OWNER’S MANUAL
FORM: OM-632 191 281F
2008−12
No. 28 (043 861), No. 32 (194 997) And
No. 37 (195 282) Running Gear
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
Beware of electric shock from wiring. Disconnect input
power before installing this kit. Reinstall all panels and
covers.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Cylinders contain gas under high pressure and can ex-
plode if damaged. Never let a welding electrode touch
any cylinder. Always secure cylinder to running gear, wall,
or other stationary support.
Falling equipment can cause injury and unit damage.
Never put any body part under unit while lifting. Lifting
forks must extend out opposite side of base. Lift unit
using proper equipment.
Tools Needed:
3/8, 9/16 in
Optional
802 192 / 802 191
Part
No.
Item
No.
Description (Qty)
1 191 166 Handle, LH (1) (No. 28 RG)
1 204 295 Handle, LH (1) (No. 32 RG)
2 108 942 Screw, 1/4-20 x 1-1/4 (4)
3 191 164 Bottle Support (1)
4 Existing Screw, 1/4-20 x 1/2slffmg
5 168 663 Hook Spring, Snap (3)
6 602 387 Chain (2)
7 191 158 Bottle Tray (1)
8 121 614 Retaining Ring (2)
9 163 463 Wheel, 10 in (2)
10 602 250 Washer, 3/4 flat (4)
11 191 167 Axle (1)
12 168 247 Caster, Swivel 5 in (2)
13 191 163 Caster Mounting Bracket (1)
14 167 788 Nut, 3/8-16 wshr (8)
15 601 965 Screw, 3/8-16 x 1 (12)
16 191 165 Handle, RH (1) (No. 28 RG)
16 204 296 Handle, RH (1) (No. 32 RG)
Be sure to provide Model when ordering
replacement parts.
8
9
10
Remove paint from axle grooves (11)
before installing retaining rings (8).
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Route hoses and
cords as shown to
prevent damage
and shock hazards.
11
Remove and discard
the four end caps and
eight screws before
installing caster bracket
(13) and bottle tray (7).
Remove and retain existing hardware
(4) before installing handles (1) and
bottle support (3).
Use hardware re-
tained from handle
installation to install
caster mounting
bracket (13) to base
of power source.
Use the four supplied screws (15) to
install bottle tray (7) to the welding
power source base
15
No. 28 And No. 32 Running Gear
OM-632 Page 2
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
Beware of electric shock from wiring. Disconnect input
power before installing this kit. Reinstall all panels and
covers.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Cylinders contain gas under high pressure and can ex-
plode if damaged. Never let a welding electrode touch
any cylinder. Always secure cylinder to running gear, wall,
or other stationary support.
Falling equipment can cause injury and unit damage.
Never put any body part under unit while lifting. Lifting
forks must extend out opposite side of base. Lift unit
using proper equipment.
Tools Needed:
3/8, 9/16 in
Optional
Part
No.
Item
No.
Description (Qty)
1 242 337 Handle (2)
2 +215 928 Bottle Support (1)
3 168 663 Hook Spring, Snap (3)
4 210 224 Chain (2)
5 191 158 Bottle Tray (1)
6 121 614 Retaining Ring (2)
7 602 250 Washer, 3/4 flat (4)
8 163 463 Wheel, 10 in (2)
9 191 167 Axle (1)
10 168 247 Caster, Swivel 5 in (2)
11 191 163 Caster Mounting Bracket (1)
13 217 140 Label, warning cyl may exp (Eng/Fr) (1)
13 200 285 Label, warning cyl may exp
(200/230/460 volt models only) (1)
Be sure to provide Model when ordering replacement parts.
Remove paint from axle
grooves before installing re-
taining rings.
Remove and discard the four end caps,
but retain the existing hardware and use it
to install the caster bracket.
No. 37 Running Gear
9
6
7
8
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
803 726-A / 803 725-D
1
2
3
4
5
6
8
9
10
11
13
-
1
-
2
Miller RUNNING GEAR NO. 32 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller KF000000 Owner's manual
-
Miller BLUE RUNNER CART (043965) Owner's manual
-
-
-
-
-
Miller KF000000 Owner's manual
-
-
-
Miller Syncrowave 250 DX Owner's manual