AEG 66300KF-ANU44 User manual

66300KF-an

Glaskeramik-Kochfeld

Ceramic glass hob

Table de cuisson vitrocéramique

Montage- und Gebrauchsanweisung

Installation and Operating Instructions

Instructions de montage et mode d’emploi

Page is loading ...

36

Dear customer,

Please read these operating instructions carefully.

Pay particular attention to the section “Safety information” on the first

few pages. Please retain these operating instructions for later refer-

ence. Pass them on to possible new owners of the appliance.

The following symbols are used in the text:

1 Safety instructions

Warning: Information concerning your personal safety.

Important: Information on how to avoid damaging the appliance.

3 Information and practical tips

2 Environmental information

1. These numbers indicate step by step how to use the appliance.

2. …

3. …

These operating instructions contain information on steps you can take

yourself to rectify a possible malfunction. Refer to the section “What to

do if...”.

In the event of any technical problems please contact your nearest cus-

tomer service centre at any time. (Addresses and telephone numbers

may be found in the appendix under "Customer Service Centres“).

You should also refer to the section "Service".

Printed on recycled paper.

Thinking ecologically means acting ecologically …

37

Contents

Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Description of the Appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Cooking zones and control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Digital displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Safety cut-out function for the cooking zones . . . . . . . . . . . . . . . . . . . . . . . 43

Before Using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Initial Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Operating the hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Touch control sensor panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Switching on the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Switching off the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Heat settings selecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Keep warm setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Switching the triple ring zone on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Switching the casserole zone on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Switching off a cooking zone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Residual Heat Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Cooking using the automatic warm up function . . . . . . . . . . . . . . . . . . . . . . 49

Cooking without the automatic warm up function. . . . . . . . . . . . . . . . . . . . 50

Child safety lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Blocking/unblocking the control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Uses, Tables and Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Pans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Advice on Cooking with and without Automatic Warm up . . . . . . . . . . . . . 59

Settings for Cooking on the Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Metal décor strips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

What to do if … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Rectifying faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

38

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Regulations, Standards, Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Safety Instructions for the Installer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Electrical Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

39

Operating Instructions

1 Safety

The safety aspects of this appliance comply with accepted technical

standards and the German Appliance Safety Law. However, as manufac-

turers we also believe it is our responsibility to familiarise you with the

following safety instructions.

Electrical Safety

• The installation and connection of the new appliance must only be

carried out by qualified personnel.

• Repairs to the appliance are only to be carried out by approved serv-

ice engineers. Repairs carried out by inexperienced persons may cause

injury or serious malfunctioning. If your appliance needs repairing,

please contact your local customer center or your dealer.

3 Please follow these instructions, otherwise the warranty will not cover

any damage that may occur.

• Flush-mounted appliances may only be operated following installa-

tion in suitable installation cabinets and workplaces which conform

to the relevant standards. This ensures sufficient protection against

contact for electrical units as required by the VDE [Association of

German Electrical Engineers].

• If your appliance malfunctions or if fractures, cracks or splits appear:

– switch off all cooking zones,

– disconnect the hob from the electricity supply.

Child Safety

The cooking zones will become hot when you cook. Therefore, always

keep small children away from the appliance.

40

Safety During Use

• This appliance may only be used for normal cooking and frying in the

home. It is not designed for commercial or industrial purposes.

• Do not use the hob to heat the room.

• Take care when plugging electric appliances into mains sockets near

the hob. Connection leads must not come into contact with the hot

surface.

• Overheated fats and oils catch fire quickly. You should supervise

cooking when preparing foods in fat or oil (e.g. chips).

• Switch off the cooking zones after use.

Safety When Cleaning

• For safety reasons do not clean the appliance with a steam jet or high

pressure cleaner.

• Clean the hob in accordance with the maintenance and cleaning in-

structions in this manual.

How to avoid damage to the appliance

• Do not use the cooking area as a worktop or storage space.

• The frameless edge of the glass ceramic surface is susceptible to

knocks. Please be careful when moving pots and pans around.

• Do not have the cook zones on with empty pans, or with no pots or

pans on them.

• Ceramic glass is very tough, and impervious to sharp temperature

changes, but is not unbreakable. It can be damaged if particularly

hard or sharp objects fall on to it.

• Do not use pots made of cast iron, or which have damaged bases with

rough edges or burrs. Moving these around may cause scratches.

• If sugar or a mixture containing sugar falls onto a hot cooking zone

and melts, remove immediately, while still hot, using a kitchen scrap-

er. If left to cool down, it may damage the surface when removed.

• Keep objects or materials liable to melt away from the ceramic glass

surface, for example, artificial materials, aluminium foil, or cooking

wraps. If any other materials or foodstuffs are melting on the ceramic

glass surface, these should also be cleaned away immediately, using a

kitchen scraper.

41

2 Disposal

Disposing of the packaging material

All materials used can be fully recycled.

Plastics are marked as follows:

• >PE< for polyethylene, as used for the outer wrapping and the bags

inside.

• >PS< for polystyrene foam, e.g., as used for the padding materials.

They are completely free of CFCs.

Disposal of old appliances

1 Warning: Before disposing of old appliances please make them inoper-

able so that they cannot be the source of danger.

To do this, disconnect the appliance from the mains supply and re-

move the mains lead.

To protect the environment, it is important that worn out appliances

are disposed of in the correct manner.

• The appliance must not be disposed of with household rubbish.

• You can obtain information about collection dates or public refuse

disposal sites from your local refuse department or council.

42

Description of the Appliance

Cooking zones and control panel

Triple ring cooking zone

2300W

Single ring cooking zone

1200W

Single ring cooking zone

1200W

Control panel

Casserole zone

2400W

Cooking setting

selector

„Block“

sensor panel

Three-ring sensor panel

Sensor panel

”On/Off”

“Timer” with

control indicators

Browning zone sensor panel

Cooking setting

selector

Three-ring control lamps

Browning zone control lamp

Indicator for cooking setting/ residual warmth

43

Digital displays

The four display panels that belong to the four cooking zones indicate:

– ¾ after having been switched on,

– u when a keep warm setting has been selected,

– ¿ to Ç, depending on the cooking setting selected,

– 2 to 6 (with decimal point) for intermediate cooking settings,

– a when the automatic warm up function is in operation,

– h when there is residual warmth,

– l when the child safety device has been switched on,

– e when there is a malfunction

1 Safety cut-out function for the cooking zones

If one of the cooking zones is not switched off after a certain period of

time or the cooking setting is not altered, that particular cooking zone

will automatically switch itself off.

Any residual warmth will be indicated with h (as for “hot”) in the dig-

ital displays corresponding to the particular cooking zones.

The cooking zones switch themselves off when:

3 Should one or more cooking zones switch themselves off before the pe-

riods of time indicated have elapsed, see the chapter “What to do if …”.

Other causes for a cooking zone switching itself off

All cooking zones will immediately switch themselves off if liquid boils

over and lands on the control panel.

The same thing will happen if you place a damp cloth on the control

panel. In both instances, after the liquid or cloth has been removed, the

appliance will need to be switched on again using the main switch I.

• Cooking setting u, 1 - 2 after 6 hours

• Cooking setting 3 - 4 after 5 hours

• Cooking setting 5 after 4 hours

• Cooking setting 6 - 9 after 1.5 hours

44

Before Using for the first time

Initial Cleaning

Wipe the ceramic glass surface with a damp cloth.

1 Important: Do not use any caustic, abrasive cleaners! The surface could

be damaged.

Operating the hob

Touch control sensor panels

To operate the touch control sensor panels, touch the desired panel

with the tip of your pointed finger until the relevant displays illuminate

or go out, or until the desired function is carried out.

3 Ensure that you are only touching one sensor panel when operating the

appliance. If you finger is too flat on the panel, the sensor panel below

may be actuated as well.

Switching on the appliance

The entire appliance is switched on using the ”On/Off” sensor panel

I.

Touch the “On/Off” sensor panel for approx. two seconds.

The digital displays will show ¾.

3 After the “On/Off” sensor panel has been actuated to switch on your

appliance, a cooking setting must be selected for a cooking zone within

approx. 10 seconds, or a time must be set using the timer (egg timer

function). If not, the appliance will switch itself off again for reasons

related to safety.

45

Switching off the appliance

To completely switch off the appliance, actuate the “On/Off” sensor

panel I.

Touch the “On/Off” sensor panel for approx. one second.

3 After switching off a single cooking zone or the entire cooking surface,

the existing residual warmth will be displayed in the digital displays of

the corresponding cooking zones in the form of h (for “hot”).

Heat settings selecting

For setting and changing the heat setting (u to Ç) for the selected

cooking zone.

Raise the heat setting using the heat setting selector sensor panel .

Lower the heat setting using the heat setting selector sensor panel .

46

Keep warm setting

Each of the 4 cooking zones has a keep warm setting u.

Use the heat setting selector sensor panel to set the keep warm set-

ting u.

Switching the triple ring zone on and off

According to the size of the saucepan or frying pan, when using the tri-

ple ring cooking zone you can switch from a smaller cooking zone to a

larger cooking zone using the “triple ring zone” sensor panel.

3 You can only switch to the next size if a heat setting has already been

set for the smaller heating ring.

1. Set the desired heat setting.

2. Touch the “triple ring” sensor panel.

This will switch the setting to the centre heating ring. The lower control

lamp will illuminate.

47

3. Touch the “triple ring” sensor panel to activate the outer heating ring.

The upper control lamp will illuminate.

4. To switch off the outer heating ring, touch the “triple ring” sensor pan-

el, and the heating ring that is outermost at the time will switch off.

Switching the casserole zone on and off

1. Set the desired heat setting.

2. To switch the casserole zone on or off, place your finger flat on the

“casserole zone” sensor field until the indicator light illuminates or goes

off.

48

Switching off a cooking zone

1. To switch off a cooking zone touch the heat setting selector sensor

panel and simultaneously, or return the setting to zero using the

heat setting selector sensor panel .

Residual Heat Indicator

When an individual cooking zone or the entire hob is

switched off, any residual heat is shown with an h (for

“Hot”) in the digital display for the appropriate cooking

zones.

Even after the cooking zone has been switched off, the

residual heat indicator only goes out when the cooking zone is cold.

2 You can use the residual heat for melting and keeping food warm.

1 Important! As long as the residual heat indicator is illuminated, there

is a risk of burns.

1 Important! If the power supply is interrupted the h symbol will also

go out and information about residual heat will no longer be available.

However, it is still possible to burn yourself. This can be avoided by tak-

ing care around the hob.

49

Cooking using the automatic warm up function

All of the cooking surface’s four cooking zones can be adjusted to any

of nine settings, and are equipped with an automatic warm up func-

tion:

– ¿, lowest heat setting

– Ç, highest heat setting

– a, automatic warm up function.

When you select the desired heat setting using the heat setting se-

lector sensor panel, the cooking zone will operate at maximum power

for a certain period of time and will then automatically switch back to

the follow-on heat setting that has been set.

The length of time that the automatic warm up function operates de-

pends on the follow-on heat setting selected.

1. Touch the heat setting selector sensor panel to set the desired heat

setting from ¿ to Æ. The heat setting that has been set will then be

displayed. After a period of 5 seconds, the a (=automatic warm up

function) will appear in the display in place of the heat setting. After

the warm up period has finished, the heat setting will once more be

displayed.

3 If you should choose a higher heat setting while the automatic func-

tion is in operation, e.g. from Á to Ã, the period of time that the warm

up function is in operation will be adjusted accordingly. If you select a

lower setting, the warm up period will end immediately.

You can cook using the automatic warm up function only if the cook-

ing zone is cold or moderately warm. If a cooking zone is already hot

when you switch it on (h indicator), the automatic warm up function

cannot be used.

50

Cooking without the automatic warm up function

If you wish to use the cooking zones without the automatic warm up

function, select the desired heat setting using the heat setting selector

sensor panel .

1. Touch the heat setting selector sensor panel in order to set the de-

sired heat setting from Ç to ¿.

3 You can change the setting at any time using the heat setting selector

sensor panels and .

51

Child safety lock

You can use the child safety lock to safeguard against unwanted use of

the cooking surface.

Switching on the child safety lock

To be able to switch on the child safety lock the appliance must be

switched on, but all the cooking zones must be switched off.

1. Touch the sensor field for approx. three seconds.

An acoustic signal will sound as confirmation.

2. Touch any heat setting sensor field .

l will appear in the displays, and the child safety lock is activated. The

appliance will switch itself off automatically after a few seconds.

52

Overriding the child safety lock

The child safety lock can be overridden in order to use the appliance

(until the appliance is switched off again). When the appliance is

switched on again the child safety device is activated once again.

1. Switch on the appliance.

When the child safety device has been activated, l will be displayed.

2. Touch any two heat setting sensor fields and simultaneously.

An acoustic signal will sound as confirmation. The child safety device

has been overridden until the appliance is switched off, and the cook-

ing surface can be used as normal.

53

Switching off the child safety lock

1. Switch on the appliance.

When the child safety device has been activated, l will be displayed.

2. Touch the sensor field for approx. three seconds.

An acoustic signal will sound as confirmation.

3. Touch any heat setting sensor field .

The displays will become dark, and the child safety device is switched

off. The appliance will switch itself off automatically after a few sec-

onds.

54

Timer

There are two ways to use the timer:

– as a safety cut-out function. Set a cooking period for a cooking

zone, and after this time has elapsed the cooking zone will automati-

cally switch itself off. This function can be used for more than one

cooking zone simultaneously.

– as a countdown timer without a cut-out function (“egg timer”),

whereby an acoustic signal can be heard after the set period of time

has elapsed.

3 The countdown timer cannot be used if a cooking zone is switched on.

Safety cut-out

The cooking zone(s) for which you want to use the safety cut-out func-

tion must be switched on.

1. Using the timer sensor panel, select the cooking zone for which the

safety cut-out is to be set.

By touching the timer sensor panel once the first active cooking zone is

selected in a clockwise direction, and the corresponding control lamp

will flash rapidly. Hereby the (e.g.) left rear control lamp corresponds to

the left rear cooking zone. 00 will appear in the timer display.

The next active cooking zone is selected by touching the timer sensor

panel again.

Page is loading ...

AEG 66300KF-ANU44 User manual

AEG 66300KF-ANU44 User manual

in other languages

Related papers

Other documents