SeeYing TT-1852E User manual

Brand: SeeYing

Model: TT-1852E

Category: Audio turntables

Type: User manual

SeeYing TT-1852E comes with a wide range of capabilities that will allow you to enjoy music from various sources and give you a great user experience. Below you will find brief product information for SeeYing TT-1852E:

The device incorporates double insulation between hazardous mains voltage and user-accessible parts.
It has 3.5mm aux-in and headphone jacks, a USB socket, a line out socket, and a DC in jack, which provides versatile connectivity options.
It features a Phono mode, allowing you to connect your turntable to the system and play your vinyl records.
It has Bluetooth connectivity, allowing you to wirelessly stream music from your Bluetooth-enabled devices and enjoy high-quality audio through the speakers of this unit.

The device incorporates double insulation between hazardous mains voltage and user-accessible parts.
It has 3.5mm aux-in and headphone jacks, a USB socket, a line out socket, and a DC in jack, which provides versatile connectivity options.
It features a Phono mode, allowing you to connect your turntable to the system and play your vinyl records.
It has Bluetooth connectivity, allowing you to wirelessly stream music from your Bluetooth-enabled devices and enjoy high-quality audio through the speakers of this unit.

TURNTABLE SYSTEM

TT- 1852E

INSTRUCTION MANUAL

PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS UNIT

AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE

FULLY

INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK

HAZARD, DO

NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

The Caution Marking is located at the back enclosure of the apparatus.

The Rating plate is located at the back enclosure of the apparatus.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that product heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit

into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table recommended by the

manufacturer, or sold with the product. When a cart is used, use caution when moving

the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for a long periods of

time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

15. This appliance shall not be exposed to dripping or splashing water and that no object filled with

liquids such as vases shall be placed on the apparatus.

16. Do not overload wall outlet. Use only power source as indicated.

17. Use replacement part as specified by the manufacturer.

18. Upon completion of any service or repairs to this product, ask the service technician to perform

safety checks.

19. Power Sources - This product should be operated only from the type of power source indicated on

the marking label. If you are not sure of the type of power supply to your home, consult your product

dealer or local power company. For products intended to operate from battery power, or other

sources, refer to the operating instruction.

20. Object and Liquid Entry - Never push objects of any kind into this product through openings as they

may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

21. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified

service personnel under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the product,

c) If the product has been exposed to rain or water,

d) If the product does not operate normally by following the operating instructions. Adjust only

those controls that are covered by the operating instructions as an improper adjustment of other

controls may result in damage and will often require extensive work by a qualified technician to

restore the product to its normal operation.

e) If the product has been dropped or damaged in any way, and

f) When the product exhibits a distinct change in performance - this indicates a need for service.

22. Main plug is used as disconnect device and it should remain readily operable during intended use.

In order to disconnect the apparatus from the mains completely, the mains plug should be

disconnected from the mains socket outlet completely.

23. Excessive sound pressure from earphones and headphone can cause hearing loss.

24. Minimum distances of 10 cm around the apparatus for sufficient ventilation.

25. The ventilation should not be impeded by covering the ventilation openings with items, such as

newspapers, table-cloths, curtains, etc.

26. No naked flame sources, such as lighted candles, should be placed on the apparatus.

27. The use of apparatus in moderate climates.

This symbol indicates that this product incorporates

insulation between hazardous

mains voltage and

accessible

ts.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO

WIDE SLOT. FULLY INSERT THE PLUG TO MAIN POWER SOCKET.

PRECAUTION FORE USE

 UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.

 DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING

THE MAINS VOLTAGE AND ALL OTHER CONNECTIONS HAVE BEEN MADE.

 DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL

CENTIMETERS AROUND THE UNIT FOR VENTILATION.

IMPORTANT NOTES

 Avoid installing the unit in locations described below:

 Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters.

 Places subject to constant vibration.

 Dusty, humid or moist places.

SAVE THESE INSTRUCTIONS

ACOutlet

ACPlug

Location of controls

1) Dust cover

2) LED display

3) Speakers

4) Skip down / Skip up button

5) Play mode

6) On-Off / Function button

7) Memory button

8) TS (Track Separation) button

9) Record button

10) 3.5 mm headphone jack

11) 3.5mm aux-in jack

12) USB socket

13) Volume knob

14) Remote sensor

15) Play/Pause/Stop button

16) Spindle adaptor

17) Turntable speed selector

18) Auto stop switch

19) Tone arm rest

20) Line out socket

21) FM Antenna

22) DC in jack

23) AC adaptor

24) DC plug

Caution:

Usage of controls or adjustments or performance of procedures other than those specified herein may result in

hazardous radiation exposure.

This unit should not be adjusted or repaired by anyone except qualified service personnel.

Connection

1. Connect DC plug (24) of the AC/DC adaptor (23) to the DC in jack (22).

2. Then connect the AC/DC adaptor (23) to the AC outlet.

3. Press the On-Off/Function button (6.), the LED display (2.) will show “ Lod ”, then change to “ bLUE”. It means

the power supply is normal. Now your system is ready to operate.

4. The Function modes are switch from:

bLUE (Bluetooth)  USB (only if the USB drive is being connected)  FM radio  PH (Phono)/Aux

* Before the LED display changes to the name of the mode, it will show “Lod” for a while. So, wait for a while

for the function mode.

* If no USB drive is being connected before switching the function mode, the unit will skip the USB mode and

switch from Bluetooth mode to FM mode directly.

* The Phono mode and the AUX-in mode are sharing the same function mode and once the Aux-in jack (11.)

is plugged in, it will automatically switched to Aux-in mode from Phono mode.

5. To switch off the unit, press and hold the on/off button (6.) for 2-3 second and the LED display will turn off

meaning the unit is switch off.

Bluetooth connecting and playback

1. Press the On-Off/Function button (6.) to turn on the unit and the LED display (2.) will show “ Lod ”, then

change to “ bLUE”.

2. You may need to press the

On-Off/Function button (6.) until the LED display (2.) shows “ bLUE ”.

3. The text “ bLUE ” on the display will flash meaning the unit is searching and waiting to connect to Bluetooth.

4. Switch the Bluetooth function of your Bluetooth device on (such as a mobile phone) and select the

Bluetooth equipment code “TT-1852E” to connect.

5. When the Bluetooth device has connected successfully, the text “ bLUE ” will no longer flash but be static.

6. Start playback of the music on your Bluetooth device and enjoy the music through the speakers of this

unit.

7. Adjust the Volume knob (13.) to the desired volume level.

8. You can press the Play/pause button (15.), Skip up or Skip down (4.) button to control the

music playback.

9. If you want to connect the unit to another Bluetooth enabled device after you’ve already successfully paired,

turn off the Bluetooth on the device that was previously paired with the unit. The text “bt” on the display will

begin flashing, repeat step 3-6 above.

Notes:

1. Refer to the manual of your cell phone, tablet PC, computer or other Bluetooth enabled devices for Bluetooth

operation since it may vary from model to model.

2. If your Bluetooth enabled device does not support A2DP profile, it will not play the music through the speaker,

even if paired (linked).

3. Remember to turn off the unit when you have finished listening,

4. Don't forget to switch off the power of your Bluetooth device as well.

5. The music playback will automatically be paused when you have an incoming call. When the call is ended,

the unit will start playing again.

6. The Bluetooth operation will be interrupted if Aux-in jack is being connected.

Listening to Radio

Manual tuning

1. Press the On-Off/Function button (6.) to turn on the unit and press it again until the LED display (2.) shows FM

radio frequency and also “ FM “ on the left corner of the LED display (2.).

2. Press the Skip down or Skip up (4.) button to tune your desired station.

3. Adjust volume knob (13.) for the desired volume level.

Auto tuning

1. Press the On-Off/Function button (6.) to turn on the unit and press it again

until the LED display (2.) shows FM

radio frequency and also “ FM “ on the left corner of the LED display (2.)

2. Press and hold the Skip down or Skip up (4.) button for 1-2 seconds and then release.

3. The unit will start seeking automatically and stop until a radio station is reached

4. Repeat step 2 until the desired radio station is being reached.

5. Adjust volume knob (8) for the desired volume level

Hints for best reception:-

FM : the receiver has a built-in FM wire antenna (21.) hanging at the rear cabinet. This wire should be totally

unraveled and extended for best reception.

Preset stations

You can store up to total of 20 radio stations in the memory.

1. Tune to the desired radio station by “ manual ” or “ auto ” tuning method.

2. Press and hold the “Memory” button (7.) for 2-3 seconds to enable the memory state until the preset station

number and “MEM” is appearing on the LED display.

3. Press Skip up or Skip down (4.) button to select the desired station memory for storage.

4. Press “Memory” button (7.) again to confirm the setting.

5. Repeat step 1 to 4 to store other stations.

6. Press Mem button (7.) once and select the preset station number by pressing Skip up (4.) button to recall

the preset station. Then the unit will tune to the preset station directly.

Listen to the phono

Noted:

- Remove the stylus protector.

- Be sure that the tone arm is being detached from the tone arm rest before

operating and re-secured again afterwards.

- Be sure that the Aux-in jack (11.) is not being connected during the phono

operation (see below point 2 of the remark).

1. Press the On-Off/Function button (6.) to turn on the unit and press it again

until the LED display (2.) shows “ PH

“ (Phono).

2. Set the speed selector (17.) to the proper position depending on the record to be played.

3. Place the record on the platter (use the spindle adaptor (16.) if required).

4. Lift the tone arm from the rest and slowly move it to the record side. The platter will

start to rotate.

5. Place the tone arm by the pick up holder to the desired position of the record.

6. Adjust the volume (13.) to the desired level.

7. At the end of record, the platter will automatically stop rotating. Lift the tone arm from

the record and return it to the rest.

8. To stop manually, lift the tone arm from the record and return it to the rest.

Remark :

1. As some kind of record the auto-stop area was out of the unit setting, so it will stop before the last track finish.

In this case, select the auto-stop switch (18.) to “ off “ position, then it will run to the end of the record but will

not stop automatically (turn off the unit by press and hold the

On-Off/Function button (6.) for 2-3 seconds, or

switch back the auto-stop switch to “ on “ position to stop the platter rotate). Then put back the tone arm to

the rest position.

2. The Phono mode and the AUX-in mode are sharing the same function mode and once the Aux-in jack

(11.) is plugged in, it will automatically switched to Aux-in mode from Phono mode. So, please be

ensured that the Aux-in jack is not being connected if you want to playback the record.

Aux-in connection

Connect the unit to any auxiliary device (i.e. MP3 player, or iPod® (not included) by connecting the aux in jack (11.)

with one end of 3.5mm stereo cable (not provided) and the other end connect to the auxiliary device to perform the

music.

1. Plugged the Aux in jack from your external device.

2. Press the On-Off/Function button (6.) to turn on the unit and press it again

until the LED display (2.) shows “ AUX ”

mode.

3. Start to playback your device and adjust On-off/Volume knob (13.) to the desire volume level. If the distortion

was too high, reduce the volume level of your auxiliary device.

Playback of MP3 song via USB storage media

Connecting

The system is able to decode and playback all MP3 file which stored in the memory media

with USB connector (not supplied). Plug in the USB pen drive to the USB socket (12.).

Connecting the USB upside down or backwards could damage the audio system or

the storage media (USB thumb drive). Check to be sure the direction is correct before

connection.

1) Plug in the USB drive with the USB symbol facing upwards, making sure it is fully

inserted.

2) Press the On-Off/Function button (6.) to turn on the unit and press it once again and the

LED display (2.) will show “ Lod ”.

3) The system will start reading the storage media after connecting and will show the total number of folders or

tracks on the LED display (2.) after read.

4) The system will start playback automatically. You can press the Play/pause button (15.), Skip up or

Skip down (4.) button to control the music playback.

5) Adjust the volume (13.) to the desired level.

 Pause / Play mode (no Stop mode for USB playback)

1. To interrupt, press the Play/Pause/Stop button (15.) once, the playing time will be freeze & flashing on the

LED display (2.). Press again to resume normal playback.

 Skip/search mode (skip/search up /skip/search down )

1. During play or pause mode, if Skip up button (4.) is pressed. It will go to next track and display the track no.

and then remain in play or pause mode.

2. Alternatively, press Skip down button (4.) will go to the previous track and remain in play or pause mode.

3. If press and hold the Skip up /down button (4.) during MP3 playback, the playing track will go fast

forward or backward until the button being released.

Remark

- USB port does not support connection with USB extension cable and is not designed for

communication with computer directly.

- If no USB is being plugged before switching the function mode, the unit will skip the USB mode and

switch from Bluetooth mode to FM mode directly. So, please ensure the USB device must be plugged

in before all operation.

- The system can detect and read the file under MP3 and format only though the USB port.

- There is no Stop mode, but only pause mode for USB playback.

- Due to variances in MP3 encoding format, some MP3 players may not play when connected to the

USB socket. Please note this is not a malfunction of the system.

MP3 track format requirement:-

- MP3 bit rate : 32 kbps ~ 320 kbps

- The performance of playing MP3 file is various from the quality of encoding file and the method of encoding.

 Repeat/Intro/Random mode (on remote control)

Press the Repeat/Intro/Random button before or during playback, a single track, single folder or all the tracks can

be played in difference mode as follow:-

(1) Repeat 1 (2) Random (3) Repeat one folder

(5) Off mode (4) Repeat all tracks

Play mode Indicator on LED display

Repeat single track ONE

Random mode rAn

Repeat single folder FoLd

Repeat all tracks ALL

Off mode -----------------

 Repeat play

You can listen the desired tracks or folder or all track repeatedly by this function.

 Random play

You can listen all the tracks or folder in a random order by this function

Removing of USB

To remove the USB turn off the power or switch the function mode to either tuner or phono first. Then, un-plug the

USB by pulling out directly.

Encoding from Phono or Aux in into mp3 file

The system is able to encode the Phono or Aux in or FM tuner to MP3 format and recording at memory media with

USB connecting port.

A) Phono encoding

1) Plug in the USB flash drive you wish to record onto (make sure it has enough free space).

2) Press the On-Off/Function button (6.) to turn on the unit and press it again until the LED display (2.) shows

“ PH ” (Phono) mode.

3) Follow the instruction “Listen to the Phono” above and get prepared the playback of the desired track you

want to record but do not start the playback.

4) Press the Record button (9.) directly and a “REC” text will appear at the bottom right hand corner of the LED

display (2.) meaning the system is starting the encoding mode.

5) Start playback at Phono for the track which you want to record.

6) After finish of recoding, press and the Play/Pause/Stop button (15.) and the “REC” text will disappear from

the LED display (2.).

B) Aux-in encoding

1) Plug in the USB flash drive you wish to record onto (make sure it has enough free space).

2) Connect the external device via the Aux-in connection.

3) Press the On-Off/Function button (6.) to turn on the unit and press it again until the LED display (2.) shows

“ PH ” (Phono) mode.

4) Follow the instruction “Listen to the Phono” above and get prepared the playback of the desired track you

want to record but do not start the playback.

5) Press the Record button (9.) directly and a “REC” text will appear at the bottom right hand corner of the LED

display (2.) meaning the system is starting the encoding mode.

6) Start playback at Phono for the track which you want to record.

7) After finish of recoding, press and the Play/Pause/Stop button (15.) and the “REC” text will disappear from the

LED display (2.).

Remark:-

- The recording speed is 1:1 and according to the actual plying time.

- The system will create a “JL_REC “ folder “and then store the encoding track in it.

- The recording format is default at – MP3 bit rate : 128 kbps, sampling rate : 44.1kHz

- No song title will be recorded during encoding mode

- To interrupt the recording, press the “Record “ button (6) again during record mode.

E) Track separation (by remote handset)

You can divide the recording music from phono or tape to USB track by trace during encoding. Every time when

press the“ “ (track separation) button once at remote handset during encoding from phono/Aux to USB, the

system will generate a new track and continuous the recording.

SPECIFICATIONS

DC: 5V 2A

Bluetooth

Maximum communication range: Line of sight approx. 10m (30 feet)

Remote control transmitter

Button description

1) On/Off Press to switch on/off the system.

2) Mute Press to suspend the sound output temporally.

Press again to resume the sound output.

3) Memory In FM mode, press and hold to preset the radio

station. Or press to recall the preset station.

4) Skip down In USB mode : to select previous track

In FM mode: tuning the radio station

5) Rec Press to encode the aux/phono to USB in MP3 format

6) Function Press to select different function mode

7) Play mode Press to active repeat /random function for

USB playback

8) Play/pause Press once to start USB playback. Press once again to

pause play temporarily

9) Skip up In USB mode : to select next track

In FM mode: tuning the radio station

10) TS In encoding mode : press to active track separation function

11) Stop In encoding mode : press to stop the recording function

BATTERY REPLACEMENT

The battery compartment is located on the back of the remote control.

1. Remove the battery compartment door by pressing in on the tab and lifting it off.

2. Insert two AAA size batteries (excluded) into the battery compartment following the polarity markings inside

the battery compartment.

3. Replace the battery compartment door.

Battery Precautions

 Replacement of batteries must be done by an adult.

 The supply terminals are not to be short-circuited.

 Non-rechargeable batteries are not to be recharged.

 Exhausted batteries are to be removed.

 Only batteries of the equivalent type are to be used.

 Batteries are to be inserted with the correct polarity.

 Dispose of batteries properly. Do not dispose of batteries in

fire. The batteries may explode or leak.



SeeYing TT-1852E User manual

Brand: SeeYing

Model: TT-1852E

Category: Audio turntables

Type: User manual

The device incorporates double insulation between hazardous mains voltage and user-accessible parts.
It has 3.5mm aux-in and headphone jacks, a USB socket, a line out socket, and a DC in jack, which provides versatile connectivity options.
It features a Phono mode, allowing you to connect your turntable to the system and play your vinyl records.
It has Bluetooth connectivity, allowing you to wirelessly stream music from your Bluetooth-enabled devices and enjoy high-quality audio through the speakers of this unit.

Download PDF

report

SeeYing TT-1852E User manual

SeeYing TT-1852E User manual

Related papers

Other documents