AEG DB8040-U User manual

STEAM IRON 5SAFETY™ MODEL DB 80xx

D • EL • NL • F • GB

AEG IFU 5Safety Mahe 19.07.11.indd 1 19.07.11 11:19

D Anleitung ..............................3–14

Vor der ersten Benutzung des

Bügeleisens lesen Sie bitte die

Sicherheitshinweise auf Seite 4 sorg-

fältig durch.

GR Βιβλίο οδηγιών...................3–14

Πριν χρησιμοποιήσετε για πρώτη

φορά το σίδερο, παρακαλούμε

διαβάστε τις υποδείξεις ασφαλείας

στη σελίδα 4.

GB Instruction book ............15–19

Before using the appliance for the

 rst time, please read the safety

advice on page 16 carefully.

NL Gebruiksaanwijzing ........3–14

Lees, voordat u het strijkijzer voor

de eerste keer gebruikt, zorgvuldig

het veiligheidsadvies op pagina 5.

F Mode d’emploi ..................3–14

Avant d'utiliser le fer pour la

première fois, veuillez lire attentive-

ment les consignes de sécurité

en page 5.

AEG IFU 5Safety Mahe 19.07.11.indd 2 19.07.11 11:19

Page is loading ...

15

D

EL

NL

F

GB

A

B

C

D

F

G

H/I

K

L

M

N

O

E

A. Soleplate

B. Maximum water level

indicator

C. Filling aperture with cover

D. Spray nozzle

E. Spray button

F. Steam jet button

G. Steam knob

H. Power indicator light

I. Safety auto-o light

K Mains cable

L. Temperature selector

M. Water tank

N. Cable wrap facility

O. Rubber-napped heel

Components

AEG IFU 5Safety Mahe 19.07.11.indd 15 19.07.11 11:19

16

GB

G

Safety advice

Read the following instruction

carefully before using machine for the

 rst time.

• This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience

and knowledge, unless they have

been given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

• Children should be supervised to

ensure that they do not play with the

appliance.

• The appliance may only be connected

to a power supply whose voltage

and frequency comply with the

speci cations on the rating plate!

• The iron is not to be used if it has been

dropped, if there are visible signs of

damage on the iron or its cord or if it is

leaking.

• The appliance must only be connected

to an earthed socket.

• If the appliance or the supply cord

is damaged, it must be replaced by

the manufacturer, its service agent or

similarly quali ed person, in order to

avoid hazard.

• The iron must be used and rested on a

stable surface. When placing the iron

on its stand, ensure that the surface on

which the stand is placed is stable.

• Never leave the appliance unattended

while connected to the supply mains.

• The appliance must be switched o

and the mains plug withdrawn each

time after use, before cleaning and

maintenance.

• The plug must be removed from

the socket outlet before the water

reservoir is  lled with water.

• The mains cable must not come into

contact with any hot parts of the

appliance.

• Do not immerse the appliance in

water or any other liquid.

• Do not exceed the maximum  lling

volume as indicated on the appliances.

• If there are limitations please de ne

water quality / type of water that can

be used with appliance.

• This appliance is intended for

domestic use only. The manufacturer

cannot accept any liability for possible

damage caused by improper or

incorrect use.

Ironing chart

Fabric Temperature setting Ironing recommendation

Acrylic

Dry iron on wrong side.

Acetate

Dry iron on wrong side while still damp or use spray to dampen.

Nylon & Polyester

Iron on wrong side while still damp or use spray to dampen.

Rayon

Iron on wrong side of fabric.

Viscose

Mainly dry iron. Steam can be used under manufacturer’s instructions.

Silk

Iron on wrong side. Use an ironing cloth to prevent shine marks.

Cotton blends

Check label and follow manufacturer’s instructions. Use setting fo the  bre

requiring lowest setting.

Wool & wool blends

Steam iron on wrong side or use ironing cloth.

Cotton

Dry iron while still damp or use spray to dampen. Use steam medium to

high.

Corduroy

Steam iron on wrong side or use ironing cloth.

Linen

to “max”

Iron on wrong side or use ironing cloth to prevent shine marks, especially

with dark colours. Dry iron while still damp or use spray to dampen. Use

steam medium to high.

Denim

to “max”

Use maximum steam.

Varied ironing speed and fabric dampness might cause optimal setting to di er from that recommended in the table!

AEG IFU 5Safety Mahe 19.07.11.indd 16 19.07.11 11:19

17

D

EL

NL

F

GB

1. Before  rst use. Remove all adhesive

remains and gently rub with a

dampened cloth. Rinse water tank

to remove foreign particles. When

turned on for the  rst time, temporary

vapours/odours may occur.

4. Using the steam function

(f

or models without auto steam).

Turn the steam knob to select the

desired steam output for each

garment, if selecting the o position,

it indicates ironing without steam, the

iron can be used as a dry-iron.

2. Filling steam iron with water.

M

ake sure plug is removed from

power outlet. Turn steam selector to

Dry setting and open  lling aperture

cover. Using beaker provided, pour

water up to maximum level. Close

cover.

5. For models with auto steam control

sy

stem the steam regulation is done

by the temperature selector. When

turning it to set temperature, it will

automatically adjust steam position,

as indicated on the knob. To stop the

steam and use as a dry-iron, press

down

. To come back to steam

function, press

again.

3. Plug power cable into a power

outlet. Power indicator light turns

on. Set temperature by turning

temperature selector to adequate

choice. When the light turns o , iron is

ready to be used.

GB

6. Using the spray mist and steam

jet function. Ensure that water tank

is at least 1/4 full. Use spray mist to

pre-dampen fabrics by pressing spray

button several times to release a  ne

mist (A). To use the steam jet function,

ensure that tank is at least 1/2 full.

Press steam jet button several times to

prime pump (B).

B

A

auto

clean

Getting started

AEG IFU 5Safety Mahe 19.07.11.indd 17 19.07.11 11:19

18

GB

G

Cleaning (do not use any detergent)

1. Always store iron on its heel rest.

Unplug the iron. To clean exterior

surfaces, use a damp soft cloth and

wipe dry. Do not use any chemical

solvents, as these will damage the

surface.

2. Auto clean function.

F

ill water up to 100ml. Plug the iron

and set the temperature to MAX.

When the light turns green, unplug,

hold it over a sink and pull the steam

knob out (for EDB8040 set the steam

knob to auto-clean). Gently shake until

all water is gone. Insert the steam

knob back and press until the click.

Turn the iron on to dry the soleplate.

⚠

If the temperature knob is not on

MAX position, it will not be possible to

pull out or place back the steam knob.

3. Cleaning the soleplate. Do not use

sc

ouring pads or harsh cleaners on the

soleplate as these will damage the

surface. To remove burnt residue, iron

over a damp cloth while iron is still

hot. To clean the Glissium™ soleplate

(enamelled), simply wipe with soft

damp cloth and wipe dry.

Getting started

7. Steaming hanging items. Vertical

steam jet function is ideal for steaming

curtains, suits and delicate fabrics.

Hang item on a hanger, hold iron at a

distance of 10–20 cm and press steam

jet button.

8. 3-way Auto-OFF. If iron is left

unattended on soleplate or on the

side, it turns o after 30 seconds. If left

unattended on the heel, it turns o

after 8 minutes. To turn on, just begin

to iron again.

AEG IFU 5Safety Mahe 19.07.11.indd 18 19.07.11 11:19

19

D

EL

NL

F

GB

Disposal

Packaging materials

The packaging materials are environ-

mentally friendly and can be recycled.

The plastic components are identi ed by

markings, e.g. >PE<, >PS<, etc.

Please dispose the packaging materials

in the appropriate container at the

community waste disposal facilities.

Old appliance

The symbol

on the product or on

its packaging indicates that this product

may not be treated as household waste.

Instead it shall be handed over to the

applicable collection point for the

recycling of electrical and electronic

equipment. By ensuring this product

is disposed of correctly, you will help

prevent potential negative consequences

for the environment and human health,

which could otherwise be caused by

inappropriate waste handling of this

product. For more detailed information

about recycling of this product, please

contact your local city o ce, your

household waste disposal service or the

shop where you purchased the product.

Troubleshooting

Problem Possible cause Solution

Soleplate is not heating even though iron is

turned on.

Connection problem Check main power supply cable, plug and

outlet.

Temperature control is in MIN position. Select adequate temperature.

Iron does not produce steam. Not enough water in tank. Fill water tank (see “Getting started”, no 2).

Steam control is selected in non-steam position. Set steam control between positions of

minimum steam and maximum steam (see

“Ironing chart”).

Spray function does not work. Not enough water in tank. Fill water tank (see “Getting started”, no 2).

Steam jet and vertical steam jet function does

not work.

Steam jet function was used very frequently

within a short period.

Put iron on horizontal position and wait

before using steam jet function.

Iron is not hot enough. Adjust the proper temperature to steam

ironing (up to

). Put iron in vertical

position and wait until temperature indicator

light turns o .

Water leaks from the soleplate during ironing. The iron is not hot enough. Set the temperature dial to a temperature

(

to maximum) suitable for steam ironing.

Put the iron on its heel and wait until the light

has gone out before you start ironing.

Flakes and impurities come out of the

soleplate during ironing.

You have used hard water, which has caused

scale  akes to develop in the water tank.

Use the self-clean function one or more times.

Water leaks from the soleplate while the iron is

cooling down or after it has been stored.

The iron has been put in horizontal position

while there is still water in the water tank.

Empty the water tank and set the steam

control to position o before storing the iron.

AEG IFU 5Safety Mahe 19.07.11.indd 19 19.07.11 11:19

3485 A DB80xx 02020711

♻

Printed on recycled paper

Electrolux Hausgeräte Vertriebs GmbH

Fürther Strasse 246

D-90429 Nürnberg

Germany

www.aeg-home.com

AEG IFU 5Safety Mahe 19.07.11.indd 20 19.07.11 11:19

AEG DB8040-U User manual

This manual is also suitable for

AEG DB8040-U User manual

in other languages

Related papers

Other documents