2. Home
  3. Domestic appliances
  4. Sanitary ware
  5. rainlex
  6. RX93101BN-10
RX93101BN-10

rainlex RX93101BN-10 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the rainlex RX93101BN-10 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INDEX
1. CUPC Certification. . . . . . . . . . . . . . . . . . . . . P01-02
2. Installation Preparation & Maintenance. . . . . . P03
3. 93101-10/12. . . . . . . . . . . . . . . . . . . . . . . . . . . P04-06
4. 96201-10/12. . . . . . . . . . . . . . . . . . . . . . . . . . . .P07-09
5. 96202-10/12 . . . . . . . . . . . . . . . . . . . . . . . . . . . P10-12
6. 96205-10/12. . . . . . . . . . . . . . . . . . . . . . . . . . . .P13-15
7. 96207. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P16-18
8. 96203-10/12. . . . . . . . . . . . . . . . . . . . . . . . . . . .P19-21
383mm
15.07inch
1/2-14NPT 358mm
14.09inch
2200-2500mm
86.61-98.42inch
1000-1500mm
39.37-59.05inch
152mm
5.98inch
152mm
5.98inch
Min.60mm
(2.36inch)
Max.80mm
(3.15inch)
Finish wall
3-1/2-14 NPT
HC
1
3
4567
89
10
2
HC
No Description QTY
1Rough-in Valve 1
2Protective Cover 1
3Panel 1
4On/off Handle 1
5Hexagonal Screw 1
6Allen Key 1
7 Decorative Hat 1
8Decorative Cover 1
9Shower Arm 1
10 Shower Head 1
Installation Instruction
Model: 93101-10/12
Installation Instruction 1/3
250mm
10inch
Adjustable Degree
MAX:1300mm 51inch
Coverage of The Spray Water
6mm
0.23inch
Stringer or base surface
4
95mm
3.74inch
70mm
2.75inch
145mm
5.7inch
Hot Water Cold Water
Mixer Water
Tile surface
Wall
Max.80mm
3.15inch Min.60mm
2.36inch
Pipe Connection
1.Please drill the holes on the wall for the main body embedded part,
hot and cold water inlet pipes as well as shower arm connection
pipes according to the basic product dimension drawing as below.
2.Please make hot and cold water inlet pipe, the mixed water outlet
pipe connect with control valve, and tighted with the wrench.
Water Testing And Sealing Testing
1.After the pipeline connection is completed, unscrew the stop valve, open
the pipeline switch to flush the impurities and sludge to avoid blockage and
affect the water flow function;
2.Close the switch, re-tighten the stop valve and open the switch again to
make the pipeline is under pressure. Check the pressure resistance and
sealing performance of the valve and pipeline to ensure that there is no
leakage in the pipeline.
Head Shower
Hot Water Cold Water
Model: 93101-10/12
Installation Instruction 2/3
2.The depth of the embedded box is 2.36” - 3.15”
It's better to drill the depth of 2.36''for blank wall
1.The size of the embedded box that needs
to be drilled is 5.7” *3.74”
5
Tile or wooden surface
Wall
Outside the wall
≥25mm
0.98inch
The Procedure of Sealing The Wall
Use a parallel ruler to measure the flatness of the embedded box casing and the vertical wall surface. If the wall surface is not flat, it should be patched
to ensure the embedded box casing and vertical wall angle meets at nearly ideal angle of 90, then lay the tile decoration.
Head Shower Installation
2. The panel and the handle are connected to
the control valve as shown below sequence
1.Take off the protective cover
Installation of Rough-in Valve
1.Wrap the tape around the pipe thread
and screw it on the wall hole
2.Screw the head shower onto the outlet
pipe thread
H
C
Model: 93101-10/12
Installation Instruction 3/3
6
1
2
3
4
567
8
9
10
No Description QTY
1Rough-in Valve 1
2Protective Cover 1
3Panel 1
4On/off Handle 1
5Hexagonal Screw 1
6Allen Key 1
7 Decorative Hat 1
8Decorative Cover 1
9Shower Arm 1
10 Shower Head 1
Min.60mm
(2.36inch)
Max.80mm
(3.15inch)
Finish wall
3-1/2-14 NPT
375mm
14.76inch
364mm
14.33inch
1/2-14NPT
1000-1500mm
39.37-59.05inch
∅160 mm
6.3inch
Installation Instruction
H
C
H C
Model: 96201-10/12
Installation Instruction 1/3
2200-2500mm
86.61-98.42inch
6mm
0.23inch
∅250mm
∅10inch
Adjustable Degree
MAX:1300mm 51inch
Coverage of The Spray Water
Stringer or base surface
7
Pipe Connection
1.Please drill the holes on the wall for the main body embedded part,
hot and cold water inlet pipes as well as shower arm connection
pipes according to the basic product dimension drawing as below.
2.Please make hot and cold water inlet pipe, the mixed water outlet
pipe connect with control valve, and tighted with the wrench.
Water Testing And Sealing Testing
1.After the pipeline connection is completed, unscrew the stop valve, open
the pipeline switch to flush the impurities and sludge to avoid blockage and
affect the water flow function;
2.Close the switch, re-tighten the stop valve and open the switch again to
make the pipeline is under pressure. Check the pressure resistance and
sealing performance of the valve and pipeline to ensure that there is no
leakage in the pipeline.
Head Shower
Hot Water Cold Water
Model: 96201-10/12
Installation Instruction 2/3
95mm
3.74inch
70mm
2.75inch
145mm
5.7inch
Hot Water Cold Water
Mixer Water
Tile surface
Wall
Max.80mm
3.15inch Min.60mm
2.36inch
2.The depth of the embedded box is 2.36” - 3.15”
It's better to drill the depth of 2.36''for blank wall
1.The size of the embedded box that needs
to be drilled is 5.7” *3.74”
8
Tile or wooden surface
Wall
Outside the wall
≥25mm
0.98inch
The Procedure of Sealing The Wall
Use a parallel ruler to measure the flatness of the embedded box casing and the vertical wall surface. If the wall surface is not flat, it should be patched
to ensure the embedded box casing and vertical wall angle meets at nearly ideal angle of 90, then lay the tile decoration.
Head Shower Installation
2. The panel and the handle are connected to
the control valve as shown below sequence
H
C
1.Take off the protective cover
Installation Of Rough-in Valve
1.Wrap the tape around the pipe thread
and screw it on the wall hole
2.Screw the head shower onto the outlet
pipe thread
Model: 96201-10/12
Installation Instruction 3/3
9
1
1
3
2
4
5
89
10
11
12
13
14
15 16
17
18
No Description QTY
1Rough-in Valve 1
2 Protective Cover 1
3Protective Cover 1
4 Panel 1
5Diverter Knob 1
6Hexagonal Screw 1
7Decorative Hat 1
8On/off Handle 1
9Hexagonal Screw 1
10 Allen Key 1
11 Decorative Hat 1
12 Decorative Cover 1
13 Shower Arm 1
14 Shower Head 1
15 Decorative Cover 1
16 Handle Shower 1
17 Shower Holder 1
18 Shower Hose 1
67
Finish wall
4-1/2-14 NPT
1/2-14 NPT
1000-1500mm
39.37-59.05inch
∅180
mm
7.08inch
243mm
9.56inch
1.5m
59inch
67mm
2.63inch
1200-1600mm
47.2-63inch
Technical Drawing of Dual Function
Min.60mm
2.36inch
Max.80mm
3.15inch
HC
HC
375mm
14.76inch
364mm
14.33inch
1/2-14NPT
2200-2500mm
86.61-98.42inch
6mm
0.23inch
∅250mm
∅10inch
Adjustable Degree
Model: 96202-10/12
Installation Instruction 1/3
MAX:1300mm 51inch
Coverage of The Spray Water
Stringer or base surface
10
170mm
6.7inch
130mm
5.12inch
145mm
5.7inch
Hot Water Cold Water
Mixer Water
Mixer Water
Tile surface
Wall
Max.80mm
3.15inch Min.60mm
2.36inch
Cold Water
Hot Water
Head Shower
Handheld Shower
Pipe Connection
1.Please drill the holes on the wall for the main body embedded part,
hot and cold water inlet pipes as well as shower arm connection
pipes according to the basic product dimension drawing as below.
2.Please make hot and cold water inlet pipe, the mixed water outlet
pipe connect with control valve, and tighted with the wrench.
Water Testing And Sealing Testing
1.After the pipeline connection is completed, unscrew the stop valve, open
the pipeline switch to flush the impurities and sludge to avoid blockage and
affect the water flow function;
2.Close the switch, re-tighten the stop valve and open the switch again to
make the pipeline is under pressure. Check the pressure resistance and
sealing performance of the valve and pipeline to ensure that there is no
leakage in the pipeline.
Model: 96202-10/12
Installation Instruction 2/3
2.The depth of the embedded box is 2.36” - 3.15”
It's better to drill the depth of 2.36''for blank wall
1.The size of the embedded box that needs
to be drilled is 5.7” *6.7”
11
Wall
Outside the wall
≥25mm
0.98inch
The Procedure of Sealing The Wall
Use a parallel ruler to measure the flatness of the embedded box casing
and the vertical wall surface.If the wall surface is not flat, it should be
patched to ensure the embedded box casing and vertical wall angle meets
at nearly ideal angle of 90, then lay the tile decoration.
Handle Shower Installation
Tile or wooden surface
Head Shower Installation
1.Wrap the tape around the pipe thread and screw it on the wall hole
2.Screw the head shower onto the outlet pipe thread
Shower Holder Installation
1. Take off the two screws in the bottom of the shower seat.
2. Wrap the tape around the pipe thread and screw the seat on the wall hole
3. Screw the two screws on again
1.Take off the protective cover 2. The panel and the handle are
connected to the control valve
as shown below sequence
Installation of Rough-in Valve
Model: 96202-10/12
Installation Instruction 3/3
12
No Description QTY
1Rough-in Valve 1
2 Protective Cover 1
3Protective Cover 1
4 Panel 1
5Diverter Knob 1
6Hexagonal Screw 1
7Decorative Hat 1
8On/off Handle 1
9Hexagonal Screw 1
10 Allen Key 1
11 Decorative Hat 1
12 Decorative Cover 1
13 Shower Arm 1
14 Shower Head 1
15 Decorative Cover 1
16 Handle Shower 1
17 Shower Holder 1
18 Shower Hose 1
Model: 96205-10/12
Installation Instruction 1/3
1
1
3
2
4
5
89
1011
13
14
15 16
17
18
67
HC
12
Finish wall
4-1/2-14 NPT
1/2-14 NPT
1000-1500mm
39.37-59.05inch
∅180
mm
7.08inch
243mm
9.56inch
67mm
2.63inch
1200-1600mm
47.2-63inch
Technical Drawing of Dual Function
Min.60mm
2.36inch
Max.80mm
3.15inch
HC
Min.360mm
14.17inch
200mm
7.87inch
1/2-14NPT
Adjustable Degree
MAX:1300mm 51inch
Coverage of The Spray Water
6mm
0.23inch
∅250mm
∅10inch
1.5m
59inch Stringer or base surface
13
Cold Water
Hot Water
Head Shower
Bathtub spout
Pipe Connection
1.Please drill the holes on the wall for the main body embedded part,
hot and cold water inlet pipes as well as shower arm connection
pipes according to the basic product dimension drawing as below.
2.Please make hot and cold water inlet pipe, the mixed water outlet
pipe connect with control valve, and tighted with the wrench.
Water Testing And Sealing Testing
1.After the pipeline connection is completed, unscrew the stop valve, open
the pipeline switch to flush the impurities and sludge to avoid blockage and
affect the water flow function;
2.Close the switch, re-tighten the stop valve and open the switch again to
make the pipeline is under pressure. Check the pressure resistance and
sealing performance of the valve and pipeline to ensure that there is no
leakage in the pipeline.
Model: 96205-10/12
Installation Instruction 2/3
170mm
6.7inch
130mm
5.12inch
145mm
5.7inch
Hot Water Cold Water
Mixer Water
Mixer Water
Tile surface
Wall
Max.80mm
3.15inch Min.60mm
2.36inch
2.The depth of the embedded box is 2.36” - 3.15”
It's better to drill the depth of 2.36''for blank wall
1.The size of the embedded box that needs
to be drilled is 5.7” *6.7”
14
Wall
Outside the wall
≥25mm
0.98inch
The Procedure of Sealing The Wall
Use a parallel ruler to measure the flatness of the embedded box casing
and the vertical wall surface.If the wall surface is not flat, it should be
patched to ensure the embedded box casing and vertical wall angle meets
at nearly ideal angle of 90, then lay the tile decoration.
Handle Shower Installation
Tile or wooden surface
Head Shower Installation
1.Wrap the tape around the pipe thread and screw it on the wall hole
2.Screw the head shower onto the outlet pipe thread
Shower Holder Installation
1. Take off the two screws in the bottom of the shower seat.
2. Wrap the tape around the pipe thread and screw the seat on the wall hole
3. Screw the two screws on again
1.Take off the protective cover 2.The panel and the handle are
connected to the control valve
as shown below sequence
Installation of Rough-in Valve
Model: 96205-10/12
Installation Instruction 3/3
15
1
1
3
2
4
5
89
1011
12 13
14
15
No Description QTY
1Rough-in Valve 1
2Protective Cover 1
3 Protective Cover 1
4Panel 1
5Diverter Knob 1
6Hexagonal Screw 1
7 Decorative Hat 1
8On/off Handle 1
9Hexagonal Screw 1
10 Allen Key 1
11 Decorative Hat 1
12 Decorative Cover 1
13 Handheld Shower 1
14 Shower Holder 1
15 Shower Hose 1
16 Decorative Cover 1
17 Rotatable Bathtub Spout 1
67
Model: 96207
Dual Function Concealed Faucet Parts List 1/3
Technical Drawing of Dual Function
HC16
17
Min.60mm
(2.36inch)
Max.80mm
(3.15inch)
Finish wall
1000-1500mm
39.37-59.05inch
∅8.6
mm
7.08inch
4-1/2-14 NPT
1/2-14 NPT
243mm
9.56inch
243.5mm
9.58inc h
∅2.9 mm
2.36inch
1000-1500mm
39.37-59.05inch
1/2-14 NPT
1.5m
59inch
Stringer or base surface
16
Cold Water
Hot Water
Pipe Connection
1.Please drill the holes on the wall for the main body embedded part, hot
and cold water inlet pipes according to the basic product dimension drawing
as below.
2.Please make hot and cold water inlet pipe, the mixed water outlet pipe
connect with control valve, and tighted with the wrench.
Water Testing And Sealing Testing
1.After the pipeline connection is completed, unscrew the stop valve, open the
pipeline switch to flush the impurities and sludge to avoid blockage and affect
the water flow function;
2.Close the switch, re-tighten the stop valve and open the switch again to make
the pipeline is under pressure. Check the pressure resistance and sealing
performance of the valve and pipeline to ensure that there is no leakage in the
pipeline.
Model: 96207-10
Installation Instruction 2/3
Handheld Shower
Bathtub Spout
170mm
6.7inch
130mm
5.12inch
145mm
5.7inch
Hot Water Cold Water
Mixer Water
Mixer Water
Tile surface
Wall
Max.80mm
3.15inch Min.60mm
2.36inch
2.The depth of the embedded box is 2.36” - 3.15”
It's better to drill the depth of 2.36''for blank wall
1.The size of the embedded box that needs
to be drilled is 5.7” *6.7”
17
Wall
Outside the wall
≥25mm
0.98inch
The Procedure of Sealing The Wall
Use a parallel ruler to measure the flatness of the embedded box casing and
the vertical wall surface.If the wall surface is not flat, it should be patched
to ensure the embedded box casing and vertical wall angle meets at nearly
ideal angle of 90, then lay the tile decoration.
Handle Shower Installation
Tile or wooden surface
Tub Spout Installation
1. Take off the two screws in the bottom of the tub spout.
2.Wrap the tape around pipe thread, screw the tub spout on wall hole.
3.Screw the two screws on again.
Shower Seat Installation
1. Take off the two screws in the bottom of the shower seat.
2. Wrap the tape around the pipe thread and screw the seat on the wall hole
3. Screw the two screws on again
1.Take off the protective cover 2. The panel and the handle are
connected to the control valve
as shown below sequence
Installation of Rough-in Valve
Model: 96207-10
Installation Instruction 3/3
18
Page is loading ...
Page is loading ...
Page is loading ...
/