Simplicity 040450-00 User manual

Not for

Reproduction

80005284 Rev. B

Pages 2-5 and 10-12

Option 1 and Option 2

Pages 2 and 7-12

Option 1 and Option 2

en

Installation and Operation Manual

Wireless Monitor Kit

Questions?

Help is just a moment away!

Call: Technical Services 800-743-4115

Monday-Friday 8:00 AM to 5:00 PM Central Time

Milwaukee, WI USA. All Rights Reserve.

Option 1

Control Panel is equipped with an ON BOARD

RADIO.

Option 2

Two fresh AA 1.5V batteries are

required. Batteries not included.

Two fresh AA 1.5V batteries are

required. Batteries not included.

OFF BOARD RADIO to be installed on

Control Panel.

Note: Grommet is not used on every

assembly.

Note: Grommet is not used on every assembly.

fr

esen

Lorem ipsum

Not for

Reproduction

Thank you

for purchasing this standby generator

accessory. When installed in accordance with the

instructions that follow, this Wireless Monitor Kit will

provide years of dependable service. After installation

keep your purchase receipt and this Installation

Instructions with your generator operator’s manual.

Record the dealer name and phone number on the

monitor label.

Safety

Failure to read and follow the safety warnings and

instructions in this document and in the operator’s

manual could result in death, serious injury, and/or

property damage.

The warnings and instructions must be read,

understood, and followed when setting-up, operating,

servicing, transporting, or storing the unit.

WARNING

Certain components in this product

and related accessories contain

chemicals known to the State of

California to cause cancer, birth

defects, or other reproductive harm.

Wash hands after handling.

WARNING

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired

operation.

Only current licensed electrical professionals should

attempt installation of this accessory. Installation must

strictly comply with all applicable codes, industry

standards and regulations.

2

DEALER NAME ________

DEALER PHONE _______

The safety alert symbol is used to identify

safety information about hazards that can result in

personal injury. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to indicate the

likelihood and the potential severity of injury. In addition,

a hazard symbol

may be used to

represent the type

of hazard.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING

indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION

indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE: indicates a situation that could result in

damage to the product.

Not for

Reproduction

Preparation

Installation

Before performing any generator maintenance, always

perform the following steps:

1 Set the generator’s circuit breaker to its OFF

position.

2 Press and hold the control panel OFF button.

3 Remove 15 Amp fuse from control panel.

4 Utility voltage is present at generator control

panel. Disconnect power before servicing control

panel by removing the fuses from the transfer

switch.

1 Remove the five screws and roof.

2 Assemble antenna piece to base.

3 Install grommet on antenna wire.

4 Insert grommet and wire into slot on rear panel.

5 Attach antenna (temporarily) onto the back panel.

3

1

2

3

4

1

2

4

3

5

en

Not for

Reproduction

7 Insert the antenna wire to the ON BOARD RADIO

wire until it clicks. Route wire away from sharp

objects and secure with ties.

6 If the wire connection cannot be found, locate by

removing the four screws used to attach the control

panel.

Option 1

Control Panel is equipped with an ON BOARD

RADIO.

7

4

8 Reinstall the roof.

9 Mount the antenna to the top of the roof.

9

8

6

After installation has been completed, replace fuses in

transfer switch, replace 15 Amp fuse in control panel,

and set generator circuit breaker to its ON position.

Go to: LINK MONITOR WITH GENERATOR.

A wire connection is available at the inside cabinet

electrical harness hole.

Not for

Reproduction

Option 2

OFF BOARD RADIO to be installed.

6 Remove screws on control panel and

tilt panel forward.

7 Prepare the OFF BOARD RADIO mounting surface

by cleaning with an alcohol wipe or other cleaning

solution. Make sure surface is dry before

proceeding to Step 8.

11

8 Remove RED plastic from adhesive on OFF

BOARD RADIO. Attach radio to inside wall under

control panel. Press down firmly.

9 Plug connector into control panel as shown.

10 Insert wire for antenna through side panel harness

hole.

11 Reinstall control panel and tighten screws securely.

12 Insert antenna wire to the OFF BOARD RADIO wire

until it clicks. Route wire away from sharp objects

and wire tie

13 Reinstall the roof.

14 Mount the antenna to the top of the roof.

After installation has been completed, replace fuses in

transfer switch, replace 15 Amp fuse in control panel,

and set generator circuit breaker to its ON position.

Go to: LINK MONITOR WITH GENERATOR.

12

5

8

10

9

6

14

13

7

en

Page is loading ...

Not for

Reproduction

Preparation

Installation

Before performing any generator maintenance, always

perform the following steps:

1 Set the generator’s circuit breaker to its OFF

position.

2 Press and hold the control panel OFF button.

3 Remove 15 Amp fuse from control panel.

4 Utility voltage is present at generator control

panel. Disconnect power before servicing control

panel by removing the fuses from the transfer

switch.

1 Remove the four screws attaching the control panel.

2 Locate the ON BOARD RADIO wire connection.

4

2

1

3

Option 1

Control Panel is equipped with an ON BOARD

RADIO

GENERATOR READY

GENERATOR POWER

SERVICE NEEDED

SYSTEM UPDATE

Generator Systems

2

Kit parts required:

7

en

Not for

Reproduction

3 Insert the antenna wire through inside cabinet hole

and around the backside as shown.

4 Fasten the four screws attaching the control panel

5 Assemble antenna piece to base.

6 Loosen inside roof bolt in corner.

7 Mount the antenna to the top of the roof. While

lifting roof in corner, lay antenna wire in space

between rubber gaskets.

8 Insert antenna wire to the ON BOARD RADIO wire

until it clicks. Route wire away from sharp objects

and wire tie.

9 Tighten roof bolt (6) securely.

3

4

After installation has been completed, replace fuses in

transfer switch, replace 15 Amp fuse in control panel,

and set generator circuit breaker to its ON position.

Go to: LINK MONITOR WITH GENERATOR.

8

Option 2

OFF BOARD RADIO to be installed.

GENERATOR READY

GENERATOR POWER

SERVICE NEEDED

SYSTEM UPDATE

1

Remove the four screws attaching the control panel.

2 Prepare the mounting surface by cleaning with an

alcohol wipe or other cleaning solution. Make sure

surface is dry before proceeding to Step 3.

1

2

8

5

7

6

7/16

Kit parts required:

Not for

Reproduction

3 Remove RED plastic from adhesive on OFF

BOARD RADIO. Attach radio to inside wall under

control panel. Press down firmly.

4 Insert the antenna wire through inside cabinet hole

and around the backside as shown.

5 Plug connector into control panel as shown.

6 Fasten the four screws attaching the control panel.

3

5

6

4

After installation has been completed, replace fuses in

transfer switch, replace 15 Amp fuse in control panel,

and set generator circuit breaker to its ON position.

Go to: LINK MONITOR WITH GENERATOR.

7 Assemble antenna piece to base.

8 Loosen inside roof bolt in corner.

9 Mount the antenna to the top of the roof. While

lifting roof in corner, lay antenna wire in space

between rubber gaskets.

10 Insert antenna wire to the OFF BOARD RADIO wire

until it clicks. Route wire away from sharp objects

and wire tie.

11 Tighten roof bolt (8) securely.

10

7

9

8

7/16

9

en

Not for

Reproduction

GENERATOR CONTROL PANEL

Three different styles, same button function.

MENU

OK

ESC

X

AUTO OFFMANUAL

MENU

OK

ESC

X

AUTO

menu

esc

auto off manual

auto

ok

menu

esc

ok

MENU

OK

menu

ok

OROR

Link Monitor with Generator

5 Important: Once the link has been made

(all icons turn OFF), press the OK button.

1 Press AUTO mode.

The REMOTE WIRELESS MONITOR

• Is for indoor use ONLY.

• Communicates with the generator

control panel.

• Has a range of up to 200 feet line

of sight.

red SERVICE NEEDED

BUTTON SYSTEM UPDATE

COLOR / ICON

green GENERATOR READY

green GENERATOR POWER

2 Install batteries correctly.

3 Press and hold together for about 5 seconds the

MENU and ESCAPE buttons.

• “LINKING MODE” will scroll across the digital

readout display.

4 Press and hold for 10 seconds the

system update BUTTON on the monitor.

• All three icons should turn ON

solid after 10 seconds.

• Once link has been made - all

icons turn OFF.

• If link has been unsuccessful

the wrench icon - flashes

4 seconds ON, 4 seconds OFF.

Repeat Steps 3 and 4.

GENERATOR READY will light for 5

seconds while the monitor starts up.

NOTE: It may take up to 1 minute for the monitor to

begin displaying the generator status correctly.

10

Not for

Reproduction

The wireless monitor receives data from the generator

every 10 minutes and displays the generator status

through 3 status icons

Pressing the SYSTEM UPDATE button will provide

current Generator Status by flashing the status icons.

When pressed, all 3 icons will flash until the generator

status is received.

Generator Status

Monitor/Generator

Status Codes

• Wireless Communication Lost - the wrench icon

will flash 20 fast pulses, then pause for 5 seconds,

and repeat the sequence until communication has

been restored. Communication lost issues can

typically be resolved by moving the wireless monitor

closer, within the home, to the standby generator.

See Optional Router Accessory Kit

• Linking Error or Not Linked - the wrench icon will

light red for 4 seconds, pause for 4 seconds, and

repeat the sequence until a successful link is

completed.

• During the weekly exercise cycle, the generator

will run for 20 minutes, but it will not supply power to

the home. During the exercise cycle, the monitor will

continue blinking the green shield icon.

Service Code Descriptions - name and number of

flashes are listed on the back side of the wireless

monitor.

Icon Lighting Codes

• No status icons illuminated - Generator in OFF

mode or check and replace batteries.

• Batteries Inserted - the shield icon will light for 5

seconds.

Optional Router Accessory Kit

The monitor has a line of sight range of up to 200 feet,

but this distance will decrease if the signal has to pass

through walls or other objects.

If upon installation and setup of the wireless monitor

system communication is not reliable, Optional Router

Accessory Kit may be needed. See Authorized Dealer

for more information.

The router is a small extender that can be used to

expand the range of a generator wireless network so

that network devices can seamlessly communicate

with one another.

The router can be plugged into any standard 110VAC

outlet within the home.

None of the service needed codes are cleared at the

wireless monitor. All alerts must be cleared at the

generator control panel.

11

red SERVICE NEEDED

BUTTON SYSTEM UPDATE

green GENERATOR READY

green GENERATOR POWER

COLOR / ICON

GENERATOR READY - When active, the shield

icon will flash green once every 7 seconds. The

green shield icon indicates that the generator is

in AUTO mode and that it is ready to run in the

event of a loss of utility power.

GENERATOR POWER - When active, the power

icon will flash green every 7 seconds. The green

power icon indicates that the generator is

supplying power.

SERVICE NEEDED - When the wrench icon

flashes red, refer to the service codes on the

back of the monitor or to the troubleshooting

guide in the generator manual. Call the nearest

authorized service dealer if problem cannot be

fixed.

en

Not for

Reproduction

BRIGGS & STRATTON PRODUCTS WARRANTY POLICY January 2014

LIMITED WARRANTY

Briggs & Stratton warrants that, during the warranty period specied below, it will repair or replace, free of charge, any part that is defective in

material or workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by

purchaser. This warranty is eective for and is subject to the time periods and conditions stated below. For warranty service, nd the nearest

Authorized Service Dealer in our dealer locator map at www.briggsandstratton.com. The purchaser must contact the Authorized Service

Dealer, and then make the product available to the Authorized Service Dealer for inspection and testing.

There is no other express warranty. Implied warranties, including those of merchantability and tness for a particular purpose, are

limited to the warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are

excluded to the extent exclusion is permitted by law. Some states or countries do not allow limitations on how long an implied warranty

lasts, and some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and

exclusion may not apply to you. This warranty gives you specic legal rights and you may also have other rights which vary from state to state

or country to country.**

WARRANTY PERIOD

** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement

or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods

repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. For warranty service, nd the

nearest Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or

writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.

The warranty period begins on the date of purchase by the rst retail or commercial consumer. “Consumer use” means personal residential

household use by a retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes.

Once a product has experienced commercial use, it shall thereafter be considered as a commercial use product for purposes of this warranty.

To ensure prompt and complete warranty coverage, register your product at the website shown above or at www.onlineproductregistration.com, or

mail the completed registration card (if provided), or call 1-800-743-4115 (in USA).

Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the

manufacturing date of the product will be used to determine the warranty period. Product registration is not required to obtain warranty service on

Briggs & Stratton products.

ABOUT YOUR WARRANTY

This warranty covers only defects in materials or workmanship. It does not cover damage caused by improper use or abuse, improper

maintenance or repair, or normal wear and tear.

Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not

described in the Operator’s Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage

will also not be provided if the serial number on the product has been removed or the product has been altered or modied in any way, or if the

product has evidence of abuse such as impact damage or water/chemical corrosion damage.

Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s

Manual, and serviced or repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-

original parts is not covered by warranty.

Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not

cover repairs when normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as lters, belts, cutting blades,

and brake pads (except engine brake pads) are not covered by warranty due to wear characteristics alone, unless the cause is due to defects in

material or workmanship.

Other Exclusions - This warranty excludes damage due to accident, abuse, modications, alterations, improper servicing, freezing or chemical

deterioration. Attachments or accessories that were not originally packaged with the product are also excluded. This warranty does not include

used, reconditioned, second-hand, or demonstration equipment or engines. This warranty also excludes failures due to acts of God and other

force majeure events beyond the manufacturer’s control.

Item Consumer Use Commercial Use

Accessory/Attachment/Equipment 12 months None

12

Page is loading ...

Simplicity 040450-00 User manual

Simplicity 040450-00 User manual

in other languages

Related papers