Jenn-Air CCG2422 Installation Instructions Manual

Brand: Jenn-Air

Model: CCG2422

Category: Cookers

Type: Installation Instructions Manual

This manual is also suitable for

CCG2522

SEALEOGAScooroPs I c mJENN'AIR.1

CCG2422 AND CCG2522 3036 SHADELAND INDIANAPOLIS,IN46226-0901J

I SPECIAL WARNING: Improperinstallation, adjustment,alteration, service, maintenance oruse of

appliance can resultin serious injury orproperty damage.

IMPORTANT: Dimensions Shown in Both Inches and Centimeters. 30" MODEL

NOTICE TO INSTALLER: Leave these instructionswith the appliance.

NOTICE TO CONSUMER: Retain theseinstructions for future reference.

.911e",.=...__/76.2cm

1.43 cm

Entrance Min.

37h_. 2%"

8.73cmj_,_ _ _ _ ,i 6.67cm

I I-

f_MANIFOLD I

I ENTRANCEI

,',,S"27;;°

4,21 cm

IMPORTANT: Besuretheappliancebeing instafled isequipped for 'thegas to besupplied. Referto serial plateonundersideofbumer

box for this information,Do not attempt to convert this appliancefor use with a gas other than thetype specified.

36" M()DEL

NOTICE TO INSTALLER: Leave these instructions with the appliance.

NOTICE TO CONSUMER: Retain these instructions for future reference.

36"

9he"

37/1(

673cm_,r_r,_, _ _ j_ 25/_.

6.67 cm

I I-

-- _'_c'_- MANIFOLD . "_-

I EN'rFIANCE

•i 14"

1lS/_.• 36.57cm _.

4.05cm

IMPORTANT: Be sure the appliance being installed is equipped for the gastobe supplied.Refer to sedal plate onunderside of burner

box for this information. Do not attempt to convert this appliance for usewith a gas other than the typespecified.

IMPORTANT

CUTOUT

DIMENSIONS

ARE

CRITICAL 12/95

LOCATION OF YOUR JENN-AIR APPLIANCE IMPORTANT PREPARATION SUGGESTIONS

Locatethis appliance away from combustiblematerials such as win- 1. Chamferall exposededgesofdecorativelaminateto preventdam-

dow curtains and combustible wall decorations,agefrom chipping.

2. Radiuscomersof cutout and file to insuresmooth edgesand pre-

Minimum horizontal clearance between the edge of theapplianceand vent corner cracking.

combustible construction extending from the cooking surface to 16" 3. Rough edges, insidecorners which have not been rounded and

(45.72cm) abovethecooking surface is forced fits can contributeto cracking of the countertop laminate.

4. Countertop must be supported within 3" (7.62 cm) of cutout.

1" (2.54 cm) at rear

2" (5.08 cm) atsidesINSTALLATION OF APPLIANCE:

Theinstallationof thisappliancemustconformwithlocalcodesor, in

(Dimensionsapplyto both30"and 36"widemodels) theabsence oflocalcodes,withtheNationalFuel GasCode, ANSI

Z223.1--Latest Edition,or, in Canada, CAN/CGA-B149 Installation

Fig. 1 _".............. [". Code, LatestEdition.

'! _ This appliance,wheninstalled,mustbe electricallygrounded inaccor-

l"cm) 7,__ __,.

_T__ji18" dance withlocal codesor,inthe absenceoflocalcodes,withtheNa-

(2.54

145.72cm) tionalElectricalCodeANSI/NFPANo.70--Latest Edition,or,in Canada,

currentCSA Standard C22.1Canadian Electrical Code,Part 1.

-- All supply piping,except as noted, should usecommon National Pipe

T-(" "

'\ _ Thread (N.P.T.). Forall pipe connectionsuse an approved pipe joint

(3.811v2"Min.cm) (5.082"cm)'--__"compoundresistantto theactionofLP gas.

CAUTION: WarrantyisvoidonJenn-Airequipmentinstalledotherthan

INSTALLINGCABINETRY OVER YOUR asrecommendedby manufacturer.

JENN-AIR COOKTOP This applianceis designedfor usewiththe appliancegas pressure

A= 30"(76.2 cm) minimumvertical clearancebetween cookingsur- regulatorsuppliedwiththisappliance.Itmustbeinstalledinthegasway

faceandconstructionabovetheappliance.Thisclearancemay beahead ofthegas manifoldentrance.Itispresetforusewithnaturalgas

reducedto not lessthan24 inches(60.96 cm) by protectingtheand mustbe converted,as describedon page 6,for usewithLP gas.

undersideofthecombustiblematerialor metalcabinetabovethe(see Fig. 10 and 11.)

cookingsurfacewith not less than1/4 inch(.635 cm) insulating

mitlboardcoveredwith sheetmetalnotlessthan0.0122 inchthick* This applianceis designedto operate at a pressureof 5 inches of

B = 13"(33.02 cm) maximumdepthofcabinetsinstalledabovecook- watercolumnon naturalgasor,ifconvertedfor usewithLP gas(pro-

paneorbutane),10 inchesofwatercolumn.Makesurethisapplianc

ingtop. _is suppliedwith and adjustedfor the type of gas for whichit is d_

signed.

This appliancewas adjusted at the factoryforusewithnatural gas. If,

Fig. 2at any time, this appliance isto beusedwith adifferenttype of gas, all

of theconversion adjustments described on pages 5 through 7 must

_-bemade byaqualifiedservicetechnicianbeforeattemptingto operate

A • B---,- the cooktop on that gas. Naturalgas shouldbesuppliedto theappli-

ance pressureregulatorat a linepressurebetween6 and 14 inchesof

watercolumnor, ifconvertedfor LPgas, between 11 and 14 inches.

I _ I WARNING: Ifthe line pressuresupplyingthe appliance pressure

I regulatorexceeds 14"W.C. (anygas), anexternal regulatormustbe

Avoid use of cabinetsabovecooktop for storagespaceto eliminateinstalled in the gas line ahead of the appliance regulator to reduce

associated potential hazards such as reaching over open flames, thepressureto no more than 14" W.C. Failureto do this can result

in malfunction and damageto the appliance.

PREPARATION OF COUNTERTOP Insurethis applianceisadjustedforthetype ofgas suppliedto it and

Thecountertopcutoutmustbepreparedaccordingtotheillustrationon that thegas supply pressureto the appliancepressureregulatoris

page1 oftheseinstructions, withinthe properpressurerange.

CAUTION: Cutout dimensionsarecritical. Dimensionsmustbe mea- • Ifthisisa 36"widemodel,or ifitisa 30"wide modelandnoother

suredandcut accuratelyto within + 1/16"(.159 cm) to ensure proper applianceisto beinstalledinthecabinetrybelowit, proceedas

fit. instructedunder paragraphI.

•Ifthisisa 30"widemodelanda Jenn-AirModelW3OXXXorW131

ElectricWallOvenistobeinstalledincabinetrybelow,proceedas

*Jenn-AirOver-the-Rangemicrowaveovens(model#M418 and M438) instructedunderparagraphII.

havebeen listedbyUL for useoverGas and ElectricRanges. When•Do notremoveprotectivecapfrompipestubat manifoldentranc,-

properlyinstalledata minimumheight of66 inches(167.64 cm) from untilreadyto joingassupplypipingto appliance.

thefloortothetop ofthe microwave,theclearancetothe cookingsur-

faceatthe centerwillbe 133Ainches(34.93 cm).NOTE: InCanada, gasutilizationcodesprohibit useofstreet elbows.

Use standardpipe elbowsand make modificationsto these instruc-

tionsas necessary.

I. IF NO OTHER APPLIANCE IS TO BE INSTALLED BELOW Joinel/2"NPTpipeeIbew(Iocanyavailable)tothemalethreadsatthemani-

THIS COOK'FOP foldentrance.Whenjoined,causetheopenthreadsoftheelbowtofaceto-

Jointheappliancepressureregulatorsuppliedwiththisappliancetotheen- wardtheleftsideoftheappliance.Installtheapplianceinitscountercutout,

trancethreadsoftheGasManifold.Theapplianceregulatorismarkedwitha

directionalarrowindicatingcorrectdirectionofgasflow.Ensuretheappliance Joina 1/2"NPT pipenippletotheelbowusinga pipesectionofsufficient

-egulatorisinstalledwiththearrowpointingtowardthegasmanifoldentrance, lengthto extend,horizontally,beyondtheleftsideofthewalloven. (Toac-

)htantheapplianceregulatorto20to30ft-lbsoftorque, complishthisitmaybenecessarytoextendthepipesectionintoadjacent

cabinetry.)Joinaddtiona 1/2"NPTebow(s)andpipenipples,as necessary,

IMPORTANT toaccomplishthefollowing:

INevertightentomorethan35ft-lbsoftorque.Alwaysuseanapprovedpipe

jointcompoundresistanttotheactionofLPgas. 1. Jointheoutletoftheappliancepressureregulatorsuppliedwiththisappli

ancetothemalethreadsofthenewlyinstalledgassupplypiping.Instal

Installtheappliancein itscountercutout,theapplianceregulatorina locationwhichwillbeaccessiblebesideor

belowthewall oven.Insuretheapplianceregulatoris installedwith its

Makethegasconnectiontotheinletoftheappliancepressureregulatorwith directionalarrowpointingin thedirection ofgasflow.Tightenthe appli-

1/2"malepipethreads, anteregulatorto 20to 30ft-lbsoftorque.

Installa manualshut-oftvalveinanaccassibIelocationinthegaslineahead I IMPORTANT I

oftheappliancepressureregulatorandexternaltothisappliancefortheput-INevertightentomorethan35 ft-lbsoftorque.Alwaysusean approved

poseofturningonorshuttingoffgastotheappliance, pipejointcompoundresistanttotheactionofLPgas.

Makeadditionalpipeconnectionsasnecessaryaheadoftheshut-offvalveto 2. Locateandjoina manualshut-oftvalveinanaccessiblelocationinthe

thegassupplysource.Assureallpipejointconnectionsaregastight,gaslineaheadoftheapplianceregulatorandexternaltotheappliancefor

thepurposeofturningonor shuttingoffgasto theappliance.

IMPORTANT I

Testelijointsforgasleakswitha soapandwatersoluticoorotheraccepted Makeadditionalpipeconnectionsasnecessaryaheadoftheshut-offvalvete

eakdetectionmeans.Nevertestforgasleakswithanopenflame,thegassupplysource.Assureallpipejointconnectionsare gastight.

ILLUSTRATIVE GAS SUPPLY PIPING IMPORTANT

Testalljointsforgasleakswithasoapendwatersolutionorotheraccepted

Fig. 3 leakdetectionmeans. Nevertestforgasleakswithanopenflame.

(NOOTHERAPPLIANCEBELOWCOOKTOP)

IILLUSTRATIVE GAS SUPPLY PIPING

BURNER BOX

(REAR OFAPPLIANCE)0h/ALLOVENINSTALLEDBELOW30=COOKTOP

Fig. 4

L_tJBURNER BOX

MANIFOLD

ENTRANCE/--i{--.- (REAROFAPPUANCE)

MANIFOLD

APPLIANCE -- ENTRANCE

PRESSURE /

REGULATOR

I I LEFT SIDE

iALLPIPEJOINTS]PIPINGPASSESTHROUGH

1/2"N.P.T./MANUAL .NIPPLES

Lengths

SHUTOFF I to,u_ I 112"N.P.T. I

ALLPIPE JOINTS

VALVE I

I APPU E MANOAL

PRESSURE SHUTOFF

REGULATOR VALVE

-OI E}-

--- -m"TO GAS _"GAS

ELBOW INLET L_INLET

APPROXIMATECROSS SECTION

PROFILEOF WALLOVEN

I1. IF THIS IS A 30" WIDE COOKTOP AND A JENN-AIR,

MODEL W30XXX OR W131, ELECTRICWALL OVEN Note,regardingFig.4,above:

I Forconveniencainserviceagreundjointunion(notshown:locaHyavail,

ISTO BE INSTALLED BELOW THIS COOKTOP. able)shouldbeincludedinthepipingillustratedin Fig.4, ina Ioca_o

mostpracticalfortheinstallation.Generally,apracticallocationisinth

NOTE1: Thisapplianceand itsgasandelectricalsupplysourcesmustbe cabinetbelowthisappliance,nearthemanifoldentrance,ratherthani:

installedbeforethewailovenisinstalled.Seeillustration(ElectdcalWiring anadjoiningcabinet.

formation- page4; Fig.6)forrecommendedelectricalsupplysourceIoca- • IfthealternativepipingmethodshowninFig,5 isselectedforthe instal,

ons. lation,nogroundjointunionisrequired.(Theflexibleapplianceconnec

totillustratedprovidestheunionjointsnecessaryforservicing.)When

NOTE2: Itmaybe necessarytoextendgassupplypipingforthisappliancedividingwallispresentanda flexibleconnectorisuseditisrecomrnendec

intoadjacentunder-ccuntercabinetrywhenawallovenisinstalledbelowthis forconvenience,inbothinstallationandservice,theflexibleconnector

appliance, itself,passthroughthedividingwall.Anyflexibleconnectorusedwiti'

this appliancemustsatisfyall requirementsstated In thetext ac

companyingFig,5.

ALTERNATIVEPIPING METHODS TO CONNECT PRESSURE TESTING

APPLIANCE TOGASSUPPLYThe appliance must beisolated from thegas supplypipingsystem byclosing

Unlessprohibitedbylocalcodes orordinances,anewA.G.A. -Certified,flex-its individualmanualshut-offvalve duringanypressuretestingofthegas sup-

iblemetalappliance connector may be usedto connectthis appliance to its ply pipingsystemat test pressures equalto orless than 1/2 PSIG (3.5 kPa).

gassupply.Theconnectormust havean internaldiameternotlessthan nominal

1/2"NPT pipeand be nomore than 5 feet in length. A1/2"NPT x 1/2" flareThis appliance, as well as its individualshut-offvalve, mustbedisconnected

unionadapter isrequiredat each end oftheflexibleconnector. If a flexiblefrom thegassupplypipingsystemduringany pressuretestingofthesystemat

connectorJsusedassurethatboththeapplJancepressureregulatorandmanualtest pressures inexcess of1/2 PSIG (3.5 kPa).

shut-offvalveare joined solidlyto other permanent hard piping (either gas

supply piping or the appliance manifold) so as to bephysicallystationary.When checkingapplianceregulatorfunction,makecertain pressureofnatum_"

See illustrationsbelow: gas supplyis between6 and 14 inches of water columnor, ifconvertedfor LP

gas, between11and 14 inches.

ILLUSTRATIVE ALTERNATIVE PIPING ELECTRICAL WIRING INFORMATION

This apHanceisequippedwitha groundedtypepowercord.A groundedoutlet

Fig. 5 mustbeprovided. _tisrecommended,for convenience,theoutletbelocated

(with reference to Fig.6) as inAorB, below:

A. Ifno other applianceisto be installed below this appliance:

within eithertheshaded area or thecrosshatched area shown in Fig.6,

B,Ifa Model W3OXXX or W131 electric ovenisto be installedbelow this

appliance,either:

1) withinthe cross hatchedarea ofFig.6, or,

I 2) withinan adjacent cabinet.

I I

-.q--App,anceFig.6

PressureReoul_t0rsupplied ,___2s/s.

Observedirectionality

utGasF0w :6.67 cm

i_Flare Pipe31/z"(8.89cm)wide 36"

Ftare Union Nipple

Union Adapt_r slats when a wall 91.44cm

Adaptor ovenisinstalledBe-

Elbowlow 30" /

Flexible IA

Appliance (5ft.rn_o_)

) CABINETBO'I-FOM1"

_DimensionA:

I I W3OXXX: 5Y_"(13.97cm)

orAdaptor Ifawall oven )stobeinstalledbelowthisapplianceand thecounter uNt's out/at

zI istobemountedwithinthecrosshatched area of Fig. 6:

Gas _-91-- AppliancePressure t) The cabinet's lowerfrontpanel,belowthe oven, must be made remov-

Shut-oft j(('_ _J_Regulator,supplied ableforaccessto theoutlet.

ObServe

Vat,s lirecUonality 2) A clearance hole forthe powercord's plug (11,_,,[3.18cm] diaisrecom-

I_olGasRow) mended) must be provided throughtheoven's floorsupportshelf and, if

½'NPTPipeI necessary, through the slats supportingthe shelf. The clearance hole

"91- stationary _should be locatedas near as practicaltothe rearoftheshelfand (ifthe

I_J supplypipe _ _' NPT oven is modelW3OXXX) as near as pracflcal tothe left rearcomer.

Pipe 3) When model W3OXXX ismounted below thisappliance,and ifthe power

Nipple outletfor thisappliance isto belocated in thecrosshatchedarea ofFig.

I6, itisrecommendedthe powercord beroutedthroughtheexternalver-

tical clearance channel at theleft rear ofthe oven. The channel'scress

Gas sectionisapproximately 4.2" x 2.25" (10.7 x 5.7 cm),extendingthe full

Shut-0ff

Valve heightoftheoven. (Model W131 provides a similar,but larger,vertical

channel nearthe center ofthe mainbackof the oven.)

_1-_' Iftheoutletisto be mountedineither a left or rightadjacent cabinet, a clear-

NFr

Pipe

Stationary ancehole,as describedabove, must be providedinthe dividingwall between

supplyppe thecabinets.Fig4; page 3, illustratesa typical (left side) dividing wall. The

clearancehole(notshownin Fig.4) can be (ocatedas isconvenientinthis left

CAUTION: Do not attempt to attach theflexible connectordirectly to an wallorin thecorresponding fightwall.

external pipethread. Connectionrequiresflareunionadapters.

IIMPORTANT

Testallconnections forgas leaks withasoap andwater solutionor other

accepted leak detectionmeans.Never testfor gasleaks withan open

flame.

In planningany installation,notethatthe free lengthofthisappliance'spower Step 5: LocatetheLP orificespudpackettaped tothe undersideofth_

cord,extendingbeyondapoint3_" (9.53 cm) left ofthe nominalcenter of the burner box. Thespuds arezinc-plated and have smallhum

rearwall oftheburnerbox, whenviewed fromthefront ofthe unit,isapproxi- bets stampedon the side. This number codesthe orificediem

mately46" (117 cm). eterand its correctburner location.The followingillustration

showcorrectLP orificespud locationfor 4burner and 5 burne

models,respectively.

WARNING

ELECTRICALGROUNDING INSTRUCTIONS INSTALLATION OF LP (ZINC-PLATED) ORIFICE

THIS APPLIANCE IS EQUIPPED WITH ATHREE PRONG GROUND-

ING PLUGFORYOUR PROTECTIONAGAINSTSHOCK HAZARDANDSPUDS

SHOULD BE PLUGGED DIRECTLYINTO A PROPERLYGROUNDED

RECEPTACLE.DO NOTCUTOR REMOVETHE GROUNDINGPRONG 4 Burner model (30" Wide)

FROMTHIS PLUG.Fig. 8

WARNING

THIS APPLIANCE MUST BE DISCONNECTED FROM ITS ELECTRI-

CALSUPPLYATTHE WALLRECEPTACLE BEFORE SERVICING THE

APPLIANCE.

CONVERTINGAPPLIANCE FOR USE WITH LP GAS

WARNING

Propane conversion is to be performed by a JENN-AIR AUTHORIZED

SERVICER (or other qualified agency) inaccordance with the O

manufacturer's instructionsand all codes and requirements oftheau-

thorityhaving jurisdiction. Failure to follow instructionscould resultin (_ (_

seriousinjuryor propertydamage. The qualifiedagency performingthis

workassumes responsibilityforthisconversion.

WARNING

Electricalpowerand gas mustbe turnedoffpriorto conversion.

is appliancewasadjustedat thefactoryfor usewith natural gas. Tocon-

,rtitforuse withLP gas (propane or butane),each ofthe following modifica-

,,onsmustbeperformed: 5 Burner Model (36" Wide)

A. Replace all orifice spuds Fig. 9

Step 1: Removethegrates and burner heads.

Step2: Withan adjustablewrench,unscrewand removethebrasscollar

nuts(Fig. 7).

Step 3: Trim a small pieceofmasking tapeto the sizeofa dimeand

affix itover the end of a 9/32"nutdriver.

Step 4: Firmlypress the nut driverover theorificespud (Fig. 7) and

loosenspudbyturningcounterclockwise.Carefullyliftnutdriver

out ofburnerthroat. Orifice spud shouldbe capturedinthe

recess. Repeat this step foreach burner.

Fig. 7 REMOVAL OF ORIFICE SPUD ©©©

BRASS

COLLAR

NUT "_(_iJ %2"NUTDRWER

PIECEOFMASKING

END Step 6: With the masking tapeet/ll in place in therecess of the rl

OF DRIVER driver,pressan LP odfice spud(zinc-plated) intothe recess:

I__ INDENTATION that itissnugly captured,

BURNERBASE Step 7: Carefully installthe orificespudinthe appropriate burnerthrc

by turningclockwise totighten,33ghtentoatorqueof 15 to

inch-lbs.

ORIFICESPUD Step 8: Replace cylindricalbrass collar nutsand tightentoa torque

of6Oin.-Ibs. Replace burear heads and grates.Index each

grate toits burner pan.

Step 9: Save the odfices removed from the appliance forfuture us_

Invertcap in appliancepressure regulator C. LowFlame Adjustment

(See Figures10and 11.) Withthe applianceinstalled,theappli- (See Figure 12):

ance regulatorshouldbe locatedas shownin Fig 3 or 4.Identify

the type ofappliance regulatorontheunit andfollowthe instruc-This applianceisshippedfromthefactorywithlowand mediumflame

tions intheappropriateillustration, settingsadjustedforuse withnatural gas, If furtheradjustment is

necessa_, orto readjustforusewith LP,proceedas follows:

CONVERSION OF MAXlTROLAPPLIANCE

PRESSURE REGULATOR 1. Lightburnerand set controlknobfor lowflame.

Fig, 10 APPLYDOWNWARD

FINGERPRESSURE 2. Removecontrol knobfromvalvestem.

ATDISCEDGESTO

R,_LPREPL_CEPIN/NCA_CAUTION: NEVER USEA METALBLADETO PRYKNOBOFF.

_ _ IF KNOBCANNOTBEEASILYREMOVED,TUCK THE FOLDS

CONVERTE APPLY8tDEWARD

__ _ CAP [,_FINGERPRESSUREv.,-_v_ OFACLOTH DISHTOWEL UNDER THE KNOBANDPULLTHE

_"ANDPIN,Jt_"_- TOREMOVEPiN _ TOWEL UPWARDWITH STEADY,EVEN PRESSURE.

NAT LP 3. Inserta slender,thin-bladescrewdriverintothe recessat centerof

_ __valvestemand engagebtadewithslotin adjustingscrew.

4. Turn canterstemadjustingscrewto set flamesize

... clockwiseto reduce

...counterclockwiseto increase.

5.Replacecontrolknobwhenadjustmentiscomp)eted.

Properadjustmentwillproducea stable, steadyblueflameofminimum

CONVERSION OF HARPER-WYMAN size. The finaladjustmentshouldbecheckedbyturningknobfromhigh

'ig. 11 APPLIANCE PRESSURE REGULATOR to lowseveraltimes withoutextinguishingthe flame.

Withaquarter,engage

_ 1 slotandrotatecap f/8 of Thisadjustment,at lowsetting,wNIautomaticallyprovidetheproperflame

_'=_,_--,=_ / a turncounterclockwise,size at medium setting.

_. " _to removecap, Turn cap

-install Fig. 12COUNTERCLOCKWISE

TO INCREASEFLAME

TO REDUCE

FLAME SIZE

VALVE

Natural Setting LP Setting STEM

After ConversionStepsA, B and C have been completed,checkthe INSTALLATION OF NATURALGAS (BRASS) ORIFICES SPUDS.

appearanceofeach burner'sflameat the Hi and Lo settingsagainst

Fig.13. Iftheflames appeartoolargeortoo small, revieweach stepto 4 BURNER MODEL (30" WIDE)

make sureitwas completedcorrectly.

FLAME APPEARANCE AT HI AND LO Fig.14

Fig. 13 _._.,

off

M_ oo

©©

TO CONVERT APPLIANCE FOR USE WITH

NATURAL GAS Fig. 15 s BURNER MODEL (36" WIDE)

IWARNING I

Electricalpowerand gasmustbeturnedoffpriorto conversion.

if this appliancehasbeen convertedfor usewith LPgas, each ofthe

lowingmodificationsmustbe performedto convertthe unitback to

_turalgas.

A. Replace all orifice spuds

PerformStepst through4 on page5.

appliancebefore itsconversionfor use with LP gas. Observethe

small numbers stamped on the sides of the spuds and notethe

correctbumer locationfor eachspudas shownin Figs. 14 and 15.

CompleteSteps6 through9 on page 5 to completetheinstallation

ofnaturalgas mainspudsintheircorrectionlocations.

Save the odficasremovedfromtheapplianceforfutureuse, They

willbe neededifthis applianceis again convertedfor use withLP

gas.

Invert cap inappliance pressure regulator, (See Figs.10 & 11.) Fig. 17

Withthe applianceinstalledthe applianceregulatorshouldbe Io-5 BURNER MODEL

catedas shownineitherFig3 or Fig4(page3). Identifythetype of _\

illustration.appliancersgulatorandfollow theinstructionsin the appropriate /_ (_ _

Adjust Low Flame as Instructed on Page 6 in Item C._ _ __ t

sr StepsA,Band C havebeencompleted,checktheappearanceof Burner Input Rates -All Gases (btu/hr)

;h burner'sflame at the Hi and Lo settingsagainst Fig. 13. Ifthe Location Hi Lo

nes appeartoo largeor too small,makesure all stepswerecom- Right Front 12,000 1,500

ted correctly. Right Rear 9,100 1,050

Center 6,500 830

Left Front 9,1001,050

JRNER IGNITION AND AUTO-REIGNITION Left Rear 10,500 1,500

isapplianceis equippedforelectronicauto-reignitionbymeansofa

_rkigniterlocatedat therear of each burner. The burnersarede-

ned to light at anyvalve rotationthat admitssufficientgas flowto

)port a flameand to automaticallyrelight followinga lossof flame

.=to a draft or other adverse condition. This feature is provided as a

wenience and isnot intendedasasafetyfeature.TOP GRATE PLACEMENT

The top grates onthis cooktophaveundersideprojectionlugsdesigned

LUTION:Never usea metalbladeto pryoffa controlknob.Ifa knob tonestinmatchingdepressionsinthespillovertrays. Duringgrateplace-

lnot beeasilyremovedtuckthefoldsofa cloth dishtowelunderand mentalwayspositiongratestomakethisengagement. Correct indexing

_undthe knoband pullthe towelupwardwithsteadyevenpressure, ofgratesabove burnerportswillpreservethegrates'appearanceand

helpassurelonglife.

LUTION: Never covercontrolknobsor surroundingcontrolsurface

h utensils,towelsor other objects.Never obstructfree air passage

stthecontrolknobs.Theknobopeningshavebeensized toproperly

ltrol air entryto theinterioroftheapplianceduringoperation.

isappliancehas noair shutters.Primary air adjustmentsare unnec-

;ary. The burnersare designedto provideoptimumaerationfor all

_es withoutair shutters.When operatingproperly,burnersshould

)duceclearly defined,even blueflames. Iftheflames have yellow

or arehazyandotherwiseappearto haveinsufficientair,obtainthe

"vicesofa qualifiedservicetechnician.

ecifiedinputratesare as shownin Figures16 and 17, below.

Fig.16

4 BURNER MODEL

Burner Input Rates - All Gases (btu/hr)

Location Hi Lo

Right Front12,000 1,500

Right Rear 9,100 1,050

Left Front 6,500 630

Left Rear 10,500 1,500

V LF

BK (RIBBED) N (NERVURE) SPARKMODULE REIG= ]3 = " AVG

G V _ MODULED'ALLUMAGE

BK (SMnDTH) N (LISSE) S_ __ __ R LR

_ _ _ , , _ _ Y ; = RR .

6 7 8 9101112 J AD

4 _ AVD

VALVE SVITCHES

CDNTACTERUSDE RDBINET

RF J_ BL

AVD /IGNITERS

BK RR /_ Y ALLUMEURS

NAD J

LR _ R

AG /

LF /j W ORIFICESPUDSIZES

AVG B TAILLESDESnRIFICES

RFIAVD iGG 105

RRIAD 140 89

WIRINGDIAGRAM210396A LF/AVG 118 74

PLANDEC_BLAGE LRIAG 156 99

CAUTIDN:Thiswlrln9 dlagromICor30'modelonly,

ATTENTII]N:Plan de c_blage pour [e modele de 30 po seulemen±,

IGNITERS

ALLUMEURS

BK (R]BBED) N (NERVURE) ]

I W LF

G V [ I, I) " " AVG

BK (SMnBTH) N(LISSE) _ _ _.

SPARK MODULE

MFIDULED'ALLUMAGE Y . =RR .

VALVE SVITCHES _ JAD "

CONTACTERUSDE RBBINET _ _

9 101112 13 14 15 16

RF /A N HIll IH I

AVD l N =

BK RR /_Y

N AD J i]

LR J_ R

LF _ W DRIFICESPUDSIZES

AVG B TAILLESDESDRIFICES

mmmmm JENN-AIR Burner/BrOteurRF/AVDN_t,G_s/Gez]66n_t, LP G_s/G_z105PL

RRIAD _nd LFIAVG 140 89

VIRINGDIAGRAM210397A CEN 118 74

PLANDE CABLAGE LR/AG 156 99

CAUTIF1N:This wiring dlagrom {or 36' model only,

ATTENTIFIN',Plan de c_blage pour le modele de 36 po seulement,

REQUIRED ADJUSTMENTS ATTIME OF INSTALLATION

The installationof this appliance must conform with local codes, or in the absenceof local codes, with

the latest edition of the National Fuel Gas Code ANSI Z223.1 USA or current CAN/CGA-B149

INSTALLATIONCODE.

_-_ Thisappliance was manufacturedforusewithNaturalGas. If LP gas isthefuel ofchoice,followthe

conversionto LPprocedurefound inthe installationinstructions.

Testall externalconnectionsfor gasleaks. Never test for gas leaks with an open flame.

---] Testall electrical connections.

Jenn-Air CCG2422 Installation Instructions Manual

Brand: Jenn-Air

Model: CCG2422

Category: Cookers

Type: Installation Instructions Manual

This manual is also suitable for

CCG2522

Download PDF

report

Jenn-Air CCG2422 Installation Instructions Manual

This manual is also suitable for

Jenn-Air CCG2422 Installation Instructions Manual

Related papers

Other documents