CHAPTER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
3
INDEX
Introduction
General points on delivery
Guarantee
Safety Measures
Technical Data
Setting up and Installation
Control Description
Table of Programmes
Selection
Detergent drawer
The Product
Washing
Drying
Automatic washing/drying cycle
Cleaning and routine maintenance
Faults Search
2
INTRODUCTION
Thank you for buying this high quality appliance from us
We would like to congratulate you on choosing this
appliance, and hope you find it to be an attractive and
beneficial addition to your home.
This handbook is designed to help you through each step of
owning your new appliance, from installation, to use.
Please read through all of this guide carefully before you
start using your appliance, as we have endeavoured to
answer as many questions as possible, and provide you with
as much support as we can.
If, however, you should find something missing, or not
covered, please contact the Belling Customer Care team
who will be only too happy to assist you on:
0871 22 22 503
In addition you could always try the website for frequently
asked questions and more Customer Care information.
Our policy is one of constant development and
improvement,therefore we cannot guarantee the strict
accuracy of all of our illustrations and specifications -
changes may have been made subsequent to publishing.
CUSTOMER CARE INFORMATION
If you should experience problems while operating the
appliance please refer to Chapter 15 – Faults search. If the
answer to the problem is not covered please call the
Customer Care Centre number listed above.
Your appliance is covered by a 12 month manufacturers
guarantee. If you experience problems within the first year
from the date of purchase a service engineer will be sent to
resolve the problem without charge. In order to prove the
age of the product please retain your purchase receipt.
CHAPTER 2
GUARANTEE
The appliance is supplied with a manufacturers 12 month
guarantee. Please retain your purchase receipt.
This should be kept in a safe place and presented to the
engineer if a service call is required.
5
4
C
B
CHAPTER 1
GENERAL POINTS ON DELIVERY
On delivery, check that the following are included with the
machine:
A) INSTRUCTION MANUAL
B) PLUGS
C) BEND FOR OUTLET TUBE
D) LIQUID DETERGENT OR LIQUID BLEACH
COMPARTMENT (CONTAINER)
KEEP THEM IN A SAFE PLACE
Check that the machine has not incurred damage during
transport. If this is the case, contact your nearest Technical
Assistance Centre.
D
A
76
CHAPTER 3
SAFETY MEASURES
IMPORTANT:
FOR ALL CLEANING AND MAINTENANCE WORK
● Remove the plug
● Turn off the water inlet tap.
● All Belling appliances are earthed. Ensure that the main
electricity circuit is earthed. Contact a qualified electrician if
this is not the case.
Appliance complies with European Directives
73/23/EEC and 89/336/EEC, replaced by 2006/95/EC and
2004/108/EC, and subsequent amendments.
● Do not touch the appliance with wet or damp hands or
feet.
WARNING: DURING THE WASHING CYCLE, THE WATER
CAN REACH A TEMPERATURE OF 90°C.
● Before opening the washing machine door, ensure that
there is no water in the drum.
● Do not use extension leads or multiple plugs.
● This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
● Do not pull the mains lead or the appliance itself to
remove the plug from the socket.
● Do not leave the appliance exposed to atmospheric
conditions (rain, sun etc.)
● In the case of removal,never lift the appliance by the
knobs or detergent drawer.
● During transportation do not lean the door against the
trolley.
Important!
When the appliance location is on carpet floors, attention
must be paid so as to ensure that there is no obstruction to
the bottom vents.
● Lift the appliance in pairs as illustrated in the diagram.
● In the case of failure and/or incorrect operation,turn the
washing machine off,close the water inlet tap and do not
tamper with the appliance. Contact a Technical Assistance
Centre for any repairs and ask for original spare parts.
Avoidance of these norms may compromise the safety of
the appliance.
● Should the supply cord (mains cable) be damaged,this is
to be replaced by a specific cable available from the after
sales service centre.
9
CHAPTER 5
SETTING UP INSTALLATION
Move the machine near its permanent position without the
packaging base.
Cut tube-holding straps.
Remove the 3 fixing screws marked (A) and remove the 3
spacers marked (B)
Remove the screw (C).
A spacer will fall inside the machine.
By tilting the machine, remove the above mentioned spacer.
Stop the holes using the plugs that you will find inside the
bag containing the instruction booklet.
WARNING:
DO NOT LEAVE THE PACKAGING IN THE REACH OF
CHILDREN AS IT IS A POTENTIAL SOURCE OF DANGER.
8
CHAPTER 4
MAXIMUM WASH LOAD DRY
POWER INPUT
ENERGY CONSUMPTION (PROG. 90°C)
FUSE RATING
SPIN
WATER PRESSURE
SUPPLY VOLTAGE
TECHNICAL DATA
kg
2150
1,8
13
230
W
kWh
A
MPa
V
82 cm
60 cm
54 cm
64
1400
DRYING
r.p.m.
WASHING
min. 0,05
max. 0,8
11
Use the 4 feet to level the machine with the floor:
a) Turn the nut clockwise to release the screw adjuster of the
foot.
b) Rotate foot to raise or lower it until it stands firmly on the
ground.
c) Lock the foot in position by turning the nut anti-clockwise
until it comes up against the bottom of the machine.
Ensure that the knob is on the “OFF” position and the load
door is closed
Insert the plug.
After installation, the appliance must be positioned so that
the plug is accessible.
A
B
C
10
min 50 cm
max 85 cm
+2,6 mt max
max 100 cm
min 4 cm
Fix the sheet of corrugated material on the bottom as shown
in picture.
Connect the fill hose to the tap.
The appliance must be connected to the water mains using
new hose-sets.The old hose-sets should not be reused.
IMPORTANT:
DO NOT TURN THE TAP ON AT THIS TIME.
Position the washing machine next to the wall. Hook the
outlet tube to the edge of the sink paying attention that
there are no bends or restrictions along the tube.
It is better to connect the discharge hose to a fixed outlet of
a diameter greater than that of the outlet tube and at a
height of min. 50 cm. If is necessary to use the plastic sleeve
supplied.
The appliance must not be installed behind a lockable door,
a sliding door or a door with a hinge on the opposite side to
that of the washer dryer.
Please refer to diagrams below for various installation
options.
13
CHAPTER 6
CONTROLS
12
REMO
VING THE PLUG:
If your appliance has a non-rewireable moulded plug and you should wish to re-route the
mains cable through partitions, units etc., please ensure that either:
the plug is replaced by a fused 13 ampere re-wireable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in
compliance with BS 5733) which is accessible without moving the appliance.
DISPOSING OF THE PLUG:
Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be
accidentally inserted into a socket.
INSTRUCTIONS FOR CONNECTING CABLE TO
AN ALTERNATIVE
PLUG:
Important: the wires in the mains lead are coloured in accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live
As the colours of the wires in the lead may not correspond with the coloured markings
identifyng the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E or or coloured Green or Green &
Yellow. Connect Brown wire to terminal marked L or coloured Red.
Connect Blue wire to terminal marked N or coloured Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse either in the plug or
adaptor or at the distribution board. If you are in any doubt the electrical supply to your
machine, consult a qualified electrician before use.
HOW TO CONNECT AN ALTERNATIVE PLUG:
The wires in this mains lead are coloured in accordance with the following code:
BLUE NEUTRAL(N)
BROWN LIVE(L)
GREEN&YELLOW EARTH(E)
DISPOSING OF THE APPLIANCE:
When disposing of the appliance please remove the plug by
cutting the mains cable as close as possible to the plug body
and dispose of it as described above.
R
D
Q
C
E
MG
FB
H
ILNOP A
Door open button
Programme selector with “OFF” position
"Door Security" indicator light
"Delay Start" button
"Time countdown system" and “Delay Start” indicator lights
"Spin Selection" button
Spin speed indicator light
"Super Rapid" button
"Extra Rinse" button
"Drying Selection" button
Drying programme indicators
"Cold Wash" button
“Crease Guard” button
"Start/Pause" button
Buttons indicator light
Detergent drawer
A
B
C
D
E
F
G
H
I
L
M
N
O
P
Q
R
DELAY START BUTTON
Appliance start time can be set with this button, delaying the
start by 3, 6 or 9 hours.
Proceed as follows to set a delayed start:
Select a programme (“STOP” indicator light blinks)
Press "Delay Start" button (each time the button is pressed the
start will be delayed by 3, 6 or 9 hours respectively and the
corresponding light will blink).
Press "Start/Pause" to commence the Delay Start operation
(the indicator light associated with the selected Delay Start
time stops blinking and remains ON).
At the end of the required time delay the programme will
start.
To cancel the Delay Start function :
press the "Delay Start" button until the indicator lights will be
off (The "STOP" light blinks) and the programme can be
started manually using the "Start/Pause" button or switch off
the appliance by turning the programme selector to "OFF"
position.
WARNING: IF THERE IS ANY BREAK IN THE POWER
SUPPLY WHILE THE MACHINE IS OPERATING, A SPECIAL
MEMORY STORES THE SELECTED PROGRAMME AND,
WHEN THE POWER IS RESTORED, IT CONTINUES WHERE IT
LEFT OFF.
TIME COUNTDOWN SYSTEM INDICATOR LIGHTS
In order to better manage your time, this washing machine
features an indicator light system that keeps you constantly
informed on the remaining cycle time.
Indicator light 90:
Remaining time above 60 minutes
Indicator light 60:
Remaining time less than 60 minutes
Indicator light 30:
Remaining time less than 30 minutes
Indicator light 15:
Remaining time less than 15 minutes
Indicator light Stop:
End of the programme.
15
D
E
14
A
1 min.
C
DESCRIPTION OF CONTROL
DOOR OPEN BUTTON
IMPORTANT:
A SPECIAL SAFETY DEVICE PREVENTS THE DOOR FROM
OPENING AT THE END OF THE WASH/SPIN CYCLE. AT THE
END OF THE SPIN PHASE WAIT UP TO 1 MINUTE BEFORE
OPENING THE DOOR.
PROGRAMME SELECTOR WITH OFF POSITION
ROTATES IN BOTH DIRECTIONS.
THE MACHINE IS TURNED ON BY SELECTING A
PROGRAMME VIA THE PROGRAMME SELECTOR.
THIS STATUS WILL BE INDICATED BY THE STOP
INDICATOR LIGHT FLASHING, THIS LIGHT WILL
CONTINUE TO FLASH UNTIL THE MACHINE HAS STARTED
OR THE MACHINE IS RETURNED TO THE OFF POSITION.
Press the "Start/Pause" button to start the selected cycle.
The programme carries out with the programme selector
stationary on the selected programme till cycle ends.
Switch off the washing machine by turning the selector to OFF.
NOTE:
THE PROGRAMME SELECTOR MUST BE RETURN TO THE
OFF POSITION AT THE END OF EACH CYCLE OR WHEN
STARTING A SUBSEQUENT WASH CYCLE PRIOR TO THE
NEXT PROGRAMME BEING SELECTED AND STARTED.
DOOR LOCKED INDICATOR
The “Door Locked” indicator light is illuminated when the door
is fully closed and the machine is ON.
When START is pressed on the machine with the door closed
the indicator will flash momentarily and then illuminate.
If the door is not closed the indicator will continue to flash.
A special safety device prevents the door from being opened
immediately after the end of the cycle.Wait for 1 minute after
the wash cycle has finished and the Door Locked light has
gone out before opening the door. At the end of cycle turn
the programme selector to OFF.
B
17
L
DRYING SELECTION BUTTON
With the programme selector not in the OFF position, press
the button to select the required drying programme; an
indicator will light to display the drying result selected each
time you press the button.
To cancel the selection before the start of a drying
programme, press the button repeatedly until the indicators
go out or return the programme selector to the OFF position.
To cancel the cycle during the drying phase, hold the button
down for 2 seconds until the cooling indicator lights up; given
the high temperature inside the drum, we recommend that
you allow the dryer to complete the cool down period
before returning the programme selector to the OFF position
and removing the laundry.
DRYING PROGRAMME INDICATORS
The indicators display the type of programme and/or drying
time:
A
utomatic Programmes: By selecting one of these 3
automatic programmes, the washer-dryer will calculate the
time needed for drying and the residual dampness required,
according to the load and drying type selected.
After pressing the START button, one of the indicators will light
to display the drying time remaining.
= Extra dry drying programme (recommended for
towels, bathrobes and bulky loads)
= Cupboard dry drying programme
= Iron dry drying programme
USEFUL TIPS:
The 30 minute drying programme is recommended for small
loads (less than 1 kg) or slightly damp loads.
Your washer-dryer ends the cycle automatically when it
reaches the drying level selected.
For the correct operation of the appliance, it is preferable
not to interrupt the drying phase unless it is really necessary.
Timed programmes:
120 minutes – 90 minutes – 60 minutes – 30 minutes:
Dual function indicators:
If one of the 3 automatic drying programmes is selected, the
indicators display the drying time remaining
They may be used to select timed drying programmes.
Cool down phase :
Switched on during the final cool down period, in the last 10
minutes of each drying phase.
COLD WASH BUTTON
By pressing this button it is possible to transform every
programme into a cold washing one,without modifying
other characteristics (water level,times, rythmes, etc...).
Curtains, small carpets, man made delicate fabrics, non
coulor fast garments can be safely washed thanks to this
new device.
16
SPIN SELECTION BUTTON
The spin cycle is very important to remove as much water as
possible from the laundry without damaging the fabrics.You
can adjust the spin speed of the machine to suit your needs.
By pressing this button, it is possible to reduce the maximum
speed, and if you wish, the spin cycle can be cancelled.To
reactivate the spin cycle press the button until you reach the
spin speed you would like to set. To prevent damage to the
fabrics, it is not possible to increase the speed over that
which is automatically suitable during the selection of the
program.
It is possible to modify the spin speed without to pausing the
machine.
NOTE:
THE MACHINE IS FITTED WITH A SPECIAL ELECTRONIC
DEVICE, WHICH PREVENTS THE SPIN CYCLE SHOULD
THE LOAD BE UNBALANCED. THIS REDUCES THE NOISE
AND VIBRATION IN THE MACHINE AND SO PROLONGS
THE LIFE OF YOUR MACHINE.
SPIN SPEED INDICATOR LIGHT
When you set a program,the maximum possible spin speed
will be automatically shown by the relevant indicator light.
Choosing a smaller spin speed by the appropriate button,
the relevant indicator light will go on.
The option buttons should be selected before pressing the
START button
SUPER RAPID BUTTON
By pushing this button the time of the wash programme is
reduced to a maximum of 50 minutes depending on the
programme and the temperature selected.The super rapid
button can be used for washing loads of 1 to 6 kg.
(This button can be utilised only on cottons and synthetic
programmes).
EXTRA RINSE BUTTON
The extra rinse program ensures clothing is thoroughly rinsed
and free of detergents. The program combines a unique
drum action with a number of additional rinses to achieve a
high degree of detergent free clothing.
The extra rinse program is ideal for people with sensitive skin
who require minimum detergent residue to avoid irritation or
allergies. It is advisable to use this program to clean
children’s clothing, towels and heavily soiled items where a
lot of detergent has been used and is retained in the fibres.
Note: - This program is not suitable for woollen garments and
is not available during the wool program.
G
F
H
I
M
N
19
Q
18
O
P
CREASE GUARD BUTTON
The Crease Guard function minimizes creases as much as
possible with a uniquely designed anti-crease system that is
tailored to specific fabrics.
MIXED FABRICS - the water is gradually cooled throughout
the final two rinses with no spinning and then a delicate spin
assures the maximum relaxation of the fabrics.
DELICATE FABRICS – final two rinses with no spinning and then
the fabrics are left in water until it is time to unload. When you
are ready to unload, press the "Crease Guard" button – this
will drain.
WOLLENS/HAND WASH – after the final rinse the fabrics are
left in water until it is time to unload and the button indicator
blinking.
When you are ready to unload, press the "Crease Guard"
button, this will drain and spin ready for emptying.
If you do not want to spin the clothes and activate drain
only:
- Turn the programme selector to the "OFF" position;
- Select programme drain only ;
- Switch on the appliance again by pressing the
"Start/Pause" button.
START BUTTON
When a programme is selected, wait for the “STOP” indicator
light to flash before pressing the START button.
Press to start the selected cycle (according to the selected
cycle one indicator lights will go on) .
NOTE: WHEN THE START BUTTON HAS BEEN PRESSED THE
APPLIANCE CAN TAKE A FEW SECONDS BEFORE IT
STARTS WORKING.
CHANGING THE SETTINGS AFTER THE PROGRAMMES HAS
STARTED (PAUSE)
The programme may be paused at any time during the wash
cycle by holding down the "Start/Pause" button for about
two seconds.When the machine is in the paused mode, the
indicator light "Time countdown",Spin Speed and option
buttons will flash. To restart the programme, press the START
button once again.
If you wish to add or remove items during washing, wait 1
minute until the safety device unlocks the door.
When you have carried out the manoeuvre, close the door,
press START button and the appliance will continue working
from where it left off.
CANCELLING THE PROGRAMME
To cancel the programme,set the selector to the OFF position.
Select a different programme.
Re-set the programme selector to the OFF position.
BUTTON INDICATOR LIGHT
These light up when the relevant buttons are pressed.
If an option is selected that is not compatible with the
selected programme then the light on the button first flashes
and then goes off.
20 21
WEIGHT
MAX
kg
6
6
6
6
6
3
3
3
3
-
-
-
1,5
1
1
2
3
6
6
4
3
TEMP.
°C
90°
60°
60°
40°
30°
60°
60°
50°
40°
-
-
-
40°
30°
30°
40°
60°
40°
40°
-
-
**
*
*
*
*
II I
●●
●●●
●●
●●
●●
●●●
●●
●●
●●
●
●●
●●
●●
●●
●●
●●
●●
*
*
*
*
*
*
*
*
*
*
PROGRAMME
SELECTOR ON:
Please read these notes
When washing heavily soiled laundry it is recommended the load is reduced to 4 kg maximum.
Information for the test laboratories
(Ref. EN 50229 Standards)
Washing
Use the programme **
Drying
First drying with 4kg (the load consist: pillowcases and hand-towels) selecting the cotton
drying programme ( ) cupboard dry ( ).
Second drying with 2kg (the load consist: 2 sheets and hand towels) selecting the cotton
drying programme ( ) 90 minutes
(90’).
The spin speed may also be reduced, to match any guidelines suggested on the fabric label, or for
very delicate fabrics cancel the spin completely this option is available with a spin speed button.
* Programmes for automatic drying.
TABLE OF PROGRAMMES
Resistant fabrics
Cotton, linen
Cotton, mixed
resistant
Cotton, mixed
Mixed fabrics and synthetics
Mixed, resistant
Cotton, mixed fabrics,
synthetics
Synthetics (nylon,
perlon), mixed cotton
Very delicate fabrics
CHARGE DETERGENT
PROGRAM FOR:
SpecialS
Whites
Whites with
Prewash
Fast coloureds
Non fast coloureds
Delicates
Fast coloureds with
Prewash
Fast coloureds
Synthetics
Non fast coloureds
Rinse
Fast spin
Drain only
Delicates
“MACHINE
WASHABLE”
woollens
Hand wash
Rapid 30 minute
Resistant Fabrics
Resistant Fabrics
“All 40°C”
system programme
Cotton - Drying
Mixed - Drying
CHAPTER 7
*
23
30 MINUTE RAPID PROGRAMME
The 30 minute rapid programme allows a complete washing
cycle to be carried out in approximately 30 minutes, with up
to a maximum load of 2 kg and a temperature of 40°C.
When selecting the "30 minute rapid" programme, please
note that we recommend you use only 20% of the
recommended quantities shown on the detergent pack.
“A” WASH 59 '
This specially designed programme maintains the high quality
wash performance identified with the “A” rating whilst greatly
reducing the wash time. The programme is designed for a
maximum load of 3 kg with a temperature of 60°C and
concludes with 2 rinses and a high speed spin sequence.
AA SPECIAL PROGRAMME at 40°C
This special programme has been studied to allow you to
obtain the best washing performance, even at full load, as
the 60°C Cotton programme (the normative cycle),but with
the advantage of an energy saving due to 40°C
temperature,instead of 60°C.
The length of this programme lasts almost the 3 hours.
“ALL 40°C” PROGRAMME
This is an exclusive system and involves 2 great advantages
for the consumer:
• to be able to wash together different type of fabrics (e.g.
cotton + synthetic etc…) FAST COLOUREDS;
•to wash with a considerable energy saving.
The “All 40°C” is an eco friendly programme that has low
energy consumption (850W/h). The programme achieves this
by using a low water temperature combined with periods of
inactive soaking and short periods of drum cycling over a
period of three hours.
Important:
•the first washing of new coloureds fabrics must be done
separately;
• in every case, never mix NON-FAST COLOUREDS fabrics.
Drying
Note: Dispensers used for concentrated powders and liquid
detergents must be removed from the drum before
commencing the tumble drying programmes.
The drum changes direction during the drying cycle to
prevent the laundry from tangling and hence produce even
drying. Cool air is used during the last ten minutes of the
drying cycle to minimise creasing.
High Heat
High temperature drying programme for Cottons and linen
items, always refer to the care label
Low Heat
Low temperature drying programme for synthetics and mixed
fibres, always refer to the care label.
22
CHAPTER 8
SELECTION
For the various types of fabrics and various degrees of dirt the
washing machine has different programme bands according to:
wash cycle, temperature and lenght of cycle (see table of
washing cycle programmes).
RESISTANTS FABRICS
The Cotton programme is designed for maximum washing and
rinsing efficiency.With spin cycles in between, the programme
guarantees the laundry is rinsed perfectly.The final spin cycle
ensures laundry is spun dry as much as possible up to the
maximum speed.
The Cotton programme includes a Prewash cycle.This option is
particularly useful for really dirty loads and can be used
independently of the main wash programme.Additional
detergent for the Prewash part of the programme should be
added to the first compartment of the soap drawer labelled "I"
(please refer to the section of this manual entitled “Detergent”).
We recommend you use only 20% of the quantity used for the
main wash programme.
MIXED AND SYNTHETIC FABRICS
The main wash and the rinse gives best results thanks to the
rotation rhythms of the drum and to the water levels.
A gentle spin will mean that the fabrics become less creased.
SPECIAL “RINSE” PROGRAMME
This programme carries out three rinses with a intermediate spin
(which can be reduced or excluded by using the correct button). It
can be used for rinsing any type of fabric,eg.use after hand-washing.
SPECIAL “SPIN” PROGRAMME
Programme “SPIN” carries out a maximum spin (which can be
reduced by using the correct button).
DRAIN ONLY
This programme drains out the water.
SPECIAL DELICATE FIBRES
This is a new wash cycle which alternates washing and soaking
and is particularly recommended for very delicate fabrics such as
Pure Machine Washable Wool. The wash cycle and rinses are
carried out with high water levels to ensure best results.
WOOLMARK PROGRAMME
The special cycle, certified by WOOLMARK, enables to
thoroughly wash garments without damaging them.The cycle
comprises of alternate periods of activity and pauses.The
programme has a maximum temperature of 30° and
concludes with 3 rinses and a short spin.
SPECIAL “HAND WASH”
This washing machine also has a gentle Hand Wash
programme cycle.This programme allows a complete
washing cycle for garments specified as “Hand Wash only” on
the fabric care label. The programme has a temperature of
30°C and concludes with 3 rinses and a slow spin.
25
CHAPTER 10
THE PRODUCT
IMPORTANT:
When washing heavy rugs, bed spreads and other heavy
articles, it is advisable not to spin.
Do not dry wool,items with special padding delicate silk
irems; rubber, plastic, including some types of plastic
poppers on duvet covers and foam plastic items are not
suitable for tumble drying.
To be machine-washed,woollen garments and other articles
in wool must bear the “Machine Washable Label”.
IMPORTANT:
When sorting articles ensure that:
- there are no metal objects in the washing (e.g.
brooches, safety pins, pins, coins etc.).
- cushion covers are buttoned, zips and hooks are
closed, loose belts and long tapes on dressing gowns
are knotted.
- runners from curtains are removed.
- attention is paid to garment labels.
- when sorting, any tough stains should be removed prior
to washing using stain removers only recommended on
label.
25
CHAPTER 9
DETERGENT DRAWER
The detergent draw is split into 3 compartments:
- the compartment labelled "I" is for prewash detergent;
- the compartment labelled “✿✿” is for special additives,
fabric softeners, fragrances, starch, brighteners etc;
- the compartment labelled "II" is for main wash detergent.
If liquid detergents are used, please insert the special
container supplied into the compartment marked “II” in the
detergent drawer.This ensures that the liquid detergent
enters the drum at the right stage of the wash cycle.
This special container must be inserted when using the
“RINSE” program as a BLEACHING cycle.
NOTE: SOME DETERGENTS ARE DIFFICULT TO REMOVE.
FOR THESE, WE RECOMMEND YOU USE THE SPECIAL
DISPENSER WHICH IS PLACED IN THE DRUM.
NOTE: ONLY PUT LIQUID PRODUCTS IN THE
COMPARTMENT LABELLED “
✿✿”. THE MACHINE IS
PROGRAMMED TO AUTOMATICALLY TAKE UP
ADDITIVES DURING THE FINAL RINSE STAGE FOR ALL
WASH CYCLES.
27
WASHING
VARIABLE CAPACITY
This washing machine automatically adapts the level of the water
to the type and quantity of washing.In this way it is also possible to
obtain a “personalized” wash from an energy saving point of view.
This system gives a decrease in energy consumption and a
sensible reduction in washing times.
EXAMPLE:
A net bag should be used for particularly delicate fabrics.
Let us suppose that the washing consists of HEAVILY SOILED
COTTON (tough stains should be removed with suitable stain
removal).
It is advisable not to wash a load made up entirely of articles
in towelling fabric which absorb a lot of water and become
too heavy.
● Open the detergent drawer .
● Put 120 g in the main wash compartment marked II.
● Put 50 ml of the desired additive in the additives
compartment
✿✿
.
● Close the detergent drawer .
CHAPTER 11
CUSTOMER AWARENESS
A guide environmentally friendly and economic use of your
appliance.
MAXIMISE THE LOAD SIZE
Achieve the best use of energy, water, detergent and time by
using the recommended maximum load size.
Save up to 50% energy by washing a full load instead of 2 half
loads.
DO YOU NEED TO PRE-WASH?
For heavily soiled laundry only!
SAVE detergent, time, water and between 5 to 15% energy
consumption by NOT selecting Prewash for slight to normally
soiled laundry.
IS A HOT WASH REQUIRED?
Pretreat stains with stain remover or soak dried in stains in water
before washing to reduce the necessity of a hot wash
programme.
Save up to 50% energy by using a 60°C wash programme.
BEFORE USING A DRYING PROGRAMME...
SAVE energy and time by selecting a high spin speed to
reduce the water content in laundry before using a drying
programme.
26
29
CHAPTER 12
DRYING
DON’T DRY GARMENTS MADE FROM FOAM RUBBER
OR FLAMMABLE MATERIALS.
IMPORTANT:
THIS DRYER CAN ONLY BE USED FOR LAUNDRY
WHICH HAS BEEN WASHED AND SPIN DRIED.
WARNING:
Indications given are general, therefore some practice is
needed for the best drying results. We recommend setting a
lower drying time than indicated, when first using, so as to
establish the degree of dryness required. We recommend
not to dry fabrics that fray easily, such as rugs or garments
with a deep pile, to avoid air duct clogging.
The water is then conveyed to the drain circuit,which is
sealed and therefore, no steam can be released outside.
28
● Ensure that the water inlet tap is turned on.
● And that the discharge tube is in place.
PROGRAMME SELECTION
Refer to the programme guide to select the most suitable
programme.
Turning the selector knob required programme is activate.
Wait for the “STOP”indicator light to flash.
Then press the START button.
When the START button is pressed the machine sets the
working sequence in motion.
The programme carries out with the programme selector
stationary on the selected programme till cycle ends.
Warning: If there is any break in the power supply while the
machine is operating, a special memory stores the selected
programme and,when the power is restored, it continues
where it left off.
● At the end of the programme the indicator light “end
cycle” will go on.
● When the programme has finished
Wait for the door lock to be released (about 1 minute after
the programme has finished).
Switch off the machine by turning the programme selector
to the “OFF” position.
Open the door and remove the laundry.
Turn OFF the water supply after every use.
FOR ALL TYPES OF WASH CONSULT THE PROGRAMME
TABLE AND FOLLOW THE OPERATIONS IN THE ORDER
INDICATED.
31
4 kg MAX
The correct way to dry:
● Open door.
● Fill with up to 4 kg - in case of large items (e.g. sheets) or
very absorbent items (e.g. towels or jeans),it is a good idea
to reduce the load.
● Close door.
● Turn programme dial to cotton .
● Select the degree of dryness that you require.
This ranges from Extra Dry ( ) for bath towels and
bathrobes, through Cupboard Dry ( ) for items that will be
put away without ironing, to iron dry ( ) that leaves the
laundry suitable
for ironing.
If you wish to select a timed drying cycle, press the “drying
programme selection” button until the required time
indicator lights up.
DOUBLE-SKIN DOOR
The appliance door is fitted with a protective shield to
prevent contact being made with the glass which reaches
high temperatures, particularly during the drying cycle.
WARNING: DO NOT TOUCH DOOR FOR ANY REASON
WHATSOEVER.
● Make sure water tap is open.
● Make sure water drain is correctly positioned.
30
IMPORTANT
NEVER OPEN THE DOOR AFTER THE DRYING CYCLE
HAS BEGUN - WAIT UNTIL THE COOL DOWN PERIOD
PROVIDED FOR BY THE CYCLE.
Only dry pre-spun laundry
The washer/dryer can perform two types of drying:
Cotton, terry towelling,linen, hemp fabrics, etc...
Advisory note
During drying phase the drum will accelerate to a higher
speed to distribute the load and to optimize the drying
performance
Mixed fabrics (synthetics/cotton), synthetic fabrics.
33
PROGRAMME
Extra
Wardrobe
Iron
Min 1 Kg
from 30’
from 30’
from 30’
Min 1 Kg
from 30’
from 30’
from 30’
Max 3 Kg
to 170’
to 150’
to 80’
COTTON MIXED
TABLE OF DRYING TIMES (IN MINUTES):
Max 4 Kg
to 230’
to 220’
to 170’
32
WARNING:
DO NOT DRY WOOLLEN GARMENTS OR ARTICLES WITH
SPECIAL PADDING, (E.G. QUILTS, QUILTED ANORAKS,
ETC.).
DELICATE FABRICS IF GARMENTS ARE DRIP/DRY, LOAD
LESS ITEMS AO AS TO PREVENT CREASING.
● Press the START button.
● The drying phase will begin with the programme dial fixed
on the symbol until the end of drying.
● The drying programme indicator will be on until the cool
down phase will begin and the indicator ( ) will go on.
● At the end of the programme the indicator light “Stop” will
go on.
● Wait for the door lock to be released (about 1 minute after
the programme has finished).
The "Door Security" indicator light will go out.
● Switch off the machine by turning the programme selector
on the “OFF” position.
● Open the door and remove the laundry.
● Turn off the water supply after every use.
USEFUL TIPS:
Do not dry unwashed items in the washer dryer.
Items that have been soiled with substances such as cooking oil, acetone, alcohol,
petrol, kerosene, spot removers, turpentine, waxes and wax removers should be
washed in hot water with an extra amount of detergent before being dried in the
washer dryer.
Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted with foam rubber pads should not be
dried in the washer dryer.
Fabric softeners, or similar products, should be used as specified by the fabric softener
instructions.
The final part of a washer dryer cycle occurs without heat (cool down cycle) to
ensure that the items are left at a temperature that ensures that the items will not be
damaged.
WARNING:
Never stop a washer dryer before the end of the drying cycle unless all items are
quickly removed and spread out so that the heat is dissipated.
35
The programme carries out with the programme selector
stationary on the selected programme till cycle ends.
The washer-dryer will then complete the entire drying
programme.
The drying programme indicator will be on until the cool
down phase will begin and the indicator ( ) will go on.
At the end of the programme the indicator light “Stop” will
go on.
Wait for the door lock to be released (about 1 minute after
the programme has finished).
The "Door Security" indicator light will go out.
Switch off the machine by turning the programme selector
on the “OFF” position.
Open the door and remove the laundry.
Turn off the water supply after every use.
34
CHAPTER 13
AUTOMATIC WASHING/DRYING
WARNING: ONLY A MAXIMUM 4 KG OF DRY LAUNDRY
CAN BE LOADED OTHERWISE THE DRIED LAUNDRY WILL
BE NOT SATISFACTORY.
Washing:
Open the drawer, choose the detergent and put in the
correct amount.
Refer to the list of washing programmes according to fabrics
to be washed (e.g.very dirty cotton) and without pressing
Start button, prepare wash as described:
Turning the selector knob, the required programme is
activated.
Press the option buttons (if required)
Check that the tap is turned on and that the discharge hose
is positioned correctly.
Drying:
Select the degree of dryness that you require.
This ranges from Extra Dry ( ) for bath towels and
bathrobes, through Cupboard Dry ( ) for
items that will be put away without ironing, to iron dry ( )
that leaves the laundry suitable for ironing.
If you wish to select a timed drying cycle, press the “drying
programme selection” button until the required time indicator
lights up.
Press the "Start/Pause" button.
4 kg MAX
36
CHAPTER 14
CLEANING AND ROUTINE MAINTENANCE
Do not use abrasives, spirits and/or diluents on the exterior of
the appliance. It is sufficient to use a damp cloth.
The washing machine requires very little maintenance:
● Cleaning of drawer compartments.
● Removals or long periods when the machine is left
standing.
CLEANING OF DRAWER COMPARTMENTS
Although not strictly necessary, it is advisable to clean the
detergent, bleach and additives compartments occasionally.
Remove the compartments by pulling gently.
Clean with water.
Put the compartments back into place
36
REMOVALS OR LONG PERIODS WHEN THE MACHINE IS LEFT
STANDING
When the machine is left standing for long periods in
unheated rooms, the drain hose should be emptied of all
remaining water.
This operation is recommended when moving the appliance
from its installation.
The appliance must be switched off and unplugged. A bowl
is needed. Detach the drainage hose from the clamp and
lower it over the bowl until all the water is removed.
Repeat the same operation with the water inlet hose.
Advisory note
During drying phase the drum will accelerate to a higher speed to distribute the load and to
optimize the drying performance
38
CHAPTER 15
FAULT
If the fault should persist, contact a Technical Assistance Centre.For prompt servicing, give the model of the
washing machine, to be found on the label placed on the cabinet inside of the porthole.
Important
1 The use of environment friendly detergents without phosphates may produce the following effects:
- The discharge rinse water may result cloudier due to the presence of zeolites in suspension. This does not
compromise the efficiency of the rinses.
- The presence of white powder (zeolites) on the washing at the end of the washing cycle. This does not
remain incorporated in the fabric and does not alter the colour.
- The presence of foam in the last rinse water which is not necessarily a sign of inadequate rinsing.
- The non-ionic surface-active agents present in the composition of washing machine detergents are often
difficult to remove from the washing itself and, even in small quantities, may produce visible signs of the
formation of foam.
- Carrying out further rinses, in cases such as this, is not useful.
2 If your washing machine fails to function, carry out the above-mentioned checks before calling the Technical
Assistance Service.
1. Does not function
on any
programme
2. Does not load
water
3. Does not discharge
water
4.Water on floor
around washing
machine
5. Does not spin
6. Strong vibrations
during spin
Mains plug not plugged in
Mains switch not on
No power
Electric circuit fuses failure
Load door open
See cause 1
Inlet tap turned off
Discharge tube bent
Leak from the washer between the tap
and inlet tube
The washing machine has not
discharged water
“No spin” setting (some models only)
Washing machine not perfectly level
Transport bracket not removed
Washing load not evenly distributed
Insert plug
Turn on mains switch
Check
Check
Close load door
Check
Turn on water inlet tap
Straighten discharge tube
Replace washer and tighten the tube
on the tap
Wait a few minutes until the machine
discharges water
Turn the programme dial onto spin
setting
Adjust special feet
Remove transport bracket
Distribute the washing evenly
CAUSE
REMEDY
39
Our Customer Care Centre can be called on:
0871 22 22 503
We aim to answer calls as quickly as possible, and in strict rotation as soon as one of our
Customer Care team become free.
Our Customer Care Centre opening hours are:
Monday - Friday 8.00am - 8.00pm
Saturday 8.30am - 6.00pm
Sunday 10.00am - 4.00pm
Please ensure that you have available your appliances model number and serial number,
there is a space at the back of this book for recording that information.
Alternatively visit the web site as detailed on the front cover of the handbook.
Outside the UK and Northern Ireland, please contact your local supplier.
CONTACT US
In case of difficulty within the UK and Northern Ireland, please call Belling Customer Care
Centre Helpline on
0871 22 22 503
Our Customer Care Centre is open during the hours below:
Monday to Friday 8am - 8pm
Saturday 8.30am - 6pm
Sunday 10am - 4pm
Please have to hand your appliances Model Number and Serial Number, which can be found
on the databadge inside you cooker and recorded here for future reference.
Glen Dimplex Home Appliances Limited is the owner of the Belling brand and is part of
the Glen Dimplex group of companies.
Stoney Lane, Prescot,Merseyside, L35 2XW
08 26369 00 © 2006
Model Number
Serial Number
NOTE:
THE MACHINE IS FITTED WITH A SPECIAL ELECTRONIC DEVICE, WHICH PREVENTS THE SPIN CYCLE
SHOULD THE LOAD BE UNBALANCED.
THIS REDUCES THE NOISE AND VIBRATION IN THE MACHINE AND SO PROLONGS THE LIFE OF YOUR
MACHINE.
Page is loading ...
/