Feiss P1437PN Installation guide

Feiss
Brand
Feiss
Model
P1437PN
Type
Installation guide

Feiss P1437PN is a 1 Light Mini-Pendant that can be installed in damp locations. It is compatible with incandescent and LED lamps. Incandescent lamps may be dimmed with a standard incandescent dimmer while LED lamps require a specific LED dimmer. For your convenience, this fixture can be used with a minimum 90°c supply conductors.

Feiss P1437PN is a 1 Light Mini-Pendant that can be installed in damp locations. It is compatible with incandescent and LED lamps. Incandescent lamps may be dimmed with a standard incandescent dimmer while LED lamps require a specific LED dimmer. For your convenience, this fixture can be used with a minimum 90°c supply conductors.

1
Installation Instructions for
Pendant
Determine the wanted height of the fixture by feeding the cord through the canopy and moving the cord up or down.
Place the cord in between the two cord clips and secure it in place using the clip screws.
Trim the cord leaving enough for electrical connections. From the end of the cord, strip the insulation 4” and then strip the end of
the wires. Note: Make sure not to nick the inner wires.
Secure the mounting plate to the junction box.
Connect the fixture to a suitable ground in accordance to local electrical codes.
Connect the white fixture wire (square and/or rigid) to the neutral power line wire with a wire nut.
Connect the black fixture wire (round and/or smooth) to the hot power line wire with a wire nut.
Neatly place all the wires into the junction box, place the canopy onto the mounting plate, and secure it in place with the set
screws using an Allen key.
Place the shade onto the socket and secure it in place by screwing the collar nut onto the socket using the shade tool.
Screw the lamp into the socket. Refer to the label on the socket for Max Wattage information.
1
2
1A
CAUTION RISK OF FIRE-
This product must be installed in accordance with
the applicable installation code by a person familiar
with the construction and operation of the product
and the hazards involved.
Use minimum 90°c supply conductors.
CORD
3
4
5
7
8
6
9
7
8
CANOPY
SET SCREW
ALLEN KEY
MOUNTING PLATE
JUNCTION BOX
6
GP I :ENERAL RODUCT NFORMATION
These fixtures are intended to be installed utilizing compliant junctionNEC
boxes.
This product is safety listed for damp locations.
Incandescent lamps may be dimmed with a standard incandescent dimmer.
LED LEDlamps may be dimmed with a dimmer. Consult lamp manufacturer for
additional information.
This instruction shows a typical installation.
CORD
CANOPY
CORD CLIP
CLIP SCREW
9
2
3
Rubin 1 Light Mini-Pendant
1.0
P1437
P1437
LAMP
COLLAR NUT
10
SHADE
SHADE TOOL
10
Page is loading ...
Page is loading ...
SAVETHESE INSTRUCTIONS!
4
7400 Linder Ave, Skokie, 60077IL
800.969.3347
www.Feiss.com
© 2017 Feiss.All rights reserved.The "Feiss" graphic is a
registered trademark of Feiss. Feiss reserves the right to
change specifications for product improvements without notification.
A Generation Brands Company
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Feiss P1437PN Installation guide

Feiss
Brand
Feiss
Model
P1437PN
Type
Installation guide

Feiss P1437PN is a 1 Light Mini-Pendant that can be installed in damp locations. It is compatible with incandescent and LED lamps. Incandescent lamps may be dimmed with a standard incandescent dimmer while LED lamps require a specific LED dimmer. For your convenience, this fixture can be used with a minimum 90°c supply conductors.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents