RM6XX0
7 U / 8 U / 9 U R a c k m o u n t M o n i t o r
1 7 ” / 1 9 ” / 20” T F T L C D
Industrial
Monitors
User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please visit Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA91710 Tel: 909.597.7588 Fax: 909.597.1939
© Copyright 2015 Acnodes Corp.
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this
document is subject to change without notice. We are not liable for any injury or loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
● Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
● Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
● When installing , place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
● When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
● Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
● If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
● Observe all precautions and warnings attached to the equipment.
● If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
● Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
● Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
● If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
● Any product, on which the serial number has been defaced, modified or removed.
● Damage, deterioration or malfunction resulting from:
● Accident, misuse, neglect, fire, water, lightn ing, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
● Repair or attempted repair by anyone not authorized by us.
● Any damage of the product due to shipment.
● Removal or installation of the product.
● Causes external to the product, such as electric power fluctuation or failure.
● Use of supplies or parts not meeting our specifications.
● Normal wear and tea r.
● Any other causes which does not relate to a product defect.
● Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
● Re-position or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Contents
< Part. 1 > RM6170I 6190NI 6210
1.1 Package Content
1.2 Structure Diagram & Dimension
1.3 Installation
P.1
P.1 - 4
P.5
< Part. 2 > Specifications I OSD I Remote Controller
2.1 Product Specifications
2.2 On-screen Display Operation ( OSD )
P.6 - 9
P.10 - 11
< Part. 3 > Options
3.1 3G / HD / SD-SDI Broadcast-grade input ( except RM6170 )
3.2 MCS Multi-display control solution
3.3 AV2.2D Upgrade : DVI-D + VGA + BNC + S-Video + Audio
3.4 AV2.2H Upgrade : HDMI + VGA + BNC + S-Video + Audio
3.5 17” / 19” Touchscreen : Resistive, Capacitive
20” Touchscreen : Resistive
3.6 48V, 24V or 12VDC power
3.7 MIL-type or lockable connector
P.12
P.13
P.14
P.14
P.15
P.16
P.17
P.18
Before Installation
● It is very important to mount the equipment in a suitable cabinet or on a stable surface.
● Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
How To Clean Your LCD Monitor
Caution :
● To avoid the r isk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
● When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
● Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the finish.
● Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
● Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
1
Disconnect the power cord.
2
Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1
Disconnect the power cord.
2
Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3
Gently wipe the surface. Use as little pressure as possible.
4
Wait until your monitor is completely dry before plugging it in and powering it up.
RM6210
Rear view
RM6190N
< Part 1 >
< 1.1 > Package Content
RM 6170 or 6190N or 6210 X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
< 1.2 > Structure Diagram
Front view
RM6170
1
2
3
Power adapter
1 LCD panel
4
2
LCD membrane
3 Audio speaker
4 Power adapter basket
Power cord
DVI-D
Audio
Power BNC S-Video
VGA
HDMI
Standard
out - in - in
Video PC
: DVI-D + VGA
AV2.2D upgrade : DVI-D + VGA + BNC + S-Video + audio
AV2.2H upgrade : HDMI + VGA + BNC + S-Video + audio
Option : SDI, USB for touchscreen & DC power
< 1.2 > Dimension- RM6190N
Front View Side View
Bottom View
UNIT : mm
1mm = 0.03937 inch
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
RM6190N
480 x 53.3 x 354.8 mm
18.9 x 2.1 x 14 inch
529 x 124 x 495 mm
23 x 4.9 x 20.8 inch
6.5 kg
14 lbs
9 kg
20 lbs
< 1.3 > Installation
RM6170I 6190N
RM6210
Step
1
● Mount the display panel with M6 screw set.
● M6 screw x 4 pcs required ( Left & right side ).
M6 screw sets are not provided.
Step
2
● Fix the LCD into the rack.
Step
1
● Mount the display panel with M6 screw set.
● M6 screw x 8 pcs required ( Left & right side ).
M 6 screw sets are not provided.
Step
2
● Fix the LCD into the rack.
< Part 2 >
< 2.1 > Product Specifications - RM6170I RM6190N
LCD
Panel
RM6170
RM6190N
Manufacturer
Panel Size ( diagonal )
17-inch TFT color LCD
19-inch TFT color LCD
Display pixel ( dots x lines )
1280 x 1024
1280 x 1024
Brightness ( typ. )
250
250
Contrast Ratio ( typ. )
1000:1
1000:1
Color
16.7 M
16.7 M
Viewing Angle ( L/R/U/D )
80/80/80/80
80/80/80/80
Response Time ( ms )
5
5
Dot pitch ( mm )
0.264
0.294
Display Area ( mm )
337.92H x 270.33V
376.32H x 301.05V
Surface treatment
Haze 25%, Hard-coating
Surface hardness
3H
3H
Backlight Type
CCFL
CCFL
MTBF ( hrs )
50,000
50,000
Video
Connectivity
Digital
HDMI
HDMI 1.1, CEA-861-D
DVI
DVI-D, TMDS single link
Analog
VGA
Analog 0.7Vp-p
Composite ( BNC )
NTSC & PAL
S-Video ( 4-pin )
NTSC & PAL
Plug & Play
DVI / VGA
VESA EDID structure 1.3
Synchronization
VGA
Separate, Composite & SOG
Audio
Connectivity
Audio Input
Connector
3.5mm stereo jack
Impedance / Power level
30kK / 750mV
Audio Output
Connector
3.5mm stereo jack
Resistance / Power level
30kK / 2.8V
Speaker Output
Power
2 x 2W
*When the audio output is connected, speaker output is OFF
Regulatory
Safety Approval
FCC & CE
Power
Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption
Screen display ON
25W or less
Power saving mode
4W or less
Power button OFF
1W or less
Environmental
Conditions
Operating
Temperature
0 to 50°C degree
Humidity
20~90%, non-condensing
Storage
Temperature
-5 to 60°C degree
Humidity
5~90%, non- condensing
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Physical
Specification
RM6170
RM6190N
Product ( W x D x H )
480 x 54.2 x 310 mm
18.9 x 2.1 x 12.2 inch
480 x 53.3 x 354.8 mm
18.9 x 2.1 x 14 inch
Packing ( W x D x H )
529 x 124 x 495 mm
20.8 x 4.9 x 19.5 inch
529 x 124 x 495 mm
20.8 x 4.9 x 19.5 inch
Net Weight
6 kgs / 13 lbs
6.5 kgs / 14 lbs
Gross Weight
8.5 kgs / 19 lbs
9 kgs / 20 lbs
Applicable
Format
DVI-D / VGA Input
PC Signal
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 760 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
< Part 2 >
< 2.1 > Product Specifications - RM6210
LCD
Panel
Manufacturer
Panel Size ( diagonal )
20-inch TFT color LCD
Display pixel ( dots x lines )
1600 x 1200
Brightness ( typ. )
300
Contrast Ratio ( typ. )
800:1
Color
16.7 M
Viewing Angle ( L/R/U/D )
89/89/89/89
Response Time ( ms )
16
Dot pitch ( mm )
0.255
Display Area ( mm )
408.00H x 306.00V
Surface treatment
Anti-glare, Hard-coating
Surface hardness
3H
Backlight Type
CCFL
MTBF ( hrs )
45,000
Video
Connectivity
Digital
HDMI
HDMI 1.1, CEA-861-D
DVI
DVI-D, TMDS single link
Analog
VGA
Analog 0.7Vp- p
Composite ( BNC )
NTSC & PAL
S-Video ( 4-pin )
NTSC & PAL
Plug & Play
DVI / VGA
VESA EDID structure 1.3
Synchronization
VGA
Separate, Composite & SOG
Audio
Connectivity
Audio Input
Connector
3.5mm stereo jack
Impedance / Power level
30kK / 750mV
Audio Output
Connector
3.5mm stereo jack
Resistance / Power level
30kK / 2.8V
Speaker Output
Power
2 x 2W
*When the audio output is connected, speaker output is OFF
Power
Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption
Screen display ON
48W or less
Power saving mode
4W or less
Power button OFF
1W or less
Regulatory
Safety Approval
FCC & CE
Environmental
Conditions
Operating
Tem perature
0 to 50°C degree
Humidity
20~90%, non-condensing
Storage
Tem perature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Physical
Specification
Product ( W x D x H )
480 x 63.5 x 399 mm
18.9 x 2.5 x 15.7 inch
Packing ( W x D x H )
583 x 124 x 529 mm
23 x 4.9 x 20.8 inch
Net Weight
8.5 kgs / 19 lbs
Gross Weight
11 kgs / 24 lbs
Applicable
Format
DVI-D / VGA Input
PC Signal
1600 x 1200 x 60Hz
1400 x 1050 x 60Hz
1440 x 900 x 60Hz
1360 x 768 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 760 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
< 2.2 > On-screen Display Operation ( OSD )
RM6190N
Power light
Green = On
Orange = Power saving
Membrane Switch Function
Power on / off LCD
Display the OSD menu
Scrolls through menu options and adjusts the displayed control
(To auto adjustment by pressing the button for 5 seconds)
Exit the OSD screen
Toggle analog, digital & video connection (DVI-D and video options only)
RM6170IRM6210
Membrane Switch Function
Turn the monitor on or off
Display the OSD menu
Act as an Enter key to select screen setting options
Scroll through menu options and adjust
the displayed control
Exit the OSD screen
Go back to the previous on-screen sub-menu or
main menu
Remark : All LED touch buttons in WHITE light.
The LED of Power touch button will flash continuously when there is no signal input.
1
All the LED touch buttons will automatically turn off after 10 minutes of idle status ( except the Power ).
2
Light up all membrane buttons, please press any button for 1 - 2 seconds ( except the Power ).
< 2.2 > On-screen Display Operation ( OSD )
OSD Configuration Page
Image:
for the brightness, contrast, color temp, red, green, and blue
Geometry:
for the auto adjust, H position, V position, phase and clock
Video:
for the colour, tint, sharpness, noise reduction, DCDi and TV Setup
Audio:
for volume, bass, treble, balance, AVL and mute
Misc:
for the language, OSD position, graphic mode, ratio, reset and timer
< Part 3 >
< 3 .1 > Options : 3G I HD I SD-SDI input
Acnodes ’ SDI input is an ideal solution for the broadcast-
grade video and high resolution CCTV market.
Designed for use with F ull HD 1080p and ultra high resolution
1920 x 1200 LCD displays, Acnodes provides a SDI input
module without using additional space or power and it com es
standard with a 2- year warrant y.
DVI-D
Audio
out - in - in
Video PC
Po wer BNC S-Video
VGA
SDI
out
- in
HDMI
*** F or SDI option, the AD board will be upgraded to AV3. 0, and this comes standard with HDMI, DVI-D,
VG A, S-Video, BNC and audio inputs.
INPUT
3 G-SDI IN
BNC x 1 / 0 .8 Vp-p ( 75 ohm )
3 G-SDI O UT
BNC x 1 / Active through, equalized & r eloc ked
Standard Com plian ce
Video
SMPT E 425 M / 274 M / 296 M / 125 M
ITU-R BT. 656
Audio
SMPT E 299 M / 272 M-C
Com patible Video F ormat
3 G-SDI
1080 p
@ 60 / 50 Hz, 4: 2 :2
1080 p
@ 30 / 25 / 24 Hz, 4 :4 :4
1080 i
@ 60 / 50 Hz, 4: 4 :4
720p
@ 60 / 50 Hz, 4: 4 :4
HD-SDI
1080 p
@ 30 / 25 / 24 Hz, 4 :2 :2
1080 i
@ 60 / 50 Hz, 4: 2 :2
720p
@ 60 / 50 Hz, 4: 2 :2
SD-SDI
480i
@ 60Hz, 4:2 : 2
IT U-R BT.656
576i
@ 50Hz, 4:2 : 2
Com patible Audio F ormat
3 G-SDI
48 kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
HD-SDI
48 kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
SD-SDI
48 kHz, 16 / 20 / 24 bit, 2 CH, Synchronized /
As ynchronized Video
Max. Transm ission Distance
75 ohm coaxial cab le
3 G-SDI
150m at 2 .97G b/ s
HD-SDI
250m at 1 .485 Gb/s
SD-SDI
480m at 270 Mb/s
< 3.2 > Options : MCS
( Multi-display Control )
More control is always good. Especially when it is necessary and
easy. Acnodes provides MCS solution to control the OSD of
various LCD display up to 64 units.
The RS-232C is used for the communication between the PC and the
first display via a 15 feet serial cable while the CAN bus is used for the
various LCD displays cascade together via CAT 5/6 cable, and daisy
chain up to 1,000 meters.
Designed for use with various LCD displays, Acnodes provides a
MCS input module without using additional space or power and it
comes standard with a 2- year warranty.
*** For MCS option, casing depth will be changed.
RS-232C
Set switch
For the 1st and last display,
push the set switch upward
15 feet serial cable
( over 15 feet, extender required )
For other daisy chain displays,
push the set switch downward
LINK OUT IN OUT IN OUT IN
OUT
RJ-45 jack
Cat5 / 6 cable
max. 300 meters
Cat5 / 6 cable
max. 300 meters
Daisy chain up to 1,000
meters and 64 displays
Cat5 / 6 cable
max. 300 meters
up to 64 displays
Link
set out in
DVI-D
VGA
MCS
out - in - in
Video PC
Power BNC S-Video
Audio
HDMI
< 3.3 > AV2.2D Upgrade Options :
-
DVI-D
-
AV
-
Audio
( DVI-D TMDS single link )
( S-Video + Composite, BNC )
( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers )
< 3.4 > AV2.2H Upgrade Options :
-
HDMI
( HDMI 1.1, CEA-861-D )
-
AV
-
Audio
( S-Video + Composite, BNC )
( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers )
out - in - in
Video PC
HDMI
Power BNC S-Video VGA
Audio
out - in - in
Video PC
Power BNC S-Video VGA
Audio
DVI-D
< 3.5 > Options : Touchscreen & driver
17” I 19" USB Touchscreen Specification
Model
17’
19”
17”
19”
TRB
e-Resistive
TCB
e-Capacitive
Technology
5-Wire Resistive
Capacitive
Touch Point
Single
Single
Method
Stylus or Finger
Finger
Activation Force
= 50g / Stylus=R0.8
= 50g
Durability
35 million touches
300 million touches
Response Time
15 ms
20 ms
Optical Transmittance
80% ± 3%
93% ±2%
Surface Hardness
3H
9H
Haze
8% ± 3%
7%
Glass
1.4 ±0.2 mm
3.2 ±0.2 mm
2.8 mm ±10%
2.8 mm ±10%
Connector
USB Type A
USB Type A
Compatibility
Windows 7 / XP / Vista, Linux
Windows 7 / XP / Vista, Linux
20" USB Touchscreen Specification
Model
TRB
e-Resistive
Technology
5-Wire Resistive
Touch Point
Single
Method
Stylus or Finger
Activation Force
= 50g / Stylus=R0.8
Durability
35 million touches
Response Time
15 ms
Optical Transmittance
80% ± 3%
Surface Hardness
3H
Haze
8% ± 3%
Glass
3.2 ±0.2 mm
Connector
USB Type A
Compatibility
Windows 7 / XP / Vista, Linux
●
USB touchscreen package includes 1 x 6ft USB cable, quick reference guideline and CD disc
●
For detailed information, please refer to the attached CD disc
●
As the touchscreen unit is not made of toughened glass, please handle it carefully
USB Touchscreen
DVI-D Power VGA
< 3.5 > Options : Touchscreen & driver
Please follow the below steps to setup the touch screen:-
Step 1. Run the bundled CD disc
Step 2. Double click the Setup.exe
Step 3. Follow the installation instruction to finish the setup
Step 4. After installation, run the TouchKit program & the “4 point calibration”
Please do the initial calibration
after the first setup
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Acnodes RM6170 User manual
- Category
- Touch screen monitors
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Synergy Global Technology LCDR7U19-02 User manual
-
Tote Vision LCD-800 User manual
-
-
Synergy Global Technology ID-HE19Aw User manual
-
Add-On Computer Peripherals (ACP) DVID2DVIDSL6F Datasheet
-
-
Eclipse Rackmount MP Serie Owner's manual
-
-
-
AVLink VGA-EDXW PRO Owner's manual
