Livex Lighting 2165-61 Operating instructions

2165-61
Livex Lighting
Brand
Livex Lighting
Model
2165-61
Type
Operating instructions
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING &
&
&
& INSTALLATION
INSTALLATION
INSTALLATION
INSTALLATION INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS PRODUCT#
PRODUCT#
PRODUCT#
PRODUCT# 2181
2181
2181
2181 2281
2281
2281
2281 2381
2381
2381
2381 2386
2386
2386
2386 2162
2162
2162
2162 2165
2165
2165
2165 2168
2168
2168
2168
2172
2172
2172
2172 OUTDOOR
OUTDOOR
OUTDOOR
OUTDOOR
WALL
WALL
WALL
WALL
MOUNT
MOUNT
MOUNT
MOUNT LIGHT
LIGHT
LIGHT
LIGHT FIXTURE
FIXTURE
FIXTURE
FIXTURE
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
MOUNTING
MOUNTING
MOUNTING
MOUNTING THE
THE
THE
THE FIXTURE
FIXTURE
FIXTURE
FIXTURE
Installation
Installation
Installation
Installation (see
(see
(see
(see fig.1)
fig.1)
fig.1)
fig.1)
1. Shut off the power at the circuit breaker and remove old
fixture, including the cross bar.
2. Carefully unpack new fixture and lay all the parts on a clear
surface. Take care not to lose any small parts necessary for
installation.
3. Attach the mo unting screw part way into the side hole of the
crook cross bar , then lock it securely with hex nut until
becoming . Attach the cross bar to the junction box using two
box screws . The side of the cross bar marked “ GND ” must
face out.
4. Follow wiring instructions carefully (see
(see
(see
(see fig.2)
fig.2)
fig.2)
fig.2)
5. Using the end of arm(A) hook the lamp body's loop,
aligning the end hole of the arm(A) with the top hole of back
plate , lock it securely with screw(E) and hex nut. Put the
candle sleeve(D) over the lamp holder.
6. Attach the back plate of the lamp body(B) onto the junction
box, aligning screws on cross bar with mounting holes and
lock it securely with the ball nuts(C).
7.
7.
7.
7. Install the light bulb s in accordance with the fixture
’
s
specifications. DO
DO
DO
DO NOT
NOT
NOT
NOT EXCEED
EXCEED
EXCEED
EXCEED THE
THE
THE
THE MAXIMUM
MAXIMUM
MAXIMUM
MAXIMUM
WATTAGE
WATTAGE
WATTAGE
WATTAGE
RATING!
RATING!
RATING!
RATING!
8. With
With
With
With silicone
silicone
silicone
silicone caulking
caulking
caulking
caulking compound,
compound,
compound,
compound, caulk
caulk
caulk
caulk completely
completely
completely
completely
around
around
around
around where
where
where
where back
back
back
back of
of
of
of cover
cover
cover
cover meets
meets
meets
meets with
with
with
with the
the
the
the wall
wall
wall
wall surface
surface
surface
surface
to
to
to
to prevent
prevent
prevent
prevent water
water
water
water from
from
from
from seeping
seeping
seeping
seeping into
into
into
into outlet
outlet
outlet
outlet box.
box.
box.
box.
Wiring
Wiring
Wiring
Wiring (see
(see
(see
(see fig.2)
fig.2)
fig.2)
fig.2)
1. Connect the electrical wires as follows. Connect the
black wire from the fixture to the black house (hot)
Wire. Connect the white wire from the fixture to the
white (neutral) house wire. Make sure all wire nuts are
secured.
You
may wrap the connections with electrical
tape. If your outlet box has a ground wire (green or bare
copper) connect fixture
’
s ground wire to it. Otherwise
attach the bare copper fixture wire to the green ground
screw on the cross bar.
2.Tuck the wire connections neatly into the wall junction
box.
F ig.1
Fig.2
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
R
Listed
U
L
R
  • Page 1 1

Livex Lighting 2165-61 Operating instructions

2165-61
Livex Lighting
Brand
Livex Lighting
Model
2165-61
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents