARTS
0460 971 101
- 15 -
© ESAB AB 2014
7 ORDERING SPARE PARTS
W8
2
is designed and tested in accordance with the international and European
standards 60974-1 and 60974-10. It is the obligation of the service unit which has
carried out the service or repair work to make sure that the product still conforms to
the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the back cover of this
document. When ordering, please state product type, serial number, designation and spare
part number in accordance with the spare parts list. This facilitates dispatch and ensures
correct delivery.
DIAGRAM
0460 971 101
- 16 -
© ESAB AB 2014
DIAGRAM
Aristo® W8
2
DIAGRAM
0460 971 101
- 17 -
© ESAB AB 2014
DIAGRAM
0460 971 101
- 18 -
© ESAB AB 2014
Retrofit Aristo® W8
2
ORDERING NUMBERS
0460 971 101
- 19 -
© ESAB AB 2014
ORDERING NUMBERS
Ordering no. Denomination
0460 891 880 Aristo® W8
2
, Integrated
0460 891 881 Aristo® W8
2
, DeviceNet
0460 891 882 Aristo® W8
2
, Profibus
0460 891 883 Aristo® W8
2
, CANopen
0460 891 884 Aristo® W8
2
, Ethernet
0465 826 881 Retrofit Aristo® W8
2
0459 839 038 Spare parts list W8
2
0740 800 203 Service manual W8
2
Instruction manuals and the spare parts list are available on the Internet at: www.esab.com
ACCESSORIES
0460 971 101
- 20 -
© ESAB AB 2014
ACCESSORIES
0456 527 885 Control cable (connectors included)*
0.45 m, 12 poles
0462 000 880 Control cable (connectors included)*
2 m, 10 - 12 poles
0461 182 880 Connection set CAN Robot for Aristo®
W8
2
Integrated*
7.5 m
0462 062 001 USB memory 2 Gb
0459 314 880 Terminating resistor*
*Not applicable for Retrofit Aristo® W8
2
with ordering number 0465 826 881.
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
ESAB W82 Aristo® User manual
- Category
- Welding System
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
