Jung-pumpen Jung Pumpen Multifree Submersible Solids Handling Pump Owner's manual

Installation/Operation/Parts

For further operating, installation,

or maintenance assistance:

Call 1-800-642-5930

English.......... Pages 2-12

Installation/Fonctionnement/Pièces

Pour plus de renseignements

concernant l’utilisation, l’installation ou

l’entretien :

Composer le 1-800-642-5930

Français ....... Pages 13-23

Instalación/Operación/Piezas

Para mayor información sobre el

funcionamiento, instalación o

mantenimiento de la bomba:

Llame al 1-800-642-5930

Español ....... Páginas 24-34

INSTALLATION AND OPERATOR’S MANUAL

MULTIFREE™ Submersible Solids

Handling Pump

MANUEL D’INSTALLATION ET DE L’OPÉRATEUR

Pompe submersible pour matières

solides MULTIFREE™

MANUAL DE INSTALACIÓN Y DEL OPERARIO

Bomba sumergible para el manejo de

partículas sólidas de MULTIFREE™

293 Wright St., Delavan, WI 53115

Phone: 1-800-642-5930

Orders Fax: 1-800-426-9446

Web Site: jungpumpen-us.com

Safety 2

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation, operation, and maintenance of the product.

Save this manual for future reference.

This is the safety alert symbol. When you see this

symbol on your pump or in this manual, look for one of

the following signal words and be alert to the potential

for personal injury!

indicates a hazard which, if not avoided, will

result in death or serious injury.

indicates a hazard which, if not avoided,

could result in death or serious injury.

indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE

addresses practices not related to personal injury.

The manufacturer cannot anticipate every possible

circumstance that might involve a hazard. The warnings

in this manual, and the tags and decals affixed to the unit

are, therefore, not all-inclusive. If you use a procedure

or operating technique that the manufacturer does not

specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that

the procedure or operating technique that you choose

does not render the system unsafe.

Electrically powered sewage pumps normally give many

years of trouble-free service when correctly installed,

maintained, and used. However, unusual circumstances

(interruption of power to the pump, large solids in

the sump, flooding that exceeds the pump’s capacity,

electrical or mechanical failure in the pump, etc.) may

prevent your pump from functioning normally. To prevent

possible damage, consult your dealer about installing

a secondary sewage pump or a high water alarm. See

Troubleshooting in this manual for information about

common sewage pump problems and remedies. For

more information, see your retailer, call Jung Pumpen

customer service at 1-800-642-5930 or visit our web site

at jungpumpen-us.com.

Risk of electric shock. Can shock, burn or

kill. Sh

ock can cause serious injury or death. Failure to

follow the warnings below can result in fatal electric shock.

Risk of electric shock. Can shock, burn or

kill. During operation the pump is in water:

• Checkyourlocalcodesbeforeinstalling.You

must comply with their rules. Only qualified

personnel should install the pump and associated

controlequipment.

• Groundthepumpaccordingtoallapplicablecodes

and ordinances.

• Takecarewhenchangingfusesorresettingthe

circuit breaker. Disconnect power to the pump

before servicing. Do not stand in water when

working on the control box or with the circuit

breaker panel.

• Thispumpisintendedforpermanentconnection

only. Do not connect conduit to pump. Provide a

strain relief at the control box for the power supply

cord connection to box. All control components

must be UL or CSA listed and suitable for end

useapplication.

• Donotremovecordorstrainrelief.Donotliftthe

pump by the power cord (See ‘Cord Lift Warning’).

Contents

Important Safety Instructions .......................2

Installation .......................................3

Electrical ........................................ 4

Control Panels ................................... 5

Operation ........................................5

Maintenance ......................................6

Lubrication ...................................... 6

Repair Parts ......................................8

Troubleshooting .................................10

Product Specifications ............................11

Warranty .......................................11

Safety • Installation 3

Risk of burns. Motors can operate at high

temperatures. To avoid burns when servicing the pump,

allow it to cool for 20 minutes after shut-down before

handling it.

Risk of explosion and hazardous gas.

Septic system must be vented in accordance with local

plumbing codes.

•

Do not smoke or use sparkable electrical devices or

flame in a septic (gaseous) or possible septic sump.

• Ifasepticsumpconditionexistsandifentryinto

sump is necessary, then (1) provide proper safety

precautions per OSHA requirements and (2) do

not enter sump until these precautions are strictly

adhered to.

• Donotinstallthepumpinanylocationclassifiedas

hazardous by National Electrical Code, ANSI/NFPA

70-1984.

Wear safety glasses at all times when working with the

pump.

Do not run the pump dry. Dry running can overheat the

pump and will void the warranty.

The pump requires periodic maintenance. Check

the oil level and for water in the oil, as described in

Maintenance.

Provide a means of pressure relief for pumps whose

discharge line can be shut-off or obstructed.

The pump is frost-resistant to –4°F (–20°C) when stored

in dry conditions. It must not be allowed to freeze in

water after installation.

Installation

Handle with care. Check the items received against

the packing list to be sure that all equipment has been

received. Inspect the pump for shipping damage. If any is

found, file a claim with the carrier immediately.

Thank you for purchasing this Jung Pumpen product. To

help ensure years of trouble-free operation, please read

the manual carefully.

This pump may be installed on an optional guide-rail lift-

out system for ease of inspection and service. Otherwise,

install the pump on a hard, level (cement, asphalt, etc.)

surface. Never place the pump directly on earth, clay,

sand, or gravel surfaces. An optional leg kit is available.

The basin or pit must be at least 24” (60 cm) in diameter

and 30” (76 cm) deep. Reduce the number of bends in

the discharge piping to keep the outlet flow as smooth

as possible. Full dimensional information is found in

Product Specifications.

Install the pump as a free-standing unit, with a pipe

union in the discharge piping to allow removal for

servicing. Figure 1depicts a typical sewage pump in an

ordinary pit.

The discharge piping must not be smaller than the pump

discharge. The pump must always be lifted by the lift-out

chain or cable and never by the power supply cable. See

Cord Lift Warning.

6262 0910

Risk of electrical shock and fire.

1. Attempting to lift or support the pump by

the power cord can damage cord and cord

connections, expose bare wires, and cause a

fire or electrical shock.

2. Use handle on top of pump for all lifting or

lowering of pump. Disconnect the power

to the pump before doing any work on it or

attempting to remove it from the pit.

3. Lifting or supporting the pump by the power

cord will void the warranty.

Risk of electrical shock.

Can burn or kill.

Do not lift pump by power

cord.

WARNING

Cord Lift Warning

Figure 1: Typical free-standing installation

Installation 4

Mounting the pump on guide rails permits easy

inspection and service in permanent installations. Use

the installation instructions supplied with the guide rail

lift-out system. Place the pump opposite the influent

opening to prevent stagnant areas where solids can settle.

See Figure 2.

Electrical

Risk of electric shock. Can shock, burn or

kill. When installing, operating, or servicing this pump,

follow electrical safety instructions. Only trained service

personnel should install or service this pump.

1. DO NOT splice the power cord and never lay the

cable ends in water.

2. DO NOT handle or service the pump while it is

connected to the power supply.

3. DO NOT operate the pump unless it is properly

grounded. Wire the pump directly into a grounded

terminal block in an automatic float or pump

controller box for automatic operation. Connect

the pump according to all applicable codes. For

continuous operation, wire the pump directly into

the switch box.

4. Incorrect voltage can cause a fire or seriously

damage the motor and voids the warranty. Make

sure that the frequency and voltage shown on the

nameplate corresponds to the frequency and voltage

of the electrical supply. The supply voltage must be

within + 10% of the nameplate voltage. If in doubt

consult a licensed electrician.

5. Connect the pump to its own dedicated circuit with

no other load on the circuit. Figures 3, 4 & 5 show

single and three phase wiring schemes.

Figure 2: Typical installation with guide rail system for

permanent locations.

U1/Z1 blackU1/Z1 black

Z2 blue

Z2 white

U2 red

Th

HaHi

15

34

6

22U1/Z

1U23

032

32 blue

32 white

30 white

30 orange

Motor Thermal

Protector

Interconnect Plug

Figure 3: Single phase wiring diagram

Motor Thermal

Protector

Interconnect Plug

U1 black

V1 blue

U2 grey (grey)

V2 grey (white)

W2 grey (brown)

V1 white

W1 red

15346

(L1)

T1

(L2)

T2

(L3)

T3

X

30 32

32 blue

32 white

30 white 30 orange

Figure 4: Three phase star configuration wiring diagram

Motor Thermal

Protector

Interconnect Plug

M or h

Pro c

I r t Plu

U1 black

U1 bl c

U2 grey ( ey)

V2 ey (whi )

W rey b wn)

W1 red

W1 ed

1534

30 hite 3 r nge

U1 blackU1 black

V1 blue

U2 grey (grey)

V2 grey (white)

W2 grey (brown)

V1 white

W1 redW1 red

15346

(L1)

T1

(L2)

T2

(L3)

T3 30 32

32 blue32 white

30 white 30 orange

Figure 5: Three phase delta configuration wiring diagram

Installation • Operation 5

6. Use a control panel sized to match the pump. Refer

to control panel installation instructions for wiring

connection information.

7. Install the pump in accordance with all electrical

codes that apply. Install a fused disconnect switch or

circuit breaker in accordance with local codes.

8. Any alterations to internal pump circuitry must be

made using crimp connectors and professional tools.

9. The pump rotation must be clockwise (

– viewed

from the top of the pump). NEVER operate it

inreverse.

If a three phase unit runs backwards, interchange

two of the three power supply wires to reverse the

motor’s direction of rotation.

Control Panels

Risk of electric shock. Can shock, burn or

kill.Groundpumpandmotorbeforeconnectingcontrols

or power supply. Adhere to local electrical codes

governing pump and control installations.

A control panel is not included with the pump. Install

a simplex or duplex control panel (purchase separately)

for proper pump operation. Single phase pumps require

a start package, as shown in Product Specifications. A

full range of controls and switches are available from

yourdealer.

If a Jung Pumpen control panel is not used, install a

control panel with circuit breaker or fused disconnect

as required by local code. Use magnetic starters with

ambient compensated overload protection. Three phase

units require three line protection; single phase units

require only one line protection. Inadequate protection

voids the warranty.

Co ntrol Panel Overload Adjustment –

Three Phase

NOTICE: See your con trol panel in stallation and

operating instructions before adjusting overload setting.

Set the overload protective device to the nameplate full

load current.

Size the overload protective device so that the trip

current is 115% of the nameplate full load current.

Operation

Risk of cuts and possible unexpected starts.

Rotation of the cutter with hands in the cutter area can

cause loss of fingers.

Disconnect the electrical power and

keep your hands away from the pump inlet opening when

working on or handling the pump for any reason. Do not

use automatic reset controls with this pump.

Single phase units have an automatic overload protector

in the motor which will protect the motor from burning

out due to overheating/overloading. When the motor

cools down, the overload protector will automatically

reset and start the motor. This can happen at any time.

Three phase units require external overload protection.

If the overload trips frequently, check for the cause. It

could be:

• stuckimpeller

• wrong/lowvoltage

• badthermaloverloadprotector

• electricalfailureinthemotor.Ifthemotorhas

electrically failed, replace the pump.

NOTICE: Normal domestic sewage will cause very little

dulling or wear of the pump parts. However, pumping

abrasives (such as fine sand) will increase wear and

tear and may make it necessary to replace certain

pumpcomponents.

The pump is not equipped with thermostats or a leak

sensor probe. Check the oil condition in the seal

chamber quarterly in heavy duty service or annually in

light duty service.

NOTICE: Failure to monitor the oil condition voids the

warranty. Motors damaged by flooding of the motor

cavity due to seal or O-Ring failure may not be covered

under warranty.

Verify the capacity of the pump by checking the

discharge. Verify that the pump is free from any vibration

and noise.

To avoid overheating the motor for continuous operation,

the pump must be completely submerged in liquid. Set

the level switches to maintain this submerged condition.

Do not allow the pump to run in a dry sump. It will void

the warranty and may damage the pump.

Maintenance 6

Maintenance

Only qualified mechanics with proper tools and

knowledge should attempt to service this pump.

Heavy parts. Use lifting gear of appropriate

capacity positioned directly over lift point(s).

Seal Lubrication

Oil in the seal chamber should be changed after the first

300operating hours, then each 1000 hours thereafter or

annually. The oil fill/oil drain opening is labled “OHL”.

After cleaning and sanitizing the pump, drain all oil and

residue into a clean measuring container.

• Iftheoilismilkyinappearance,itiscontaminated

with water. Refill pump with clean, fresh oil, using

amounts and type shown in Maintenance. Check oil

condition again after 300 operating hours.

• Iftheoiliscontaminatedwithbothwaterand

pollutants, the main seal must be replaced and

the oil changed. Recheck oil condition after

300operating hours.

NOTICE: Whenever the main seal is being serviced,

remove oil and replace with new oil at reassembly. Use

only SAE 5W-15W (ISO 22-44) mineral oil.

The filling quantity is shown in Product Specifications.

NOTICE: Fill oil reservoir with the exact quantity of oil

specified. The pump will become inoperable if overfilled.

Cleaning the Impeller

Risk of electrical shock, cuts, and possible

unexpected starts.

Disconnect the electrical power and

keep your hands away from the pump inlet opening when

working on or handling the pump for any reason. Do not

use automatic reset controls with this pump.

1. Disconnect the electrical power supply.

2. Disconnect the discharge piping (this step is not

necessary if you have a guide-rail lift-out system).

3. Hoist the pump out of the pit using the lift-out

system or the lifting chain (not the cord) and place

the pump in a suitable area where it can be cleaned.

4. Remove all scale and deposits from the pump. Check

visual appearance of all pump housing screws and

mating surfaces. Tighten any loose fasteners.

Risk of infection. Pathogens (such

as hepatitis) can collect on pump during normal

operation. Submerge the complete pump in a

disinfectant solution (dilute chlorine bleach) for at

least one hour before disassembly.

5. Unscrew four 5 mm Allen screws attaching the

volute and remove the volute casing. It may be

necessary to tap around the parting line with a lead

or rawhide hammer to loosen the casing.

Risk of cuts. Wear protective gloves.

Worn impellers can have sharp edges that could cut

or scratch.

6. Carefully clean the impeller and volute surfaces.

Inspect for obvious cracks or damage.

7. Reverse step 5 to reassemble the pump.

Impeller Replacement

1. Remove four 5 mm Allen screws that attach the

volute and remove the volute casing. It may be

necessary to tap around the parting line with a lead

or rawhide hammer to loosen the casing.

Risk of cuts and possible unexpected

starts. Wear protective gloves. Worn impellers can

have sharp edges that could cut or scratch.

2. Wedge the impeller with a piece of wood and

loosen the central impeller screw located in the

impellerhub.

3. Loosen the impeller by striking it gently with a lead

or rawhide hammer, then slide it off the motor shaft.

4. Clean all exposed surfaces, including motor shaft.

5. Greasetheshaftcoverontheinside.DONOTuse

grease containing graphite (like Molykote).

6. Assemble all impeller-mounting components and

tighten finger tight.

7. Slide a new impeller over impeller mount.

8. Set impeller-to-motor housing gap (X) to .007”

(2mm). See Figure 6.

9. Block impeller with a piece of wood and tighten

central impeller screw to 48 ft-lb (65 Nm).

10. Attach motor unit to volute casing. Finger tighten

four 5 mm Allen screws, then torque each to

5.9ft-lb (8 Nm). The cable entry point is opposite the

discharge opening.

X

Figure 6: Impeller clearance

Maintenance 7

Main Seal Replacement

1. Follow steps 1 through 4 under “Cleaning

theImpeller”.

2. Follow steps 1 through 4 under

“ImpellerReplacement”.

3. Lay the pump on its side and remove the oil plug

from the bracket. Drain oil into a clean container

and check for water in the oil and for pollutants in

the oil.

NOTICE: Water is heavier than oil. Look for water at

the bottom of the oil. It will appear as tiny bubbles.

If there is water present in the oil, the shaft seal or

the O-Ring will need to be replaced. If there is no

water present in the oil, the shaft seal and O-Ring do

not need replacing.

4. Remove the two 8 mm capscrews that hold the

motor housing to the bracket. Tap around the parting

line with a lead hammer or rawhide mallet to loosen

the motor housing. Remove the motor housing from

the bracket.

5. Remove the oil seal and oil seal bushing from the

motor housing.

6. Remove the motor housing O-Ring and clean the

O-Ring groove.

7. Remove the seal retaining ring from the

motorhousing.

NOTICE:

The shaft seal consists of 5 parts - the upper

and lower silicon carbide seals, two rotating silicon

carbide seals, and the spring. Be sure that you do not

scratch or mar the shaft when removing the seals. If the

shaft is marred, it must be dressed smooth with fine

emery or crocus cloth before installing new seal. Do

not reduce the shaft diameter.

8.

Pull and turn the rotating seal halves to remove them

from the motor shaft. If necessary, use a flat blade

screwdriver to help pry the seals from the shaft.

9. Unscrew four capscrews and remove the bracket

from the motor housing.

10. Use a flat blade screwdriver and very carefully pry

the lower seal half from the cavity.

11. Use a flat blade screwdriver and very carefully pry

the upper seal half from the bracket cavity.

Installing the New Shaft Seal

NOTICE: Install all new O-Rings, seals, and gaskets

during reassembly. It is good practice to replace the

O-Rings each time the pump is serviced.

1. Clean the seal cavities in the bracket and

motorhousing.

2. Lubricate the seals with a very small amount of

cleanoil.

3. Inspect the shaft for nicks and scratches.

4. With finger pressure only, press the stationary seal

halves firmly and squarely into the seal cavities in

the bracket and motor housing.

NOTICE: Be sure you do not scratch the seal surface.

5. Reinstall the lower seal retaining ring.

6. Reinstall the bracket on the motor. Use a new

O-Ring. Torque 8 mm capscrews to 48 ft-lb (65Nm).

7.

Slide the rotating seals and the spring onto the shaft.

NOTICE: Be sure you do not scratch the seal surface.

Be careful that the shaft shoulder does not damage

the seal faces when they are passing over the shaft.

Make certain the polished surfaces of the rotating

seals face the mating surfaces of the stationary

sealhalves.

8. Clean the O-Ring groove in the bracket and install a

new O-Ring.

NOTICE: It is good practice to replace the O-Rings

each time the pump is serviced.

9. Reinstall the volute casing on the bracket. Torque

four Allen screws to 5.9 ft-lb (8 Nm).

10. Greasetheshaftcoverontheinside.DONOTuse

grease containing graphite

11. Assemble all impeller-mounting components and

tighten finger tight.

12. Slide impeller over impeller mount.

13. Set impeller-to-motor housing gap to .007” (2mm).

See Figure 6.

14. Block impeller with a piece of wood and torque

central impeller screw to 48 ft-lb (65 Nm).

15. Attach motor unit to volute casing. Torque four Allen

screws to 5.9 ft-lb (8 Nm).

16. Refill pump with specified amount of fresh, clean oil.

Do not overfill.

17. Position pump vertically and check for free

impellerrotation.

The pump is ready to return to service.

Repair Parts 8

1

2

8

3

7

4

3

Repair Parts 9

Item # -> 1 2 3 4 7 8

Model Housing with

stator

Rotor Seal Set* Volute Casing Impeller Cord & Cord Entry

25’ 50’ 100’

V1D-01

RP-JP43648 RP-JP44220

RP-JP22032 RP-JP43055

RP-JP43091

RP-JP43063 RP-JP43701 RP-JP43702

V1D-21

V1D-03 RP-JP43644

RP-JP21754V1D-23 RP-JP43910

V1D-43 RP-JP43645

V15D-01

RP-JP43649 RP-JP43654

RP-JP43249

V15D-21

V15D-03 RP-JP43644

RP-JP21754V15D-23 RP-JP43910

V15D-43 RP-JP43645

V2D-01

RP-JP43649 RP-JP43654

RP-JP43092

V2D-21

V2D-03 RP-JP43644

RP-JP21754V2D-23 RP-JP43910

V2D-43 RP-JP43645

V3D-01

RP-JP43650 RP-JP43363 RP-JP43990 RP-JP43868 RP-JP43869 RP-JP43870

V3D-21

V3D-03 RP-JP43646

RP-JP21757 RP-JP21800 RP-JP43063 RP-JP43701

RP-JP43702

V3D-23 RP-JP43911

V3D-43 RP-JP43647

V5D-43 RP-JP43902 RP-JP22733

RP-JP22851 RP-JP43937

RP-JP43873

RP-JP43061 RP-JP43701

V7D-43 RP-JP43903 RP-JP22734 RP-JP43875

* Seal Set includes all O-rings, shaft cover, supporting washer, rotary shaft seal and mechanical seal to service entire pump.

Troubleshooting 10

Risk of electric shock. Can shock, burn or

kill. Disconnect power before attempting any service or

repair work on pump.

Risk of cuts and possible unexpected starts.

Keep hands away from pump suction inlet when working

on or servicing pump.

Symptom Possible Cause(s) Corrective Action

Motor not running Motor protector tripped. Allow motor to cool. Make sure pump is completely submerged. Clear debris from volute

and impeller. Check for high amp draw.

Open circuit breaker or blown fuse. Replace fuse or reset breaker. If circuit breaker opens repeatedly, don’t reset it - call a

licensed electrician.

Impeller clogged or binding. Check amp draw. If it is more than twice the nameplate amps, the impeller is locked.

Bearings and shaft may be damaged. DISCONNECT POWER, clear debris from volute,

impeller, and cutter as needed.

Power cable damaged. Resistance between power cable and ground should be infinity. If any reading is less than

infinity, call a licensed electrician.

Bad control panel. Inspect control panel wiring. Call a licensed electrician.

Defective liquid level switch. With switch disconnected from power, check continuity through switch while activating

liquid level switch. Replace switch if necessary.

Not enough liquid in wet well to activate

controls.

Allow the liquid to rise several inches above the switch-on level.

Liquid level cords tangled Untangle cords for free operation.

Automatic controls defective Try running pump in manual mode. If it runs, the automatic control is at fault.

Pump runs continuously Liquid level control cords tangled Untangle cords for free operation.

Pump is airlocked. Stop pump for about one minute, then restart. Repeat stopping and starting until the

airlock clears. If the airlock persists, DISCONNECT POWER, pull the pump and drill a

1/8” hole in the discharge pipe between the pump discharge and the check valve.

Flow in matches or exceeds the pump’s

capacity.

A larger pump or more pumps may be needed.

Little or no effluent

delivered from pump

Check valve plugged, stuck shut, or

installed backwards.

Make sure check valve is installed correctly (flow arrow should point away from pump)

and functioning correctly.

System head excessive. Consult dealer.

Pump suction plugged. DISCONNECT POWER, pull pump, inspect, and clear as needed.

Wrong voltage or not wired correctly. Check pump’s rotation; check nameplate voltage against supply voltage (they must

match); consult a licensed electrician.

Pump is air locked. Stop pump for about one minute, then restart. Repeat stopping and starting until the

airlock clears. If the airlock persists, DISCONNECT POWER, pull the pump and drill a

1/8” hole in the discharge pipe between the pump discharge and the check valve.

Worn or damaged impeller. DISCONNECT POWER, pull pump and inspect impeller. Replace if necessary.

Liquid level controls incorrectly installed

or defective.

Reposition or replace as necessary.

Pump cycles constantly No discharge check valve installed. Install discharge check valve.

Discharge check valve stuck open. Repair or replace check valve as necessary.

Sewage wetwell too small. Consult dealer.

Liquid level controls incorrectly installed

or defective.

Reposition or replace as necessary.

Pump too small for inlet flow. Consult dealer about larger pump or second pump.

Warranty • Product Specifications 11

Model HP PHASE Frequency Voltage* F.L.C. R.P.M. Max. head Max. flow rate Weight

†

Cable SOOW START PAK

Hz Volts Amp 1/min ft m GPM LPM lbs kg

V1D-01

1

60

200 9

1680

16 5 264 999

108 49 12/6AWG12

SPGV-7

V1D-03 3 1685 Not Required

V1D-21 1

230

8 1680 SPGV-8

V1D-23

3

6.2

1685 Not Required

V1D-43 460 3.5

V15D-01

1.5

1

200

13.3

1675 23 7 352 1332

SPGV-9

V15D-03 3 9.7 Not Required

V15D-21 1

230

11.6 SPGV-10

V15D-23

3

7.4

Not Required

V15D-43 460 4

V2D-01

2

1

200

17.2 1650

31 9 396 1499

SPGV-11

V2D-03 3 10.7 1620 Not Required

V2D-21 1

230

15.5 1675 SPGV-12

V2D-23

3

8.7

1620 Not Required

V2D-43 460 4.6

V3D-01

3

1

200

20.5 1720 36 11

484 1832 117 53

10/6AWG10 SPGV-13

V3D-03 3 13.6 1670 39 12 12/6AWG12 Not Required

V3D-21 1

230

18.5 1720 36 11 10/6AWG10 SPGV-14

V3D-23

3

12.5

1670 39 12

12/6AWG12 Not Required

V3D-43

460

7

V5D-43

‡

5 10.2 1680 44 13 660 2498 249 113

V7D-43

‡

7.5 12.3 1670 52 16 748 2831 258 117

* Input voltage ±10%

† Weight with 25ft (7.6m) cable. Add 7lb (3.2kg) for each additional 25ft (7.6m).

‡ Oil chamber capacity is 61in

3

(1000cc) except for V5D and V7D, which is 103.7in

3

(1700cc)

Limited Warranty

Jung Pumpen warrants to the original consumer purchaser (“Purchaser” or “You”) of Jung Pumpen Effluent Pumps, Sewage Pumps, and Package

Systems, that they will be free from defects in material and workmanship for the Warranty Period of 12 months from date of manufacture.

Our warranty will not apply to any product that, in our sole judgement, has been subject to negligence, misapplication, improper installation, or

improper maintenance. Without limiting the foregoing, operating a three phase motor with single phase power through a phase converter will void the

warranty. Note also that three phase motors must be protected by three-leg, ambient compensated, extra-quick trip overload relays of the recommended

size or the warranty is void.

Your only remedy, and Jung Pumpen’s only duty, is that Jung Pumpen repair or replace defective products (at Jung Pumpen’s choice). You must pay all

labor and shipping charges associated with this warranty and must request warranty service through the installing dealer or selling distributor as soon

as a problem is discovered. No request for service will be accepted if received after the Warranty Period has expired. This warranty is not transferable.

EXCEPTIONS: Special Application Pumps, Filtered Effluent Pumps, Grinder Pumps, 2-1/2” Sewage Pumps, and Lift Systems are warranted for a period

of 12 months from date of purchase or 18 months from date of manufacture, whichever comes first.

Jung Pumpen SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.

THE FOREGOING LIMITED WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING BUT

NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE FOREGOING LIMITED

WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION EXPRESSLY PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on the duration of an implied warranty, so the

above limitations or exclusions may not apply to You. This warranty gives You specific legal rights and You may also have other rights which vary from

state to state.

This Limited Warranty is effective June 1, 2011 and replaces all undated warranties and warranties dated before June 1, 2011.

Jung Pumpen

293 Wright Street, Delavan, WI 53115

Phone: 800-642-5930 • jungpumpen-us.com