Boston Acoustics Horizon HPS 10HO User manual

OWNER’S MANUAL / SAFETY INSTRUCTIONS / COMPLIANCE INFORMATION

HPS 10HO

HPS 10SE

HPS 12HO

Boston Horizon Subwoofers

A Boston P.O.P. Product Make it your own...

Español

Subwoofers Boston Horizon

Manual del Propietario /

Instrucciones de Seguridad /

Información de Cumplimiento

Français

Caissons de graves Boston

Horizon

Guide de l’utilisateur /

Instructions de sécurité /

Informations relatives à la

conformité

Italiano

Subwoofer Boston Horizon

Manuale dell’utente/Istruzioni

di sicurezza/Informazioni sulla

conformità

Svenska

Boston Horizon Subwoofers

Bruksanvisning /

säkerhetsanvisningar

/ information om

överensstämmelse

Deutsch

Boston Horizon

Basslautsprecher

Bedienungsanleitung

/ Sicherheitshinweise /

Konformitätserklärung

IMPORTANT SAFETY INSTRUCTIONS

This symbol found on the apparatus indicates hazards

arising from dangerous voltages.

This symbol found on the apparatus indicates the user

should read all safety statements found in the user

manual.

This symbol found on the apparatus indicates double

insulation.

WARNING! To reduce the risk of  re or electri-

cal shock, do not expose this apparatus to rain or

moisture.

This symbol found on the apparatus indicates that

the apparatus must be placed in a separate collection

facility for electronic waste and not dosposed with

household waste.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampli ers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding type plug. A polarized plug has two blades with

one wider than the other. A grounding-type plug has two

blades and a third grounding prong. The wide blade or

the third prong is provided for your safety. If the provided

plug does not  t into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories speci ed by the manu-

facturer.

12. Unplug this apparatus during lightning storms or when

unused for long periods of time.

13. Refer all servicing to quali ed service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

14. Maintain a minimum distance of 2” (50mm) around the

front, rear, and sides of the apparatus for su cient ventila-

tion. The ventilation should not be impeded by covering the

ventilation openings or placing on or around the apparatus

items such as newspapers, table-cloths, curtains, etc.

15. No open  ame sources, such as lighted candles, should be

placed on the apparatus.

16. The apparatus shall not be exposed to dripping or splash-

ing. No objects  lled with liquids, such as vases, shall be

placed on the apparatus.

17. Either the power inlet connector on the rear of the appara-

tus or the power plug at the wall must remain accessible, to

be able to disconnect power from the apparatus.

18. To completely disconnect this apparatus from the AC Mains,

disconnect the power supply cord plug from the AC recep-

tacle.

19. The mains plug of the power supply cord shall remain read-

ily operable.

American Users:

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable pro-

tection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio commu-

nications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can

be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit di er-

ent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Canadian Users

This class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de classe B est conforme á la norme

NMB-003 du Canada.

3

Speci cations HPS 10HO HPS 10SE HPS 12HO

Frequency Range: 35Hz – 150Hz 35Hz – 150Hz 25Hz – 150Hz

Ampli er Power: 250 watts RMS 150 watts RMS 300 watts RMS

Bass Driver: 10” (254mm) DCD 10” (254mm) DCD 12” (305mm) DCD

Dimensions: (H x W x D) 16

5

⁄8 x 16

5

⁄8 x 12

7

⁄8” 17

5

⁄8 x 17

5

⁄8 x 13

5

⁄8” 17

5

⁄8 x 17

5

⁄8 x 13

5

⁄8”

(420 x 420 x 326mm) (445 x 445 x 345mm) (445 x 445 x 345mm)

Weight: 34

5

⁄8 lbs 38

1

⁄4 lbs 45

13

⁄16 lbs

(15.7kg) (17.4kg) (20.8kg)

.

Introduction

Boston Acoustics Horizon Subwoofers

Thank you for choosing Boston Acoustics. The Horizon subwoofers incorporate high-quality components that produce the

famous Boston Sound. The subwoofers are ideally suited for use in a high-quality 5.1 channel home theater or stereo music

system. They are capable of impressive deep bass and high output from remarkably compact enclosures. In addition, they

feature BassTrac®, a proprietary Boston-designed circuit that tracks the input signal to the subwoofer and prevents its ampli-

 er from being driven into audible distortion. The bene t: the bass stays clean and strong at any listening level.

Horizon Subwoofers are designed to literally sound as good as they look. With their elegant pro les and the soft smooth

surfaces of their back cabinets, Horizon Subwoofers complement the décor of any room and o er no-compromise audio

excellence.

Features

• 10 and 12” woofers

• 150 to 300 watts RMS

• High-output front- ring, rear-ported design

• Deep Channel® Design (DCD) woofers for more bass from less ampli er power

• BassTrac circuitry for tight, distortion-free bass at all output levels

• Adjustable polarity and gain control

• Adjustable foot

• Ultra-rigid reinforced cabinetry

• Soft-touch  nish with color coordinated rubber trim (except HPS 10SE)

4

Unpacking the System

Carefully unpack the subwoofer. If there is any sign of damage from transit, report it immediately to your dealer and/or de-

livery service. Keep the shipping carton and packing materials for future use. Be sure to keep your purchase receipt in a safe

place, as it may be required for warranty purposes.

Placement Options

Place the subwoofer next to a wall or in a corner near your main speakers. The sound is typically best when the subwoofer is

within 15 feet (4.5m) of the main speakers. The sharp 24dB/octave crossover roll-o permits placement farther from the main

speakers if necessary. Since the ear is unable to localize the low frequencies of the subwoofer, the bass still appears to come

from the main speakers. Experimentation is key, however most positions in the room will work well.

The level of bass output from the subwoofer will vary at di erent positions in a room. When placed near walls, its loudness is

emphasized. Corner placement provides the most bass output. Placement completely away from walls may produce too little

bass. Regardless of the natural bass level within the room you will always have the ability to adjust the level of the subwoofer

from the built in volume control. If at any time you move the subwoofer be sure to check all of your settings.

The foot on the rear of the subwoofer can be removed to produce a slight backward tilt. Remove the thumbscrew from the

back of the foot to remove it. It is slotted for easy removal with a screwdriver or a coin.

IMPORTANT: Do not place the subwoofer where there is a chance of contact between the rear panel and drapes or furniture

.

HPS 10HO, HPS 10SE and HPS 12HO subwoofers with removable feet.

M

E

N

U

/

E

N

T

E

R

I

N

P

U

T

S

E

L

E

C

T

D

O

W

N

U

P

L

E

F

T

/

-

R

I

G

H

T

/

+

/

E

X

I

T

V

O

L

U

M

E

P

O

W

E

R

/

S

T

A

N

D

B

Y

Position subwoofer

in corner for maximum

bass output

5

Connections

After your speakers are properly placed, you are ready to wire your system.

NOTE: Power is always supplied to the subwoofer electronics unless it is unplugged or switched to the o position using the

power switch located on the rear panel. The auto-on circuitry only activates or deactivates the power ampli er. Make sure

your subwoofer and receiver are unplugged when making the connection.

Power: When plugging your subwoofer in be sure to use a wall outlet, or dedicated electrical outlet. Some receivers will

provide a switched outlet. Do not use this. These on board electrical outlets do not o er the amount of current or proper

isolation required by a power ampli er, such as the one in your ampli er.

Line level or LFE: On most systems use the line level input or the LFE input. These inputs accept the line-level signal from

your receiver’s subwoofer output. Your receiver’s manual should indicate which input is most appropriate.

Connecting the Subwoofer to Digital Home Theater Systems Using LFE

Digital 5.1, 6.1 and 7.1 home theater electronics dedicate one channel (the “.1”) to reproduce the special low-frequency (LFE)

information (such as explosions and thunder) contained in digitally-encoded soundtracks.

Select ”subwoofer-yes” from your receiver’s set-up menu. Hooked up this way, the receiver’s ampli er is relieved of having to

reproduce the di cult low bass signals that can drive the receiver into audible distortion. In some cases it can also depend on

several other settings within a receiver. We recommend consulting your receiver manual for further assistance in this area.

Use an RCA cable (not included), as shown, to connect your digital receiver’s LFE subwoofer output to the subwoofer.

Connect the other end to the LFE input.

digital receiver

Connecting the Subwoofer to Stereo or Dolby® Pro Logic®

For stereo or Dolby Pro Logic systems use the “sub out” connection from your receiver to the input on the subwoofer marked

“Left” and “Right”.

receiver

use either input

6

Connecting to Electronics Without a Subwoofer Output

If the electronic in your system does not have a subwoofer of LFE output you can connect the HPS units to a preamp output.

Use a stereo RCA cable (not included) to connect the preamp outputs to the Left and Right Line Level inputs.

Adjusting the Crossover Control

When using the Line Level inputs (not the LFE input) the subwoofer’s built-in crossover is engaged. As a starting point, set the

crossover control on the subwoofer about 10Hz higher than the lower limit of your main speakers’ bass response. Fine -tune

the crossover setting by ear for the smoothest blend with your main speakers. The best setting of the crossover control will

depend on speaker placement and personal preference

Operation

Power On/Auto/Standby

Plug the subwoofer’s AC cord into a wall outlet. Do not use the outlets on the back of the receiver. Set the power switch to

the desired setting.

OFF – The subwoofer is o and will not produce any sound. You may want to turn your subwoofer o if you will not be using

it for some time or wish to conserve electricity.

AUTO – The subwoofer will power on whenever a signal is detected. If no signal is detected after several minutes, it will auto-

matically enter the Standby mode.

ON – The subwoofer is always on.

An LED indicator between the Power switch and the Polarity switch indicates what mode the subwoofer is in.

OFF – The subwoofer is o

RED – STANDBY (No signal detected, Amp O )

GREEN – ON (Signal detected, Amp On)

The subwoofer will automatically enter the Standby mode after several minutes when no signal is detected from your system.

The subwoofer will then power ON instantly when a signal is detected.

Crossover Control

Adjusts the frequency of the low pass  lter for the subwoofer. Note: This control is not active when using the LFE input jack.

Volume Control

Turn the subwoofer Volume control to the 11 o’clock position. If no sound emanates from the subwoofer, check the AC-line

cord, Power switch, and input cables. (Are the connectors on the cables making proper contact? Is the AC-line cord connect-

ed to a “live” receptacle, is the subwoofer in either the Auto or On position?)

Adjust the subwoofer Volume control until you hear a match between the main speaker and subwoofer. Bass response should

not overpower the room but rather be adjusted so there is a natural blend across the entire musical range.

7

Polarity Control

(0° or 180°): Selects regular (0°) or inverted (180°) phase for the subwoofer. Set this switch to provide the fullest, most

dynamic bass. The e ect of phase will be most audible on low-frequency percussion instruments or music with a continuously

repeating bass line.

Maintenance and Service

All wiring connections should be inspected and cleaned or remade at least once a year.

If a problem does occur, make sure that all connections are properly made, secure and clean. If a problem occurs in one

loudspeaker, rewire that speaker in a di erent location within the system. Should the problem persist then the problem is

within the speaker. If the speaker sounds  ne in the new position it is a strong indication of a more in depth issue with the

electronics in the system. In the event that your speakers ever need service, contact your local Boston Acoustics dealer or

visit www.bostonacoustics.com/dealers for a list of dealers in your area.

Limited Warranty

Boston Acoustics warrants to the original purchaser of an HPS subwoofer that it will be free of defects in materials and

workmanship in its mechanical parts for a period of 5 years from the date of purchase. The warranty period for the electrical

components is 1 year.

Your responsibilities are to install and use them according to the instructions supplied, to provide safe and secure transporta-

tion to an authorized Boston Acoustics service representative, and to present proof of purchase in the form of your sales slip

when requesting service.

Excluded from this warranty is damage that results from abuse, misuse, improper installation, accidents, shipping, or repairs/

modi cations by anyone other than an authorized Boston Acoustics service representative.

This warranty is limited to the Boston Acoustics product and does not cover damage to any associated equipment. This

warranty does not cover the cost of removal or reinstallation. This warranty is void if the serial number has been removed or

defaced. This warranty gives you speci c legal rights, and you may also have other rights which vary from state to state.

If Service Seems Necessary

First, contact the dealer from whom you purchased the product. If that is not possible, write to:

Boston Acoustics, Inc.

300 Jubilee Drive

Peabody, MA 01960 USA

Or contact us via e-mail at:

[email protected]

We will promptly advise you of what action to take. If it is necessary to return your HPS subwoofer to the factory, please ship it

prepaid. After it has been repaired, we will return it freight prepaid in the United States and Canada.

For EU Customers Only

This symbol found on the product indicates that the product must not be disposed of with household waste.

Instead, it may be placed in a separate collection facility for electronic waste or returned to a retailer when pur-

chasing similar product. The producer paid to recycle this product. Doing this contributes to reuse and recycling,

minimizes adverse e ects on the environment and human health and avoids any  nes for incorrect disposal.

Page is loading ...

40

300 Jubilee Drive, Peabody, MA 01960 USA

www.bostonacoustics.com

ellipse symbol are trademarks of Boston Acoustics, Inc.

Dolby Digital, and Dolby Pro Logic are registered trademarks of Dolby

Laboratories.

Speci cations are subject to change without notice. 142-003051-0

Boston Acoustics Horizon HPS 10HO User manual

Boston Acoustics Horizon HPS 10HO User manual

in other languages

Related papers

Other documents