Desa Tech CISAW Owner's manual

Brand: Desa Tech

Model: CISAW

Category: Fireplaces

Type: Owner's manual

For more information, visit www.desatech.com

WARNING: If the information in this manual is not

followed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

UNVENTED (VENT-FREE) GAS STOVE HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

MODELS SVYD18NRA AND SVYD18PRA

REMOTE-READY CONTROL GAS LOG HEATER

(BURNER SYSTEM FOR CAST IRON STOVES)

OXFORD™

Patent Pending

VICTOR HEARTH

www.desatech.com

113084-01J2

SAFETY

WARNING: The SVYD-

18NRA/PRA series vent-

free gas log heater is only

approved for use in the

VCIS(*) series, PVCIS(*)

series or VH(*)A series

cast iron stove models.

(* Indicates Color Sufx Designation)

WARNING: Improper

installation, adjustment,

alteration, service or main-

tenance can cause injury

or property damage. Refer

to this manual for correct

installation and operation-

al procedures. For assis-

tance or additional infor-

mation consult a qualied

installer, service agency or

the gas supplier.

WARNING: This is an

unvented gas-red heater.

It uses air (oxygen) from the

room in which it is installed.

Provisions for adequate

combustion and ventila-

tion air must be provided.

Refer to Air for Combustion

and Ventilation section on

page 5 of this manual.

This appliance may be in-

stalled in an aftermarket,*

permanently located,

manufactured (mobile)

home, where not prohib-

ited by local codes.

This appliance is only for

use with the type of gas

indicated on the rating

plate. This appliance is

not convertible for use

with other gases.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

WARNING: This product

contains and/or generates

chemicals known to the state

of California to cause cancer or

birth defects or other reproduc-

tive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble,

operate or service this heater.

Improper use of this heater can

cause serious injury or death

from burns, fire, explosion,

electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

TABLE OF CONTENTS

Safety .................................................................. 2

Product Identication ........................................... 4

Local Codes......................................................... 5

Product Features ................................................. 5

Air For Combustion And Ventilation ..................... 5

Installation ........................................................... 8

Operation ........................................................... 14

Inspecting Burners............................................. 17

Cleaning and Maintenance ................................ 18

Troubleshooting ................................................. 19

Parts .................................................................. 22

Specications .................................................... 26

Wiring Diagram .................................................. 26

Replacement Parts ............................................ 26

Technical Service............................................... 26

Service Hints ..................................................... 26

Accessories ....................................................... 27

Warranty ..............................................Back Cover

www.desatech.com

113084-01J 3

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the

u, with headaches, dizziness or nausea. If

you have these signs, the heater may not

be working properly. Get fresh air at once!

Have heater serviced. Some people are

more affected by carbon monoxide than oth-

ers. These include pregnant women, people

with heart or lung disease or anemia, those

under the inuence of alcohol and those at

high altitudes.

Natural and Propane/LP Gas: Natural and

propane/LP gases are odorless. An odor-

making agent is added to the gas. The odor

helps you detect a gas leak. However, the

odor added to the gas can fade. Gas may be

present even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this heater.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not use a

blower insert, heat exchanger

insert or other accessory not ap-

proved for use with this heater.

WARNING: Do not allow fans

to blow directly into the heater.

Avoid any drafts that alter burner

ame patterns. Ceiling fans can

create drafts that alter burner

ame patterns. Altered burner

patterns can cause sooting.

Due to high temperatures, the

appliance should be located out

of trafc and away from furniture

and draperies.

Do not place clothing or other

ammable material on or near

the appliance. Never place any

objects on the heater.

SAFETY

Continued

Stove becomes very hot when

running heater. Keep children

and adults away from hot surface

to avoid burns or clothing igni-

tion. Heater will remain hot for a

time after shutdown. Allow sur-

face to cool before touching.

Carefully supervise young

children when they are in the

room with stove. When using

the optional hand-held remote

accessory, keep selector switch

in the OFF position to prevent

children from turning on burners

with remote.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other am-

mable vapors and liquids.

1. This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases.

2. Do not place propane/LP supply tank(s)

inside any structure. Locate propane/LP

supply tank(s) outdoors (propane/LP units

only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instructions

• if you cannot reach your gas supplier,

call the re department

4. This heater shall not be installed in a

bedroom or bathroom.

5. Do not use this stove as a wood burning

replace. Use only model SVYD18PRA/

NRA series vent-free gas log heater for

VCIS(*), PVCIS(*) and VH(*)A series cast

iron stove models.

www.desatech.com

113084-01J4

6. Do not add extra logs or ornaments such as

pine cones, vermiculite or rock wool. Using

these added items can cause sooting.

7. This log heater is designed to be smoke-

less. If logs ever appear to smoke, turn off

heater and call a qualied service person.

Note: During initial operation, slight smok-

ing could occur due to log curing and

heater burning manufacturing residues.

8. To prevent the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 18.

9. Before using furniture polish, wax, carpet

cleaners or similar products, turn heater

off. If heated, the vapors from these prod-

ucts may create a white powder residue

within burner box or on adjacent walls or

furniture.

10. This heater needs fresh, outside air ven-

tilation to run properly. This heater has an

Oxygen Depletion Sensing (ODS) safety

shutoff system. The ODS shuts down the

heater if not enough fresh air is available.

See Air for Combustion and Ventilation,

page 5. If heater keeps shutting off, see

Troubleshooting, page 19.

SAFETY

Continued

11. Do not run heater

• where ammable liquids or vapors are

used or stored

• under dusty conditions

12. Do not use this stove to cook food or burn

paper or other objects.

13. Do not use heater if any part has been ex-

posed to or under water. Immediately call

a qualied service technician to inspect

the room heater and to replace any part

of the control system and any gas control

which has been under water.

14. Do not operate heater if any log is broken.

Do not operate heater if a log is chipped

(dime-sized or larger).

15. Turn heater off and let cool before servic-

ing. Only a qualied service person should

service and repair heater.

16. Operating heater above elevations of

4,500 feet could cause pilot outage.

17. To prevent performance problems, the use

of a propane/LP tank of less than 100 lb.

capacity (propane/LP units only).

18. Provide adequate clearances around air

openings.

Figure 1 - Typical Stove Cabinet Model with Gas Log Heater

(Shown is Oxford™ Model with Model SVYD18PRA/NRA Heater)

Stove

Body

Stove Door

(Shown in the

open position)

Piezo

Ignitor

Control Knob

One Piece

Log Set Inside

Stove Cavity

Gas Log Heater

Base Assembly

Flame Adjustment Knob

Optional Remote

Selector Switch

PRODUCT IDENTIFICATION

www.desatech.com

113084-01J 5

LOCAL CODES

AIR FOR COMBUSTION AND VENTILATION

Install and use heater with care. Follow all

local codes. In the absence of local codes,

use the latest edition of The National Fuel

Gas Code, ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

State of Massachusetts: The installation

must be made by a licensed plumber or

gas tter in the Commonwealth of Mas-

sachusetts.

Sellers of unvented propane or natural

gas-red supplemental room heaters shall

provide to each purchaser a copy of 527

CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for

bedroom and bathroom installation in the

Commonwealth of Massachusetts.

PRODUCT FEATURES

OPERATION

This heater is clean burning. It requires no

outside venting. There is no heat loss out a

vent or up a chimney. Heat is generated by

realistic, dancing yellow ames. This heater

is designed for vent-free operation. State and

local codes in some areas prohibit the use of

vent-free heaters.

SAFETY PILOT

This heater has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free

room heaters. The ODS/pilot shuts off the

heater if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system re-

quires no matches, batteries or other sources

to light heater.

WARNING: This heater shall

not be installed in a room or

space unless the required vol-

ume of indoor combustion air

is provided by the method de-

scribed in the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, the

International Fuel Gas Code, or

applicable local codes. Read the

following instructions to insure

proper fresh air for this and

other fuel-burning appliances

in your home.

Today’s homes are built more energy efcient

than ever. New materials, increased insulation

and new construction methods help reduce

heat loss in homes. Home owners weather

strip and caulk around windows and doors

to keep the cold air out and the warm air in.

During heating months, home owners want

their homes as airtight as possible.

While it is good to make your home energy

efcient, your home needs to breathe. Fresh

air must enter your home. All fuel-burning ap-

pliances need fresh air for proper combustion

and ventilation.

Exhaust fans, replaces, clothes dryers and

fuel burning appliances draw air from the house

to operate. You must provide adequate fresh

air for these appliances. This will insure proper

venting of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation.

All spaces in homes fall into one of the three

following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 5 through 7 will help

you classify your space and provide adequate

ventilation.

www.desatech.com

113084-01J6

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion

and ventilation. However, in buildings of un-

usually tight construction, you must provide

additional fresh air.

Unusually tight construction is dened as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6 x 10

-11

kg per pa-sec-m

) or

less with openings gasketed or sealed

and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window

and door frames, between sole plates

and oors, between wall-ceiling joints,

between wall panels, at penetrations

for plumbing, electrical and gas lines

and at other openings.

If your home meets all of these three criteria,

you must provide additional fresh air. See

Ventilation Air From Outdoors, page 7.

If your home does not meet all of the three

criteria above, proceed to Determining Fresh-

Air Flow For Fireplace Location.

Conned and Unconned Space

The National Fuel Gas Code, ANSI Z223.1/

NFPA 54 denes a conned space as a space

whose volume is less than 50 cubic feet per

1,000 Btu/hr (4.8 m

per kw) of the aggregate

input rating of all appliances installed in that

space and an unconned space as a space

whose volume is not less than 50 cubic feet

per 1,000 Btu/hr (4.8 m

per kw) of the ag-

gregate input rating of all appliances installed

in that space. Rooms communicating directly

with the space in which the appliances are

installed*, through openings not furnished

with doors, are considered a part of the un-

conned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation

grills between them.

AIR FOR COMBUSTION AND VENTILATION

Continued

DETERMINING FRESH-AIR FLOW

FOR HEATER LOCATION

Determining if You Have a Conned or

Unconned Space

Use this work sheet to determine if you have

a conned or unconned space.

Space: Includes the room in which you will install

replace plus any adjoining rooms with door-

less passageways or ventilation grills between

the rooms.

1. Determine the volume of the space (length

x width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2560 cu. ft.

(volume of space)

If additional ventilation to adjoining room

is supplied with grills or openings, add the

volume of these rooms to the total volume

of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can sup-

port.

________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20

= 51,200 (maximum Btu/Hr the space can

support)

3. Add the Btu/Hr of all fuel burning appliances

in the space.

Vent-free replace __________ Btu/Hr

Gas water heater* __________ Btu/Hr

Gas furnace __________ Btu/Hr

Vented gas heater __________ Btu/Hr

Gas replace logs __________ Btu/Hr

Other gas appliances* + _________ Btu/Hr

Total = _________ Btu/Hr

* Do not include direct-vent gas appliances.

Direct-vent draws combustion air from the

outdoors and vents to the outdoors.

Example:

Gas water heater __________ Btu/Hr

Vent-free replace + _________ Btu/Hr

Total = _________ Btu/Hr

4. Compare the maximum Btu/Hr the space

can support with the actual amount of Btu/Hr

used.

_______ Btu/Hr (maximum the space can

support)

_______ Btu/Hr (actual amount of Btu/Hr

used)

40,000

30,000

70,000

www.desatech.com

113084-01J 7

Example: 51,200 Btu/Hr (maximum the

space can support)

70,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the above example is a conned

space because the actual Btu/Hr used is more

than the maximum Btu/Hr the space can sup-

port. You must provide additional fresh air. Your

options are as follows:

A. Rework worksheet, adding the space of an

adjoining room. If the extra space provides

an unconned space, remove door to adjoin-

ing room or add ventilation grills between

rooms. See Ventilation Air From Inside

Building.

B. Vent room directly to the outdoors. See

Ventilation Air From Outdoors.

C. Install a lower Btu/Hr replace, if lower Btu/

Hr size makes room unconned.

If the actual Btu/Hr used is less than the maxi-

mum Btu/Hr the space can support, the space is

an unconned space. You will need no additional

fresh air ventilation.

WARNING: If the area in which

the heater may be operated does

not meet the required volume for

indoor combustion air, combus-

tion and ventilation air shall be

provided by one of the methods

described in the National Fuel

Gas Code, ANSI Z223.1/NFPA 54,

the International Fuel Gas Code,

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining

unconned space. When ventilating to an

adjoining unconned space, you must provide

two permanent openings: one within 12" of the

ceiling and one within 12" of the oor on the

wall connecting the two spaces (see options

1 and 2, Figure 2). You can also remove door

into adjoining room (see option 3, Figure 2).

Follow the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, Air for Combustion and

Ventilation for required size of ventilation

grills or ducts.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two perma-

nent openings: one within 12" of the ceiling

and one within 12" of the oor. Connect these

items directly to the outdoors or spaces open

to the outdoors. These spaces include attics

and crawl spaces. Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation for required size

of ventilation grills or ducts.

IMPORTANT: Do not provide openings for

inlet or outlet air into attic if attic has a thermo-

stat-controlled power vent. Heated air entering

the attic will activate the power vent.

AIR FOR COMBUSTION AND VENTILATION

Continued

Figure 3 - Ventilation Air from Outdoors

(Oxford™ Stove Model Shown)

Figure 2 - Ventilation Air from Inside

Building (Oxford™ Stove Model Shown)

Outlet

Air

V e ntilated

Attic

Outlet

Air

Inlet

Air

Inlet Air

V e ntilated

Crawl Space

T o

Crawl

Space

T o Attic

Remove

Door into

Adjoining

Room,

Option

V e ntilation Grills

Into Adjoining Room,

Option 2

V e ntilation

Grills

Into Adjoining

Room,

Option 1

12"

www.desatech.com

113084-01J8

INSTALLATION

IMPORTANT: Vent-free heaters add moisture

to the air. Although this is benecial, installing

heater in rooms without enough ventilation

air may cause mildew to form from too much

moisture. See Air for Combustion and Ventila-

tion, page 5.

CHECK GAS TYPE

Use only the correct type of gas (natural or

propane/LP). If your gas supply is not the

correct gas type, do not install heater. Call

dealer where you bought heater for proper

type heater.

WARNING: This appliance is

equipped for either natural gas

or propane/LP gas but not both.

Gas type is indicated on the rat-

ing plate. Field conversion is not

permitted.

CLEARANCES TO COMBUSTIBLES

WARNING: Maintain the

minimum clearances. If you can,

provide greater clearances from

oor, ceiling and adjoining side

and back walls.

Carefully follow the instructions below. This

stove is a freestanding unit designed to set

directly on the oor. IMPORTANT: You must

maintain minimum wall and ceiling clearances

during installation. The minimum clearances

are shown in Figure 4, page 9. Measure from

outermost point of stove top.

Minimum Wall and Ceiling Clearances

(see Figure 4, page 9)

A. Clearances from outermost point of stove

top to any combustible side wall should

not be less than 12".

B. Clearances from outermost point of stove

top to any combustible back wall should

not be less than 6" (includes corner instal-

lations).

C. Clearances from the stove top to the ceil-

ing should not be less than 48".

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualied ser-

vice person must install re-

place. Follow all local codes.

WARNING: Never install the

heater

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing or other ammable

objects are less than 42" from

the front, top or sides of the

heater

• in high trafc areas

• in windy or drafty areas

CAUTION: This heater cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to heater. Installing

heater next to vinyl or cloth wall

coverings or operating heater

where impurities (such as, but

not limited to, tobacco smoke,

aromatic candles, cleaning u-

ids, oil or kerosene lamps, etc.) in

the air exist, may discolor walls

or cause odors.

www.desatech.com

113084-01J 9

Minimum

48"

Minimum

Ceiling

Floor

Back

Wall

INSTALLATION

Continued

Figure 4 - Minimum Clearance to Walls

and Ceiling (Stove May Vary Depending

on Model)

Top View

Side

View

12"

Minimum

12"

Minimum

48"

Minimum

Ceiling

Side

Wall

Side

Wall

Back Wall

Side Wall Side Wall

12 "

Minimum

12 "

Minimum

6 "

Minimum

Corner

Wall

6 "

Minimum

6 "

Minimum

Front of

Stove Unit

Front

View

STOVE CAVITY ASSEMBLY

1. Lift off corrugated box enclosing stove

body crating.

2. Remove all screws fastening wood frame

enclosure. Spread wood frame open and

lift away from plastic-bagged stove body.

The bottom pieces of pallet wood will

remain bolted to stove body.

3. Remove plastic bag from stove body.

4. Remove all contents from inside stove

cavity. Contents include:

(4) - Legs (include leg leveler bolts)

(1) - Bottom door

(3) - Top grates

(1) - Hardware kit bag with fasteners

5. Carefully lay stove body on back to attach

bottom components to stove body (see

Figure 5). Rest stove on drop cloth or

blanket to avoid scratching stove edges.

6. Remove remaining pallet wood attached

to bottom of stove body (see Figure 6).

Use an adjustable wrench or 12 mm

socket to remove bolts.

7. Fasten each leg to stove with four M8

x 1.25 - 20 mm bolts. Use a at washer

and lock washer with each bolt. Tighten

bolts into threaded holes on stove body

(see Figures 7 and 8, page 10). Use an

adjustable wrench or a 12 mm socket.

Figure 5 - Laying Down Stove On Side

(Stove Style May Vary Depending on

Model)

Front of

Stove

Unit

Drop

Cloth/

Blanket

Pallet Wood Bolted to

Stove Body Bottom

Top of

Stove Unit

Front of

Stove Unit

Top of

Stove

Unit

Figure 6 - Removing Pallet Wood From

the Bottom of the Stove

Pallet Wood

Bolt

Pallet

Wood

Bottom

Of Stove

Unit

Front

Front of

Stove Unit

www.desatech.com

113084-01J10

INSTALLATION

Continued

8. Attach stove door by inserting step bolt

through door hinge pivot hole and into

threaded hole in stove body (see Figure 7

and Figure 10). Use an adjustable wrench

or a 12 mm socket to fasten step bolt.

Tighten step bolt until snug. Make sure

door moves freely.

9. Remove log box and heater from carton.

Place heater in stove as shown in Figure

9. Use bolts from hardware kit to attach

heater to stove.

10. Install door catch bolt (M8 x 1.25-55 mm

with two M8 hex nuts) into threaded hole on

stove body (see Figure 7). Use an adjust-

able wrench or a 12 mm socket. The catch

bolt has two hex nuts attached to it (see

Figure 11). Top nut is a bolt stop and bottom

nut is for door leveling adjustment.

11. Check general catch bolt alignment with

door claw. Make nal adjustment and door

leveling after stove is in normal standing

position.

12. Carefully lift stove back up on its four at-

tached legs.

13. Remove gas log heater from carton.

Note: Do not pick up gas log heater by the

burner itself. This could damage heater.

Always handle the gas log heater by the

heater base only.

14. Fasten stove pan to stove with two M6 x 1

- 25 mm bolts. Use a at washer and lock

washer with each bolt. Tighten bolts into

threaded holes on stove body (see Fig-

ures 7 and 9). Use an adjustable wrench

or a 10 mm socket.

15. Set top grates into stove top.

Figure 7 - Locating Threaded Holes

for Stove Bottom, Legs and Door

Attachment (Appearance May Vary

Depending on Model)

Leg

Hole

Leg Hole

Door Hinge

Step Bolt Hole

Door Catch Bolt

With Adjustable

Hex Nuts Hole

Holes for

Stove

Bottom

Front

Bottom Of

Stove Unit

Figure 8 - Attaching Stove Legs

(Oxford™ Model Shown)

Bottom Of

Stove Unit

Leg

Bolt

Washers

Figure 9 - Attaching Stove Pan (Oxford™

Model Shown)

Threaded Holes

in Stove Body

Bolt

Washers

Stove Pan

Figure 10 - Attaching Stove Door

(Appearance May Vary Depending on Model)

Stove

Bottom

Step

Bolt

Door

Hinge

Threaded

Hole

Stove

Door

Bolt Shoulder

Figure 11 - Catch Bolt and Door Claw

Orientation

Adjusting

Nut

Bolt Stop

Catch

Bolt

Door

Claw

Door

www.desatech.com

113084-01J 11

INSTALLATION

Continued

CAUTION: Do not remove the

data plates attached to the heater

base assembly. The data plates

contain important warranty and

safety information.

WARNING: Failure to posi-

tion the parts in accordance

with these diagrams or failure

to use only parts specically

approved with this heater may

result in property damage or

personal injury.

INSTALLING GAS LOG INTO STOVE

1. Remove log from carton.

2. Remove all protective packaging applied

to log for shipment.

3. Check log for any shipping damage. If

damaged (pieces larger than the size of a

dime), promptly inform dealer where you

bought heater.

4. Set one-piece log on heater base as

shown in Figure 12. Make sure middle

section at bottom of log is seated into “U”

shaped cutout in center of heater base.

Log will t securely on base. IMPORTANT:

Make sure log does not cover any burner

ports and does not touch the stove cavity

(see Figure 13).

5. Fasten back panel to stove with four M6

x 1 bolts and washers.

6. Place freestanding stove in desired posi-

tion in room. Be sure to maintain clear-

ances to combustibles as outlined on

page 8.

CAUTION: After installa-

tion and periodically thereafter,

check to ensure that no ame

comes in contact with any log.

With the heater set to HI, check

to see if ames contact any log. If

so, reposition logs according to

the log installation instructions

in this manual. Flames contact-

ing logs will create soot.

Burner Porting Areas (double

slotted rectangular openings)

Figure 13 - Top View of One-Piece Log

Set on Gas Log Heater

Safety Pilot Location

One-Piece

Log Set

One-Piece

Log Set

“U” Shaped

Cutout in Chassis

Burner

Middle

Section at

Bottom of

Log Set

Figure 12 - Installing One-Piece Stove

Log Set

Heater Base

CONNECTING TO GAS SUPPLY

WARNING: This appliance

requires a 1/2" NPT (National

Pipe Thread) inlet connection to

the pressure regulator.

WARNING: A qualied service

person must connect heater to gas

supply. Follow all local codes.

CAUTION: Never connect

propane/LP heater directly to the

propane/LP supply. This heater

requires an external regulator

(not supplied). Install the exter-

nal regulator between the heater

and propane/LP supply.

www.desatech.com

113084-01J12

INSTALLATION Continued

WARNING: Never connect

natural gas heater to private (non-

utility) gas wells. This gas is com-

monly known as wellhead gas.

Installation Items Needed

Before installing heater, make sure you have

the items listed below.

• external regulator - propane/LP only (sup-

plied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection *

• sediment trap

• tee joint

• pipe wrench

* A CSA design-certied equipment shutoff

valve with 1/8" NPT tap is an acceptable al-

ternative to test gauge connection. Purchase

the optional CSA design-certied equipment

shutoff valve from your dealer.

The gas inlet connection for the stove heater

is located on the lower right-hand side of stove

when viewed from the front of unit. The gas con-

nection can be made either through the bottom

right side or through the lower back opening as

illustrated in Figure 14. Make sure gas log heater

is secured to stove cavity assembly.

For propane/LP units, installer must supply

an external regulator. The external regulator

will reduce incoming gas pressure. You must

reduce incoming gas pressure to between 11"

and 14" of water. If you do not reduce incom-

ing gas pressure, heater regulator damage

could occur. Install external regulator with

the vent pointing down as shown in Figure

15. Pointing the vent down protects it from

freezing rain or sleet.

CAUTION: Use only new,

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

your local codes. Use pipe of

1/2" diameter or greater to allow

proper gas volume to heater. If

pipe is too small, undue loss of

volume will occur.

Figure 14 - Gas Regulator Location and

Gas Line Access Into Stove Cabinet

Gas Inlet

Connection

Access

Gas Log Heater

Back View

Side View

Figure 15 - External Regulator With Vent

Pointing Down

Back Stove

Panel

Stove Unit Front

Propane/LP

Supply Tank

External

Regulator

with vent

Pointing

Down

Installation must include a equipment shutoff

valve, union and plugged 1/8" NPT tap. Locate

NPT tap within reach for test gauge hook up.

NPT tap must be upstream from heater (see

Figure 16, page 13).

IMPORTANT: Install equipment shutoff valve

in an accessible location. The equipment

shutoff valve is for turning on or shutting off

the gas to the appliances.

Check your building codes for any special

requirements for locating equipment shutoff

valve to replaces.

Apply pipe joint sealant lightly to male threads.

This will prevent excess sealant from going

into pipe. Excess sealant in pipe could result

in clogged heater valves.

WARNING: Use pipe joint

sealant that is resistant to liquid

petroleum (LP) gas.

We recommend that you install a sediment trap

in supply line as shown in Figure 16, page 13.

Locate sediment trap where it is within reach

for cleaning. Install in piping system between

fuel supply and heater. Locate sediment trap

where trapped matter is not likely to freeze.

A sediment trap traps moisture and contami-

nants. This keeps them from going into heater

controls. If sediment trap is not installed or is

installed wrong, heater may not run properly.

www.desatech.com

113084-01J 13

INSTALLATION

Continued

CAUTION: Avoid damage to

regulator. Hold gas regulator

with wrench when connecting it

to gas piping and/or ttings.

* Purchase the optional CSA design-certied

equipment shutoff valve from your dealer.

** Minimum inlet pressure for purpose of input

adjustment.

Figure 16 - Gas Connection

(SVYD18PRA/NRA Series)

3” Min

Sediment Trap

Gas Control

CSA Design-Certied

Equipment Shutoff Valve

With 1/8" NPT Tap*

Approved

Flexible

Gas Hose (if

allowed by

local codes)

Cap Pipe Tee

Nipple Joint

PROPANE/LP

From External

Regulator

(11" W.C. to 14"

W.C. Pressure)

NATURAL

From Gas

Meter (5" W.C.

to 10.5" W.C.

Pressure)

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping

and connections, internal and

external to unit, for leaks after

installing or servicing. Correct

all leaks at once.

WARNING: Never use an

open ame to check for a leak.

Apply a noncorrosive leak detec-

tion uid to all joints. Bubbles

forming show a leak. Correct all

leaks at once.

CAUTION: Make sure exter-

nal regulator has been installed

between propane/LP supply and

heater. See guidelines under Con-

necting to Gas Supply, page 11.

PRESSURE TESTING GAS SUPPLY

PIPING SYSTEM

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPa)

1. Disconnect appliance with its appliance

main gas valve (control valve) and equip-

ment shutoff valve from gas supply piping

system. Pressures in excess of 1/2 psig

will damage heater regulator.

2. Cap off open end of gas pipe where equip-

ment shutoff valve was connected.

3. Pressurize supply piping system by either

opening propane/LP supply tank valve

for propane/LP gas or opening main gas

valve located on or near gas meter for

natural gas or using compressed air.

4. Check all joints of gas supply piping sys-

tem. Apply a noncorrosive leak detection

uid to gas joints. Bubbles forming show

a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment shutoff

valve to gas supply. Check reconnected

ttings for leaks.

Test Pressures Equal To or Less Than 1/2

PSIG (3.5 kPa)

Close equipment shutoff valve (see Figure 17).

2. Pressurize supply piping system by either

opening propane/LP supply tank valve

for propane/LP gas or opening main gas

valve located on or near gas meter for

natural gas or using compressed air.

3. Check all joints from gas meter for natural

or propane/LP supply to equipment shutoff

valve (see Figure 18 or 19, page 14). Apply

a noncorrosive leak detection uid to gas

joints. Bubbles forming show a leak.

4. Correct all leaks at once.

Figure 17 - Equipment Shutoff Valve

Equipment

Shutoff Valve

Closed

Open

www.desatech.com

113084-01J14

INSTALLATION

Continued

PRESSURE TESTING HEATER GAS

CONNECTIONS

1. Open equipment shutoff valve (see Figure

17, page 13).

2. Open main gas valve located on or near

gas meter for natural gas or open pro-

pane/LP supply tank valve.

3. Make sure control knob of heater is in the

OFF position.

Figure 18 - Checking Gas Joints

(Oxford™ Stove Model Shown)

Control Valve Location

Propane/LP

Supply Tank

Equipment Shutoff Valve

Figure 19 - Checking Gas Joints

(Oxford™ Stove Model Shown)

Gas Meter

Equipment

Shutoff Valve

Control Valve Location

OPERATION

4. Check all joints from equipment shutoff

valve to control valve (see Figure 18 or

19). Apply a noncorrosive leak detection

uid to gas joints. Bubbles forming show

a leak.

5. Correct all leaks at once.

6. Light heater (see Operation). Check all

other internal joints for leaks.

7. Turn off heater (see To Turn Off Gas to

Appliance, page 15).

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not fol-

low these instructions exactly,

a re or explosion may result

causing property damage, per-

sonal injury or loss of life.

A. This appliance has a pilot which must

be lighted by hand. When lighting the pi-

lot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around

the appliance area for gas. Be sure to

smell next to the oor because some

gas is heavier than air and will settle

on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the re department.

C. Use only your hand to push in or turn

the gas control knob. Never use tools.

If the knob will not push in or turn by

hand, don’t try to repair it, call a quali-

ed service technician or gas supplier.

Force or attempted repair may result in

a re or explosion.

D. Do not use this appliance if any part

has been under water. Immediately call

a qualied service technician to inspect

the appliance and to replace any part of

the control system and any gas control

which has been under water.

LIGHTING

INSTRUCTIONS

NOTICE: During initial operation

of new heater, burning logs will

give off a paper-burning smell.

Open window to vent smell. This

will only last a few hours.

1. STOP! Read the safety information

above.

2. Make sure equipment shutoff valve is fully

open.

www.desatech.com

113084-01J 15

OPERATION

Continued

3. Set switch to OFF position.

WARNING: Burners will

come on automatically within

one minute when the remote

selector switch is in the ON posi-

tion after the pilot is lit.

4. Press in and turn control knob clockwise

to the OFF position.

5. Wait ve (5) minutes to clear out any gas.

Then smell for gas, including near the

oor. If you smell gas, STOP! Follow “B”

in the safety information, page 14. If you

don’t smell gas, go to the next step.

6. Press in and turn control knob counter-

clockwise to the PILOT position.

Press in control knob for ve (5) seconds

(see step 5).

Note: You may be running this heater for

the rst time after hooking up to gas sup-

ply. If so, the control knob may need to be

pressed in for 30 seconds or more. This will

allow air to bleed from the gas system.

7. With control knob pressed in, press and

release ignitor button. This will light pilot.

The pilot is attached to the front burner

(see Figure 13, page 11). If needed, keep

pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, contact a

qualied service person or gas supplier for

repairs. Until repairs are made, light pilot

with match. To light pilot with match, see

Manual Lighting Procedure, page 16.

8. Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds,

release control knob.

• If control knob does not pop out when

released, contact a qualified service

person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4

through 8.

9. Slightly push in and turn control knob coun-

terclockwise to the ON position.

10. Wait one minute and switch remote se-

lector switch to the ON position to light

burners. Note: AUTO is only functional

when using GWMT1 or GWMS2 optional

accessories.

11. Set ame adjustment knob to any level

between HI and LO.

12. To leave pilot lit and shut off burners only,

turn control knob clockwise to the

PILOT position.

CAUTION: Do not try to ad-

just heating levels by using the

equipment shutoff valve.

WARNING: Make sure the

selector switch is in the OFF

position when you are away from

home for long periods of time.

Heater will come on automati-

cally with selector switch in the

ON position.

AUTO

OFF

Figure 20 - Control Knob and Ignitor

Button Location (Shown as Supplied, No

Control Options)

Ignitor Button

Selector Switch in OFF Position

(Optional Remote Control)

Flame Adjustment Knob

Ignitor

Electrode

Pilot Burner

Figure 21 - Pilot

Thermocouple

Control Knob

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

1. Turn control knob clockwise to the

OFF position.

2. Set selector switch in the OFF position to

keep from draining battery.

3. Close equipment shutoff valve (see Figure

17, page 13).

www.desatech.com

113084-01J16

LOCK

MANU AUTO

ºC/ºF

TEMP

POWER

ROOM

TEMP

SET

TEMP

AUTO

OFF

REMOTE

MANUAL LIGHTING

PROCEDURE

1. Follow steps 1 through 6 under Lighting

Instructions, page 15.

2. Press control knob and light pilot with

match.

3. Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds,

release control knob. Now follow steps 9

through 11 under Lighting Instructions,

page 15.

OPTIONAL HAND-HELD

REMOTE OPERATION

Note: All remote control accessories must

be purchased separately (see Accessories,

page 27). Follow instructions included with

the remote control.

NOTICE: You must light the pilot

before using the hand-held re-

mote control unit. See Lighting

Instructions on page 14.

After lighting, let pilot ame burn for about

one minute. Turn control knob to ON position.

Adjust ame adjustment knob anywhere be-

tween HI and LO. Slide the selector switch to

the REMOTE position (see Figure 22).

Note: The burner may light if hand-held re-

mote was on when selector switch was last

turned off. You can now turn the burner on and

off with the hand-held remote control unit.

IMPORTANT: Do not leave the selector switch

in the REMOTE or ON position when the pilot

is not lit. This will drain the battery.

ON/OFF SERIES (MODEL HRC100)

Hold the control button on the hand-held remote

until burner turns on. Hold the control button

again until burner turns off (see Figure 23).

To Lock press both buttons on hand-held

remote control until light stops ashing. Hand-

held remote control is now locked. If the re

is on it will be turned off automatically. In the

locked state, the light will not light up when

any button is pressed.

To Unlock press both buttons together on hand-

held remote control until the light stops ashing.

The hand-held remote is now unlocked.

Figure 22 - Setting the Remote Selector

Switch, Control Knob and Flame

Adjustment Knob for Remote Operation

Remote Selector Switch

in REMOTE Position

(Optional Remote Control)

Flame Adjustment Knob

Control Knob

in ON Position

THERMOSTAT SERIES (MODEL

HRC200)

The hand-held remote can be operated using

either the manual mode (MANU) or thermo-

static mode (AUTO) (see Figure 24). To select

Fahrenheit/Centigrade mode display, carefully

press the ˚C/˚F mode button with the end of a

paper clip or similar blunt object.

Manual Mode

1. Press the POWER and LOCK buttons

together to turn on the hand-held remote

control.

Figure 23 - On/Off Hand-Held Remote

Control Unit (HR100)

Control Button

Turns Burners

On and Off

Figure 24 - Thermostat Hand-Held

Remote Control Unit (HRC200)

Selects

Auto

Setting

Decreases Room

Temperature in

AUTO Mode

Increases

Room

Temperature in

AUTO Mode

Locks

System to

Prevent

Accidental

Ignition

Digital Display Shows

Temperature and Settings

Turns

Remote On

or Off and

Allows You

to Choose

the Manual

Setting

Turns

Burners

On or Off

OPERATION

Continued

www.desatech.com

113084-01J 17

2. Press the MANU button to turn on the

heater.

3. Press the POWER and LOCK buttons

together to turn off the heater.

Auto (Thermostatic) Mode

1. Press the POWER and LOCK buttons

together to turn on the hand-held remote

control.

2. Press AUTO button to select this mode.

3. Set the desired room temperature by

pressing the TEMP + or - buttons.

4. Press the POWER and LOCK buttons

together to turn off the replace

Note: Do not leave the hand-held remote in

the AUTO mode close to the replace. The

radiant heat from the replace will turn off the

replace. Ideally, place the hand-held remote

in the center of the room facing towards the

replace.

Note: Do not hold the hand-held remote for

a long time. Body temperature will affect its

operation in the AUTO mode.

Safety Features

When away from home for an extended period

of time or as a child safety feature to prevent

INSPECTING BURNERS

Note: The pilot ame on natural gas units will

have a slight curve, but ame should be blue

and have no yellow or orange color.

BURNER PRIMARY AIR HOLES

Air is drawn into the burner through the holes

in the tting at the burner entrance. These

holes may become blocked with dust or lint.

Periodically inspect these holes for any block-

age and clean if needed. Blocked air holes

will create soot.

MAIN BURNER

Periodically inspect all burner ame holes with

the heater running. All slotted burner ame

holes should be open with yellow ame pres-

ent. All round burner ame holes should be

open with a small blue ame present. Some

burner ame holes may become blocked by

debris or rust, with no ame present. If so,

turn off heater and let cool. Remove blockage.

Blocked burner ame holes will create soot.

Pilot Burner

Figure 25 - Correct

Pilot Flame Pattern

(Propane/LP

Shown)

Figure 26 - Incorrect

Pilot Flame Pattern

(Propane/LP Shown)

Thermocouple

OPERATION

Continued

accidental ignition of the replace, the receiver

ON/OFF/REMOTE switch should be in the

OFF position.

Auto Shutoff Feature

If the average room temperature reaches

a range of 82° F (28° C) to 92° F (33° C),

the hand-held remote control will perform a

safety override and shut the replace off. This

feature is not available in the MANU mode.

The receiver continuously receives signals

from the hand-held remote to control the

room temperature. If the hand-held remote

is misplaced, obstructed or for any reason

cannot transmit to the receiver, the receiver

will shut off the replace. This will occur in 8

or more minutes depending upon location of

remote transmitter and strength of batteries.

Key Pad Lock Feature

This feature allows the user to lock/unlock the

keypad on the hand-held remote in the MANU

or AUTO mode to prevent inadvertent op-

eration (i.e. children operating the hand-held

remote control, etc.). The keypad is locked in

either on or off. Press the POWER and LOCK

buttons together to turn the unit on or off.

Check pilot ame pattern and burner ame

patterns often.

PILOT FLAME PATTERN

Figure 25 shows a correct pilot ame pattern.

Figure 26 shows an incorrect pilot ame pat-

tern. The incorrect pilot ame is not heating

the thermocouple. This will cause the thermo-

couple to cool. When the thermocouple cools,

the heater will shut down.

If pilot ame pattern is incorrect, as shown

in Figure 26

• turn heater off (see To Turn Off Gas to Ap-

pliance, page 15

• see Troubleshooting, page 19

www.desatech.com

113084-01J18

CLEANING AND MAINTENANCE

2. Inspect burner, pilot and primary air inlet

holes on injector holder for dust and dirt

(see Figure 27).

3. Blow air through the ports/slots and holes

in the burner.

4. Check injector holder located at end of

burner tube again. Remove any large

particles of dust, dirt, lint or pet hair with

a soft cloth or vacuum cleaner nozzle.

5. Blow air into the primary air holes on the

injector holder.

6. In case any large clumps of dust have now

been pushed into the burner repeat steps

3 and 4.

Clean the pilot assembly also. A yellow tip on

the pilot ame indicates dust and dirt in the

pilot assembly. There is a small pilot air inlet

hole about 2" from where the pilot ame comes

out of the pilot assembly (see Figure 28). With

the unit off, lightly blow air through the air inlet

hole. You may blow through a drinking straw

if compressed air is not available.

Burner Tube

Pilot

Assembly

Pilot Air

Inlet Hole

Ports/Slots

Figure 28 - Pilot Inlet Air Hole

Figure 27 - Injector Holder On Outlet

Burner Tube

Injector

Holder

Primary Air

Inlet Holes

WARNING: Turn off heater

and let cool before cleaning.

CAUTION: You must keep

control areas, burner and circu-

lating air passageways of heater

clean. Inspect these areas of

heater before each use. Have

heater inspected yearly by a

qualied service person. Heater

may need more frequent clean-

ing due to excessive lint from

carpeting, pet hair, bedding

material, etc.

WARNING: Failure to keep

the primary air opening(s) of

the burner(s) clean may result in

sooting and property damage.

BURNER INJECTOR HOLDER AND

PILOT AIR INLET HOLE

The primary air inlet holes allow the proper

amount of air to mix with the gas. This pro-

vides a clean burning flame. Keep these

holes clear of dust, dirt, lint and pet hair.

Clean these air inlet holes prior to each

heating season. Blocked air holes will create

soot. We recommend that you clean the unit

every three months during operation and

have heater inspected yearly by a qualied

service person.

We also recommend that you keep the burner

tube and pilot assembly clean and free of dust

and dirt. To clean these parts we recommend

using compressed air no greater than 30 PSI.

Your local computer store, hardware store or

home center may carry compressed air in a

can. If using compressed air in a can, please

follow the directions on the can. If you don’t

follow directions on the can, you could dam-

age the pilot assembly. Note: Removing the

rear panel (Figure 5, page 9) and top grate(s)

of your stove will make cleaning easier.

1. Shut off unit, including pilot. Allow unit to

cool for at least thirty minutes.

www.desatech.com

113084-01J 19

TROUBLESHOOTING

WARNING: Turn off heater and let cool before servicing. Only a

qualied service person should service and repair heater.

CAUTION: Never use a wire, needle or similar object to clean

ODS/pilot. This can damage ODS/pilot unit.

Note: All troubleshooting items are listed in order of operation.

POSSIBLE CAUSE

1. Ignitor electrode not con-

nected to ignitor cable

2. Ignitor cable pinched or

wet

3. Broken ignitor cable

4. Bad piezo ignitor

5. Ignitor electrode broken

6. Ignitor electrode positioned

wrong

Gas supply turned off or equip-

ment shutoff valve closed

2. Control knob not in PILOT

position

3. Control knob not pressed in

while in PILOT position

4. Air in gas lines when in-

stalled

5. ODS/pilot is clogged

6. Gas regulator setting is not

correct

7. Depleted gas supply (pro-

pane/LP only)

1. Control knob not fully

pressed in

2. Control knob not pressed in

long enough

3. Equipment shutoff valve not

fully open

4. Pilot flame not touching

thermocouple, which allows

thermocouple to cool, caus-

ing pilot ame to go out. This

problem could be caused by

one or both of the following:

A) Low gas pressure

B) Dirty or partially clogged

ODS/pilot

5. Thermocouple connection

loose at control valve

6. Thermocouple damaged

7. Control valve damaged

REMEDY

1. Reconnect ignitor cable

2. Free ignitor cable if pinched

by any metal or tubing.

Keep ignitor cable dry

3. Replace ignitor cable

4. Replace piezo ignitor

5. Replace pilot assembly

6. Replace pilot assembly

1. Turn on gas supply or open

equipment shutoff valve

2. Turn control knob to PILOT

position

3. Press in control knob while

in PILOT position

4. Continue holding down con-

trol knob. Repeat igniting op-

eration until air is removed

Clean ODS/pilot (see Cleaning

and Maintenance, page 18) or

replace ODS/pilot assembly

6. Replace gas control

7. Contact local propane/LP

gas company

1. Press in control knob fully

2. After ODS/pilot lights, keep

control knob pressed in 30

seconds

3. Fully open equipment shut-

off valve

4. A) Contact local propane/

LP or natural gas com-

pany

B) Clean ODS/pilot (see

Cleaning and Maintenance,

page 18) or replace ODS/

pilot assembly

5. Hand tighten until snug,

then tighten 1/4 turn more

6. Replace pilot assembly

7. Replace control valve

OBSERVED PROBLEM

When ignitor button is

pressed, there is no spark

at ODS/pilot

When ignitor button is

pressed, there is spark at

ODS/pilot but no ignition

ODS/pilot lights but ame

goes out when control knob

is released

www.desatech.com

113084-01J20

POSSIBLE CAUSE

1. Burner orice clogged

2. Inlet gas pressure is too

low

Thermopile leads disconnect-

ed or improperly connected

4. Burners will not come on in

remote position

1. Manifold pressure is too

low

2. Burner orice clogged

1. Burner orice is clogged or

damaged

2. Damaged burner

3. Gas regulator defective

1. Not enough air

2. Gas regulator defective

Residues from manufacturing

processes and logs curing

1. Not enough combustion/

ventilation air

1. Turning control knob to HI

position when burner is

cold

2. Air in gas line

3. Air passageways on heater

blocked

4. Dirty or partially clogged

burner orice

1. Improper log placement

2. Drafts or other air currents

affecting ame pattern

3. Air holes at burner inlet

blocked

4. B u r n e r f l a m e h o l e s

blocked

REMEDY

1. Clean burner (see Cleaning

and Maintenance, page 18)

or replace burner orice

2. Contact local propane/LP

or natural gas company

3. Reconnect leads (see Wir-

ing Diagram, page 26)

4. Replace battery in transmit-

ter and hand-held remote

1. Contact local propane/LP

or natural gas company

2. Clean burner (see Cleaning

and Maintenance, page 18)

or replace burner orice

1. Clean burner (see Cleaning

and Maintenance, page 18)

or replace burner orice

2. Replace damaged burner

3. Replace gas control

1. Check burner for dirt and

debris. If found, clean

burner (see Cleaning and

Maintenance, page 18)

2. Replace gas control

3. Problem will stop after a few

hours of operation

1. Refer to Air for Combustion

and Ventilation require-

ments (page 5)

1. Turn control knob to LO

position and let warm up

for a minute

Operate burner until air is

removed from line. Have gas

line checked by local propane/

LP or natural gas company

Observe minimum installation

clearances (see page 8)

4. Clean burner (see Cleaning

and Maintenance, page 18)

or replace burner orice

1. Properly locate logs (see

Installing Gas Log Into

Stove, page 11)

2. Eliminate source of drafts

around heater

3. Clean out air holes at burn-

er inlet. Periodically repeat

as needed

4. Remove blockage or re-

place burner

OBSERVED PROBLEM

Burner does not light after

ODS/pilot is lit

Delayed ignition burner

Burner backfiring during

combustion

Slight smoke or odor during

initial operation

Moisture/condensation no-

ticed on windows

Heater produces a whistling

noise when burner is lit

Dark residue on logs or inside

of replace

TROUBLESHOOTING

Continued

Page is loading ...

Desa Tech CISAW Owner's manual

Brand: Desa Tech

Model: CISAW

Category: Fireplaces

Type: Owner's manual

Download PDF

report

Desa Tech CISAW Owner's manual

Desa Tech CISAW Owner's manual

Related papers

Other documents