Furniture of America IDF-7315N Installation guide

Brand
Furniture of America
Model
IDF-7315N
Type
Installation guide

Furniture of America IDF-7315N is a dresser with a mirror that requires assembly. It comes with all the necessary hardware and an Allen key for assembly. The dresser has a support leg that can be adjusted according to the ground level. The mirror is attached to the dresser with bolts and washers. The dresser is made of sturdy materials and is designed to last. It is easy to assemble and maintain, and it is recommended to check and tighten any loose hardware every six months.

Furniture of America IDF-7315N is a dresser with a mirror that requires assembly. It comes with all the necessary hardware and an Allen key for assembly. The dresser has a support leg that can be adjusted according to the ground level. The mirror is attached to the dresser with bolts and washers. The dresser is made of sturdy materials and is designed to last. It is easy to assemble and maintain, and it is recommended to check and tighten any loose hardware every six months.

Assembly Instructions
EASY
DIFFICULT
Page 1 of 4
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7315D&M
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench
(Included)
Assembly Instructions
EASY
DIFFICULT
Page 1 of 8
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7315Q/CM7315EK
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench
(Included)
Phillips Screwdriver
Wrench
(Included)
(Not Included)
Assembly Instructions
EASY
DIFFICULT
Page 1 of 8
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7315CK
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench
(Included)
Phillips Screwdriver
Wrench
(Included)
(Not Included)
Rev: 18-03-31
Rev: 18-03-31
For more information contact our team: [email protected]
For more information contact our team: [email protected]
For more information contact our team: [email protected]
Rev: 18-
Page 2 of 4
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
Page 2 of 8
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
Page 2 of 8
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED
FURNITURE OF AMERICA.ALL RIGHTS RESERVED
FURNITURE OF AMERICA.ALL RIGHTS RESERVED
Parts List
Hardware List
#1 x 1pc
#2 x 1pc
#A x 6pcs
#B x 6pcs
#C x 6pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Mirror
#3 x 2pcs
#D x 1pc
Page 3 of 4
Dresser
Back Rail
Bolt Ø1/4" x 1-1/2"
Spring Washer Ø1/4"
Flat Washer
Ø1/4"
Allen Key 4mm
#4 x 1pc
Support Leg 28x28x115mm
Ø1/4
1278mm
40mm
35mm
555mm
98mm
555mm
35mm
30x10mm
20mm
Parts List
Hardware List
#1 x 1pc
#2 x 2pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Headboard Panel
#3 x 1pc
#6 x 1set
#7 x 2pcs
#5 x 1pc
Page 3 of 8
#4 x 2pcs
Headboard Leg (L&R)
Footboard
Side Rail
Bed Slat 13pcs
Headboard Support
Support Leg 28 x 28 x 170mm
#E x 15pcs
#B x 12pcs
#C x 12pcs
Lock Washer Ø5/16"
Flat Washer
Ø5/16"
#D x 1pc
#F x 8pcs
#G x 8pcs
#H x 1pc
Screw #4 x 30mm
Allen Key 4mm
Threaded Pins Ø5/16" x 3-1/2"
Hex Nut Ø5/16"
Wrench 14mm
#A x 12pcs
Bolt Ø5/16" x 2"
Ø1/4
#8 x 5pcs
Support Leg 28 x 28 x 390mm
Ø1/4
Parts List
Hardware List
#1 x 1pc
#2 x 2pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Headboard Panel
#3 x 1pc
#6 x 1set
#7 x 2pcs
#5 x 1pc
Page 3 of 8
#4 x 2pcs
Headboard Leg (L&R)
Footboard
Side Rail
Bed Slat 13pcs
Headboard Support
Support Leg 28 x 28 x 170mm
#E x 15pcs
#B x 12pcs
#C x 12pcs
Lock Washer Ø5/16"
Flat Washer
Ø5/16"
#D x 1pc
#F x 8pcs
#G x 8pcs
#H x 1pc
Screw #4 x 30mm
Allen Key 4mm
Threaded Pins Ø5/16" x 3-1/2"
Hex Nut Ø5/16"
Wrench 14mm
#A x 12pcs
Bolt Ø5/16" x 2"
Ø1/4
#8 x 5pcs
Support Leg 28 x28 x 390mm
Ø1/4
1200mm
#3
#2
#1
#4
Page 4 of 4
#A x 6pcs
#B x 6pcs
#C x 6pcs
ASSEMBLY IS COMPLETED
#2
#4
#9 x 1pc
Slat Center Support
#A x 12pcs
#B x 12pcs
#C x 12pcs
#D
#9 x 1pc
Slat Center Support
#10 x 2pcs
Top Bed Rail
#L x 12pcs
#M x 12pcs
Lock Washer Ø1/4"
Flat Washer
Ø1/4"
#K x 12pcs
Bolt Ø1/4" x 1-1/2"
#I x 8pcs
Nut Ø5/16"
#I x 8pcs
Nut Ø5/16"
#B
#D
#A
#C
#3
#2
#1
Parts List
Hardware List
Page 4 of 8
#1
#2R
#4
#4
#3
#7
#5
#6
#8
#9
#10
#1
#2R
#2L
#4
#4
#3
#7
#5
#6
#8
#9
Parts List
Hardware List
Page 4 of 8
#10 x 2pcs
Dusty Panel
#J x 8pcs
Screw #4 x 15mm
#10
#10
#11 x 2pcs
Dusty Panel
#N x 8pcs
Screw #4 x 15mm
#11
#11
Attach support leg (#4) to the bottom of the dresser (#2). Adjust
leveler on the support leg (#4) according to ground level.
Align mirror supports to the holes of the mirror (#1), then
secure by using bolts (#A) with washers (#B,C).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Furniture of America IDF-7315N Installation guide

Brand
Furniture of America
Model
IDF-7315N
Type
Installation guide

Furniture of America IDF-7315N is a dresser with a mirror that requires assembly. It comes with all the necessary hardware and an Allen key for assembly. The dresser has a support leg that can be adjusted according to the ground level. The mirror is attached to the dresser with bolts and washers. The dresser is made of sturdy materials and is designed to last. It is easy to assemble and maintain, and it is recommended to check and tighten any loose hardware every six months.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents