INSTALLATION INSTRUCTIONS FOR 110V POWER CORD KIT
FOR USE WITH MODELS MPE-33R AND MPE-36R ELECTRIC FIREPLACE
LENNOX HEARTH PRODUCTS 2004
P/N 775,178M REV.A 12/2005 Page 1 of 1 1110 West Taft Avenue • Orange, CA 92865
LENNOX HEARTH PRODUCTS
KITS AND ACCESSORIES
Cat. No. Model Description
H1645 PCK Power Cord Kit
775,178M REV.
A
12/2005
LENNOX reserves the right to make changes at any time, without notice, in design, materials,
specifications, prices, discontinued colors, styles and products. Consult your local distribu-
tor for fireplace code information.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
‘
KIT CONTENTS:
1 ea. Power Cord
1 ea. Cover Plate w/Cord Restraint
1 ea. Instruction Sheet
TOOLS REQURED:
Wire Stripper
Blunt Nose ("Linesman") Pliers
INSTALLATION INSTRUCTIONS:
Read all instructions completely before beginning installation.
Step 1. Strip the three wire ends on power cord, approximately
1/2” from the end.
Step 2. Connect wires as shown in Figure 2. Twist wires together
using a pair of blunt nose ("linesman") pliers, tightly, then twist
each wire nut on by hand. After twisting the connector on, give
each wire a tug, to ensure it is secure. DO NOT wrap the "open"
end of the connector with electrical tape to cover. If bare wire
is exposed outside the connector. Instead of taping it, the con-
nection should be redone.
Step 3. Ensure that all control switches are in the off position.
Step 4. Read WARNINGS then plug power cord into wall outlet.
WARNINGS:
• The power cord must not be pinched or against a sharp
edge. Secure cord to avoid tripping or snagging to reduce
the risk of fire, electric shock or personal injury.
• Do not run cord under carpeting. Do not cover cord with
throw rugs, runners or the like. Arrange cord away from
traffic areas and where it will not be tripped over.
• Power cord must plug into a dedicate circuit that is properly
grounded (3-prong), fused (15 Amp.) and polarized 110/120
Volt, 60 Hz outlet only. Note: A dedicated circuit is required
to prevent overloading a house circuit in cases of having
multiple appliances on the same circuit. Use an outlet
that is protected by a ground fault circuit interrupter where
required by electrical code.
• Avoid the use of an extension cord which may overheat
and cause a risk of fire. However, if an extension cord is
used, the cord shall be number 14 AWG minimum size
and rated not less than 1800 Watts, 15 Amps. The exten-
sion cord must be a three-wire cord with grounding type
plug and cord connection.
Cover
Plate
Figure 1
~
83”
Use Wire Nuts
Provided with
Appliance
POWER CORD KIT
Power
Cord
Co
r
d Restraint
N
L1
G
L1 = Black (Power)
N = White (Common)
G = Green (Ground)
Left Side of
Fireplace
Figure 2
Power Cord
Cover Plate
INSTALLATION INSTRUCTIONS FOR 110V POWER CORD KIT
FOR USE WITH MODELS MPE-33R AND MPE-36R ELECTRIC FIREPLACE
LENNOX HEARTH PRODUCTS 2004
P/N 775,178M REV.A 12/2005 Page 1 of 1 1110 West Taft Avenue • Orange, CA 92865
LENNOX HEARTH PRODUCTS
KITS AND ACCESSORIES
Cat. No. Model Description
H1645 PCK Power Cord Kit
775,178M REV.
A
12/2005
LENNOX reserves the right to make changes at any time, without notice, in design, materials,
specifications, prices, discontinued colors, styles and products. Consult your local distribu-
tor for fireplace code information.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
‘
KIT CONTENTS:
1 ea. Power Cord
1 ea. Cover Plate w/Cord Restraint
1 ea. Instruction Sheet
TOOLS REQURED:
Wire Stripper
Blunt Nose ("Linesman") Pliers
INSTALLATION INSTRUCTIONS:
Read all instructions completely before beginning installation.
Step 1. Strip the three wire ends on power cord, approximately
1/2” from the end.
Step 2. Connect wires as shown in Figure 2. Twist wires together
using a pair of blunt nose ("linesman") pliers, tightly, then twist
each wire nut on by hand. After twisting the connector on, give
each wire a tug, to ensure it is secure. DO NOT wrap the "open"
end of the connector with electrical tape to cover. If bare wire
is exposed outside the connector. Instead of taping it, the con-
nection should be redone.
Step 3. Ensure that all control switches are in the off position.
Step 4. Read WARNINGS then plug power cord into wall outlet.
WARNINGS:
• The power cord must not be pinched or against a sharp
edge. Secure cord to avoid tripping or snagging to reduce
the risk of fire, electric shock or personal injury.
• Do not run cord under carpeting. Do not cover cord with
throw rugs, runners or the like. Arrange cord away from
traffic areas and where it will not be tripped over.
• Power cord must plug into a dedicate circuit that is properly
grounded (3-prong), fused (15 Amp.) and polarized 110/120
Volt, 60 Hz outlet only. Note: A dedicated circuit is required
to prevent overloading a house circuit in cases of having
multiple appliances on the same circuit. Use an outlet
that is protected by a ground fault circuit interrupter where
required by electrical code.
• Avoid the use of an extension cord which may overheat
and cause a risk of fire. However, if an extension cord is
used, the cord shall be number 14 AWG minimum size
and rated not less than 1800 Watts, 15 Amps. The exten-
sion cord must be a three-wire cord with grounding type
plug and cord connection.
Cover
Plate
Figure 1
~
83”
Use Wire Nuts
Provided with
Appliance
POWER CORD KIT
Power
Cord
Co
r
d Restraint
N
L1
G
L1 = Black (Power)
N = White (Common)
G = Green (Ground)
Left Side of
Fireplace
Figure 2
Power Cord
Cover Plate
Figure 1 Figure 2
TOOLS REQUIRED
Wire Stripper
Blunt Nose (“Linesman”) Pliers
INSTALLATION INSTRUCTIONS
Read all instructions completely before beginning installation.
Step 1. Strip the three wire ends on power cord, approximately 1/2” from
the end.
Step 2. Connect the wires as shown in Figure 2. Twist wires together
using a pair of blunt nose (“linesman”) pliers, tightly, then twist each wire
nut on by hand. After twisting the connector on, hive each wire a tug, to
ensure it is secure. DO NOT wrap the “open” end of the connector with
electrical tape to cover. If bare wire is exposed outside the connector.
Instead of taping it, the connection should be redone.
Step 3. Ensure that all control switches are in the off position.
Step 4. Read WARNINGS then plug power cord into wall outlet.
Printed in U.S.A. © 2015 Innovative Hearth Products
P/N 900593-00 Rev. B 03/2017
IHP reserves the right to make changes at any time, without notice, in design, materials, specifications, and prices, and also to discontinue colors, styles, and products. Consult your local distributor
for fireplace code information.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
P/N 900593-00
Rev. B 03/2017
INSTALLATION INSTRUCTIONS FOR 120V POWER CORD KIT
[FIREPLACE MODELS: MPE-27-2, ERT3027, SPARK 27, CAPELLA 27, MPE-33-2, MPE-36-2, ERT3033, ERT3036, SPARK 33, SPARK 36, CAPELLA 33 AND CAPELLA 36]
POWER CORD KIT
HEARTH PRODUCTS
KITS AND ACCESSORIES
IHP
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
KIT CONTENTS
1 ea. Power Cord
1 ea. Cover Plate w/Cord Restraint
1 ea. Instruction Sheet
WARNING
• The power cord must not be pinched or against a sharp
edge. Secure cord to avoid tripping or snagging to reduce
the risk of fire, electric shock or personal injury.
• Do not run cord under carpeting. Do not cover cord with
throw rugs, runners or the like. Arrange cord away from
traffic areas and where it will not be tripped over.
• Power cord must plug into a dedicated circuit that is prop-
erly grounded (3-prong), fused (15 Amp.) and polarized
110/120 Volt, 60 Hz outlet only. Note: A dedicated circuit
is required to prevent overloading a house circuit in cases
of having multiple appliances on the same circuit. Use an
outlet that is protected by a ground fault circuit interrupter
where required by electrical code.
• Avoid the use of an extension cord which may overheat
and cause a risk of fire. However, if an extension cord is
used, the cord shall be number 14 AWG minimum size and
rated not less than 1800 Watts, 15 Amps. The extension
cord must be a three-wire cord with grounding type plug
and cord connection.
Power Cord Kit
Cat. No. Model Description
H1645 PCK Power Cord Kit
-
1
Astria Fireplaces Capella Series Instruction Sheet
- Type
- Instruction Sheet
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Matsushita MPE-33R User manual
-
Lennox Hearth Products MPE-36R User manual
-
Superior Fireplaces ERT3036 Operating instructions
-
FMI MPE-33R User manual
-
-
-
Lennox MPE-36R User manual
-
-
-
LG MPE-27 User manual
