Honda NC 700X Rear Carrier Owner's manual

Issue Date

INSTALLATION

INSTRUCTIONS

Accessory Application Publication No.

Honda Dealer: Please give a copy of these instructions to your customer.

PARTS LIST

87941-MGS-A300 1 of 7

REAR CARRIER

P/N 08L72-MGS-A30 NC700X/XD

Mll 13973

October 2012

No. Description Qty

(1) Rear carrier 1

(2) 8 mm socket bolt (short) 2

(3) 8 mm socket bolt (long) 2

(4) Collar (short) 2

(5) Collar (long) 2

(6) 8 mm flange nut 4

(7) Washer 4

(8) Cushion 4

(9) Safety label 1

TOOLS AND SUPPLIES REQUIRED

Box-end wrench (12 mm)

Hex wrench (5 mm)

File

Fret saw

Scissors

Ruler

Marker

Tape

Isopropyl alcohol

Shop towel

Torque wrench

No. Description Qty

(1) Right saddlebag bracket 1

(2) Left saddlebag bracket 1

(3) Plug 4

(4) Molding 1

REAR CARRIER/SADDLEBAG MOUNT BRACKETS

Sold separately

(1)

(2)

(3)

(4)

For the molding installation, refer to

the included Installation Instructions.

(8) (1)

(2)

(3)

(4)

(5)

(7)

(6)

(9)

2 of 7 87941-MGS-A300

USE AND CARE INFORMATION

The weight of the cargo must not exceed the •

following maximum weight capacity:

Maximum Weight Capacity

Rear carrier 22 lb (10 kg)

Check the accessory mounts frequently and •

retighten if necessary.

INSTALLATION INFORMATION

NOTE:

The Rear Carrier/Saddlebag Brackets which are sold •

separately are required to install this accessory.

Heat the bonding surfaces with a hair dryer if the •

ambient air temperature is below 70°F (21°C).

The adhesive reaches full strength in 72 hours. Wait •

at least 24 hours before riding your motorcycle.

Take care not to damage the painted surfaces of the •

motorcycle.

When the motorcycle is already equipped with the •

Rear Carrier/Saddlebag Brackets, loosen all its

mounting bolts before installing this accessory.

Item N·m kgf·m Ibf·ft

8 mm flange nut 27 2.8 20

Motorcycle’s 8 mm socket bolt 30 3.1 22

TORQUE CHART

Tighten all screws, bolts, and nuts to their specified

torque values. Refer to the Service Manual for the torque

values of the removed parts.

INSTALLATION

1. Refer to the Service Manual for the motorcycle,

remove the seats.

BOLT

NUT

FLANGE

COLLAR

SINGLE SEAT

PASSENGER

SEAT

SPRING

WASHER

CLIP

PASSENGER SEAT HINGE

87941-MGS-A300

3. Remove the passenger seat hinge as shown.

RIGHT GRAB RAIL

(Save)

PASSENGER SEAT

HINGE

WASHER

CLIP

RIGHT GRAB RAIL

LEFT GRAB RAIL

(Save)

CAP

(save)

WASHER

FLANGE

COLLAR

2. Refer to the Service Manual for the motorcycle,

remove the right and left grab rails.

MOTORCYCLE’S

8 mm SOCKET BOLT

MOTORCYCLE’S

8 mm SOCKET BOLT

4. Refer to the Service Manual for the motorcycle,

remove the seat cowl.

BOLT

CLIP

SEAT COWL

4 of 7 87941-MGS-A300

5. Cut and attach the template to the seat cowl and

mark it using a marker as shown.

SEAT COWL

TAPE

RIGHT SIDE:

LEFT SIDE:

SEAT COWL

TEMPLATE

(Reverse side)

TEMPLATE

MARKER

Repeat on

the left side.

6. Remove the template. Cut out the shaded areas on

the seat cowl as shown.

Repeat on the left side.•

FILE

File off the cut surfaces after

removing the area.

SEAT COWL

Remove any burrs.

FRET SAW

Remove.

7. Install the seat cowl in the reverse order of removal.

Remove.

87941-MGS-A300

8. Install the passenger seat hinge as shown.

RIGHT SADDLEBAG

BRACKET

PASSENGER SEAT

HINGE (Reuse)

WASHERS

(Reuse)

CLIP

(Reuse)

CUSHION

9. Loosely install the saddlebag brackets as shown.

Do not install the plugs yet.•

RIGHT SADDLEBAG

BRACKET LEFT SADDLEBAG

BRACKET

FLANGE COLLAR

(Reuse)

WASHER

(Reuse)

MOTORCYCLE’S

8 mm SOCKET

BOLT (Reuse)

MOTORCYCLE’S 8 mm

SOCKET BOLT (Reuse)

PLUG

Install after

tightening the

bolt securely.

REAR

CARRIER

10. Loosely install the rear carrier as shown.

8 mm

SOCKET

BOLT (long)

8 mm SOCKET

BOLT (short)

WASHER

COLLAR

(long)

COLLAR

(short)

8 mm FLANGE NUT

13. Install the cushions at the positions shown.

11. Tighten all loosely installed hardware to the

specifications in the torque chart.

12. Install the removed parts in the reverse order of

removal.

CUSHION

6 of 7 87941-MGS-A300

SAFETY LABEL

Remove the adhesive

backing before attaching.

14. Attach the safety label in the position shown.

ISOPROPYL ALCOHOL

Thoroughly clean the area where

the safety label will be attached.

REAR CARRIER

10 mm

SAFETY LABEL

3 mm

87941-MGS-A300

Cut off along the dotted line.

Align with the

contour of the

seat cowl.

Align with the contour

of the seat cowl.

Align with the contour

of the seat cowl.

Mark along

the template.

Mark along

the template.

Mark along

the template.

First, mark the right side seat cowl.•

Turn the template over to mark the •

left side seat cowl.

Cut this area when used on the left side.•

SCALE

NOTICE

If you print this template from your local computer, make

sure the printer settings do not “scale” or “shrink” the page.

Honda NC 700X Rear Carrier Owner's manual

Honda NC 700X Rear Carrier Owner's manual

Related papers

Other documents